AGA marvel ML15BC User manual

Page is loading ...

2

NOTE

!

CAUTION

CONTENTS

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the anti-tip device .................................................6

Product Dimensions ...........................................................8

Using your Electronic control ............................................10

Starting your appliance ..................................................10

Sleep mode ...................................................................10

Turning your appliance "ON" or "OFF" ..........................10

Adjusting the temperature .............................................11

Interior display lighting ...................................................11

Temperature mode ........................................................11

Control lock ....................................................................11

Alarms ............................................................................12

Door ajar ...................................................................12

Power failure .............................................................12

Temperature alarm ....................................................12

Vacation mode .............................................................13

Overlay door panel installation .........................................14

Shelving congurations .....................................................21

Care and cleaning .............................................................24

Energy saving tips ............................................................24

Door alignment .................................................................25

Obtaining service .............................................................25

Troubleshooting ................................................................26

Warranty ...........................................................................27

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

!

WARNING

WARNING-You can be killed or seriously injured if

you do not follow these instructions.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

is committed to building a quality product

in an environmentally friendly manner. Our processes are

tightly controlled and closely monitored. We have achieved

certications in ISO 9001 for quality assurance, ISO 14001

for environmental management, and OHSAS 18001 for oc-

cupational health and safety from Lloyd’s Register Quality

Assurance.

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals

known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals

known to the State of California to cause birth defects or

other reproductive harm..

3

NOTE

!

CAUTION

!

CAUTION

!

CAUTION

XXXXXXXXXXXX

UNPACKING YOUR APPLIANCE

Warranty Registration

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.agamarvel.com.

The following information will

be required when registering

your appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the left

side near the top. (See gure 1).

Help Prevent Tragedies

Child entrapment and suffocation are not problems of the

past. Junked or abandoned refrigerators are still dangerous

- even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please follow

the instructions below to help prevent accidents.

Before you throw away your old refrigerator or freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not easily

climb inside.

!

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Dispose of the plastic bags which can be a suffocation

hazard.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

Figure 1

Online registration

available at

www.agamarvel.com

4

!

CAUTION

!

WARNING

An optional stacking kit, shown in Table "A", is required

to stack products. Failure to use a stacking kit could

result in personal injury. Contact your dealer or Aga

Marvel customer service at 800-223-3900 to order.

Color Door Swing Kit Part Number

Stainless Steel Left Hand 42249095

Stainless Steel Right Hand 42249096

Black Left Hand 42249097

Black Right Hand 42249098

White Left Hand 42249099

White Right Hand 42249100

Table A

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

ensure your product performs to specications, the recom-

mended installation location temperature range is from 55

to 100°F (13 to 38°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unob-

structed. Overlay door models with articulated hinges are

intended for built-in applications only.

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to ow through the condenser heat ex-

changer. Restrictions to this air ow will result in increased

energy usage and loss of cooling capacity. For this reason

it is important this area not be obstructed and the grille

openings kept clean. AGA MARVEL does not recommend

the use of a custom made grille as air ow may be restrict-

ed. (See Figure 2).

Front Leveling

Legs

Figure 2

Rear

Leveling

Legs

Front Grille,

keep this area

open.

INSTALLING YOUR APPLIANCE

Leveling Legs

Adjustable legs at the front and rear corners of the appli-

ance should be set so the unit is rmly positioned on the

oor and level from side to side and front to back. The over-

all height of your Marvel appliance may be adjusted higher

(by turning the leveling leg out, CCW) and lower (by turning

the leveling leg in, CW) dimensions as shown in Table "B".

To adjust the leveling legs, place the appliance on a solid

surface and protect the oor beneath the legs to avoid

scratching the oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 5).

Model Door Style

Minimum

Height

Maximum

Height

ML(15)(24)* (S) or (G)

33

3

⁄4"

(85.7 cm)

34

3

⁄4"

(88.3 cm)

ML(15)(24)* (P or (F)

34"

(86.4 cm)

35"

(88.9 cm)

MA24* (S) or (G)

31

1/

8"

(79.1 cm)

32

1

⁄8"

(81.6 cm)

MA24* (P or (F)

31

3

⁄8"

(79.7 cm)

32

3

⁄8"

(82.2 cm)

Table B

5

NOTE

Figure 6

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

!

WARNING

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 6). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

Front grille screw

Front grille

Figure 5

INSTALLING YOUR APPLIANCE

Figure 3

Figure 4

Do not remove

ground prong

6

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

!

CAUTION

NOTE

Bottom View of

Refrigerator

Anti-Tip

Bracket

Leveling Leg

Front of cabinet

21

1

⁄2"

(54.6 cm)

Figure 7

Floor Mount Installation

The anti-tip bracket is to be located on the oor in the left or

right rear corner of the refrigerator as shown in Figure 7.

Step by step instructions for locating the

position of the bracket:

1) Decide where you want to place the refrigerator. Slide it

into place, being careful not to damage the oor, leaving 1"

(2.5 cm) of clearance from the rear wall to allow room for

the anti-tip bracket.

2) Raise the rear leveling legs approximately

1

⁄4" (6 mm) to

allow engagement with the anti-tip bracket. Level the unit

by adjusting all the leveling legs as required. Turning the

leveling leg counterclockwise will raise the unit and clock-

wise will lower the unit.

3) Make sure the refrigerator is in the desired location, then

mark on the oor the rear and side corner of the cabinet

where the anti-tip bracket will be installed. If the installation

does not allow marking the rear corner of the cabinet, then

make temporary lines on the oor marking the front corner

of the cabinet, excluding the door. Slide the refrigerator out

of the way. From the temporary line extend the sidewall line

back 21

1

⁄2" (54.6 cm) as shown in Figure 8.

4) Align the anti-tip bracket to the marks on the oor so

the side of the bracket lines up with the side of the cabinet

mark, and the "V" notches on the anti-tip bracket line up

with the end of the 21

1

⁄2" (54.6 cm) line (Rear of cabinet

line).

5) Fasten the anti-tip bracket to the oor using the supplied

screw. (See Figure 8).

6) Slide the cabinet back into position, making sure the rear

cabinet leveling leg slides under the anti-tip bracket engag-

ing the slot.

!

WARNING

• ALL APPLIANCES CAN TIP

RESULTING IN INJURY.

• INSTALL THE ANTI-TIP

BRACKET PACKED WITH

THE APPLIANCE.

• FOLLOW THE INSTRUC-

TIONS BELOW

Any nished ooring should be protected with appropriate

material to avoid damage when moving the unit.

If installing on a concrete oor, concrete fasteners are

required, (not included with the anti-tip kit).

Anti-Tip Device

!

WARNING

If your refrigerator is not located under a counter

top (free standing), you must use an anti-tip device

installed as per these instructions. If the refrigerator is

removed from its location for any reason, make sure

that the device is properly engaged with the anti-tip

bracket when you push the refrigerator back into the

original location. If the device is not properly engaged,

there is a risk of the refrigerator tipping over, with the

potential for property damage or personal injury.

7

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

21

1

⁄2"

(54.6 cm)

"V" notches

in bracket

"V" notches

in bracket

Side of cabinet line

Figure 8

Front of cabinet line

Rear of cabinet line

Rear Leveling leg

Screw

Figure 8a

NOTE

When the oor mounted anti-tip bracket is used the mini-

mum adjusted height of the cabinet is increased by

3

⁄8" (9 mm).

8

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

ML15**(G) or (S)

15"

(38.1 cm)

**34" to 35"

(86.4 to 88.9 cm)

*

14

7

⁄8"

(37.8 cm)

33

3

⁄4" to 34

3

⁄4"

(85.7 to 88.3 cm)

23

⁄32"

(60.2 cm)

25

21

⁄32"

(65.2 cm)

37

13

⁄32"

(95 cm)

16

11

⁄16"

(42.4 cm)

ML15**(P) or (F)

15"

(38.1 cm)

**34

1

⁄4" to 35

1

⁄4"

(87 to 89.5 cm)

*

14

7

⁄8"

(37.8 cm)

34" to 35"

(86.4 to 88.9 cm)

22

7

⁄8"

(58.1 cm)

-

37

1

⁄2"

(95.2 cm)

14

1

⁄8"

35.9 cm)

ML24**(G) or (S)

24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm)

*

23

7

⁄8"

(60.7 cm)

33

3

⁄4" to 34

3

⁄4"

(85.7 to 88.3 cm)

23

⁄32"

(60.2 cm)

25

21

⁄32"

(65.2 cm)

46

13

⁄32"

(117.9 cm)

25

11

⁄16"

(65.2 cm)

ML24**(P) or (F)

24"

(61 cm)

**34

1

⁄4" to 35

1

⁄4"

(87 to 89.5 cm)

*

23

7

⁄8"

(60.7 cm)

34" to 35"

(86.4 to 88.9 cm)

22

7

⁄8"

(58.1 cm)

-

46

1

⁄2"

(118.1 cm)

23

1

⁄8"

(58.7 cm)

MA24**(G) or (S)

24"

(61 cm)

** 31

3

⁄8" to 32

3

⁄8"

(79.7 to 82.2 cm)

*

23

7

⁄8"

(60.7 cm)

31

1

⁄8" to 32

1

⁄8"

(79.1 to 81.6 cm)

23

⁄32"

(60.2 cm)

25

21

⁄32"

(65.2 cm)

46

13

⁄32"

(117.9 cm)

25

11

⁄16"

(65.2 cm)

MA24**(P) or (F)

24"

(61 cm)

** 31

5

⁄8" to 32

5

⁄8"

(80.3 to 82.9)

*

23

7

⁄8"

(60.7 cm)

31

3

⁄8" to 32

3

⁄8"

(79.7 to 82.2 cm)

22

7

⁄8"

(58.1 cm)

-

46

1

⁄2"

(118.1 cm)

23

1

⁄8"

(58.7 cm)

DOOR STYLE

(G) Glass Frame Door

(S) Solid Door

(P) Solid Overlay Door (no handle)

(F) Frame Glass Overlay Door (no handle)

"A"

"B"

"C"

"D"

"E"

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

Not all recessed outlet boxes will work for this applica-

tion as they are too narrow, but a recessed outlet box

equivalent to Arlington #DVFR1W is recommended for

this application, (see Figure 10).

PRODUCT DIMENSIONS

Figure 9

Figure 9a

Figure 10

9

"F"

21

1

⁄2"

(54.6 cm)

* Depth dimension of rough-in opening may vary depend-

ing on each individual installation. To recess entire door "F"

dimension plus 1" (2.5 cm) for thickness of power cord plug

is required.

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

APPLIES TO THE FOLLOWING MARVEL MODELS

ML15BC MA24BC

ML15RA MA24BR

MA24RA

ML24BC

ML24BR

ML24RA

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

ML15**(G) or (S) 115V/60Hz/15A

105 lbs

(47.7 kg)

ML15**(P) or (F) 115V/60Hz/15A

105 lbs

(47.7 kg)

ML24**(G) or (S) 115V/60Hz/15A

140 lbs

(63.6 kg)

ML24**(P) or (F) 115V/60Hz/15A

140 lbs

(63.6 kg)

MA24**(G) or (S) 115V/60Hz/15A

140 lbs

(63.6 kg)

MA24**(P) or (F) 115V/60Hz/15A

140 lbs

((63.6 kg)

"D"

"E"

"H"

"J"

"G"

PRODUCT DIMENSIONS

Figure 11

!

WARNING

Floor mount Anti-tip Bracket must be installed for freestand-

ing applications. Not required for built in applications.

10

USING YOUR ELECTRONIC CONTROL

Power Failure

Temp

Minus

keypad

Temp

Plus

keypad

On/Off

keypad Display Area

Lights keypad

(glass door

only)

Lock

keypad

System Status

indicators

Figure 12

Electronic single zone control

Starting your appliance:

Plug the appliance power cord into a 115 volt wall outlet.

Your appliance is shipped from the factory in the "On" posi-

tion and will begin start-up of cooling as soon as power is

supplied. If the appliance does not start, conrm that the

wall outlet has power, and that the control is in the "On"

position, (See "Turning your appliance On and Off" below).

The control display is covered with a clear plastic lm. This

lm may be removed by carefully lifting the lm at a corner.

On initial power up, the control display will indicate a

"Power Failure" alarm. This is a normal condition as the ap-

pliance was powered-up at the factory for quality inspection

and then removed from power. A momentary press of the

"On/Off" keypad will reset this alarm condition. (See Alarms

section on page 12).

Turning your appliance ON and OFF:

If the appliance is "On", (and out of sleep mode) the tem-

perature will be shown in the display area of the control.

To turn the appliance "Off", press and hold the "On/Off"

keypad for 4-seconds. "OFF" will now be displayed on the

control.

To turn the appliance "On", press and hold the "On/Off"

keypad for 4-seconds.

Sleep mode:

If no keypads are pressed for 60 seconds, the display will

enter sleep mode to conserve power. The control panel will

go dark with the exception of the system status "OK" indi-

cator which will remain enabled. Alarm conditions will wake

the display, (see alarms on page 12).

To make the following changes to the control settings

(turning the appliance ON/OFF, adjusting the tempera-

ture, changing the interior lights, and activating vaca-

tion mode), the control must be awake.

The sleep mode can be disabled if you prefer to have the

display on continuously. Press and hold the "Lock" key-

pad until the display goes past "Loc" and reads "nSL". To

enable the sleep mode, repeat the instruction, again going

past "Loc" until the display reads "SLP".

To wake the display press any keypad. A conrm tone will

sound, and the current storage compartment temperature

will be displayed.

ALARM RESET

11

USING YOUR ELECTRONIC CONTROL

Interior display lighting: (Glass door models only)

Your appliance is equipped with a dual light level display

lighting feature. With the control out of sleep mode press

the "Light" keypad once to activate the interior lighting

display feature at full illumination. A conrmation tone will

sound, and the light bulb "Icon" will illuminate. Pressing

the "Light" keypad a 2nd time will dim the lighting to 50%.

A 3rd press will deactivate the display lighting feature. The

display lighting will automatically deactivate after 4-hours.

Temperature mode:

The temperature mode is preset from the factory in Fahren-

heit (°F) but you have the option to change it to Centigrade

(°C). To change the mode, press and hold the "-" keypad,

while pressing the "+" keypad, then release the "-" keypad.

The temperature will now be displayed in Centigrade (°C).

Repeat the procedure to change the temperature mode

back to Fahrenheit (°F).

Control lock:

The control panel can be locked to avoid unintentional

changes. To lock the control, press and hold the "Lock" key-

pad until the display reads "Loc" then release your nger

from the keypad. The lock icon will ash 3-times and then

continuously illuminate. When the control panel is locked,

only the Lock keypad, System Status OK indicator, and

the Alarm indicator are active. To un-lock the control panel,

repeat this instruction until the display reads "nLc".

Adjusting the temperature:

To set or check the set-point temperature (with the control

out of sleep mode), press the "-" or "+" keypads. "SET" will

be indicated on the user interface panel and the current

set-point temperature will display and ash. Subsequent

presses of the "-" or "+" keypads will adjust the temperature

colder or warmer respectively. When you have reached

your desired set-point temperature, press the "On/Off" key-

pad to accept, or do nothing and the "Set" mode will time-

out in 10-seconds accepting the displayed temperature as

the new set-point.

The available set-point temperature range for your ap-

pliance is 34°F (1.2°C) to 42°F (5.7°C). If you attempt to

adjust the temperature outside of this range you will receive

an audible notication.

When initially loading your product with warm contents, it

may take up to 48-hours for the storage compartment tem-

perature to stabilize.

When making temperature set-point changes, it may take

up to 24-hours for the stored contents to stabilize at your

new set-point temperature.

Factors that affect the storage compartment stabilized

temperature:

• Changes to temperature setting.

• Room temperature changes.

• Temperature of stored contents.

- Loading warm contents.

- Cold content load will delay the change to a warmer

set-point temperature.

- Warm content load will delay the change to a colder

set-point temperature.

• Usage, (number and duration of the door openings).

• Use of the storage compartment display lighting, (glass

door product only).

• Installation of the appliance in direct sunlight or next to

a heat source.

12

USING YOUR ELECTRONIC CONTROL

ALARM RESET

Power Failure

• Power failure - If power to the appliance is inter-

rupted the System Status indicator will turn-off and

the "Power Failure" indicator will ash. Additionally, an

"ALARM RESET" indicator will be displayed below the

"On/Off" keypad. No audible tone will sound. This alarm

condition can be reset by momentarily pressing the

"On/Off" keypad. If this alarm occurs, it is recommend-

ed that you check the condition of any perishables,

even if the appliance is operating normally and the tem-

perature has recovered, as prolonged power outages

could result in excessive temperature excursions which

may spoil perishables.

• Temperature alarm - If the storage compartment

temperature exceeds 10°F from set-point for more than

a 1-hour duration, the System Status indicator will turn

off, the "Temp" indicator will ash, and an audible tone

will sound every 60-seconds. Additionally, an "ALARM

RESET" indicator will be displayed below the "On/Off"

keypad. This alarm condition can be reset by momen-

tarily pressing the "On/Off" keypad. If this alarm occurs

it is recommended that you check the condition of your

stored contents, even though the appliance is operating

normally and the temperature has recovered, as pro-

longed temperature excursions could spoil perishables.

ALARM RESET

Temp

NOTE

Door Ajar

Temp

Multiple alarms are possible, i.e.- "Door Ajar" for a pro-

longed period may trigger a "Temp" alarm, in which case

both "Door Ajar" and "Temp" indicators will activate.

Door Ajar

ALARM RESET

• Door ajar - If the door is open, or not closed prop-

erly, for more than 5-minutes the System Status OK

indicator will turn-off, the "Door Ajar" indicator will ash,

and a tone will sound every 60 seconds. Additionally,

an "ALARM RESET" indicator will be displayed below

the "On/Off" keypad. This alarm condition can be reset

by closing the door or momentarily pressing the "On/

Off" keypad, (i.e.-if you are cleaning the storage com-

partment, etc.). The alarm will recur in 5-minutes if the

alarm condition persists.

Alarms:

The control will alert you to conditions that could adversely

affect the performance of the appliance.

13

USING YOUR ELECTRONIC CONTROL

Vacation mode:

This operating mode can be used to save energy during

high cost energy periods, or when you won't be using your

appliance for an extended period of time by disabling the

lights, alarm tones, and keypad entry tones. Vacation mode

also serves as a Sabbath mode, disabling functions and

its controls in accordance with the weekly Sabbath and

religious holidays observed within the Orthodox Jewish

community. When used as Sabbath mode, you may open

or close the door at any time to access contents without

concern of directly turning on or off any lights, digital read-

outs, solenoids, fans, valves, compressor, icons, tones, or

alarms.

When activated, the display, alarm indicators and tones,

keypad touch tones, interior lights, and all options are dis-

abled. All keypad functions are disabled, with the exception

of the "On/Off" keypad which is required to exit Vacation-

mode. Storage compartment temperatures are monitored

and controlled at the settings prior to entering Vacation

mode.

To enter Vacation Mode (with the control out of sleep

mode), press and hold the "On/Off" keypad until the display

goes past "OFF" and reads "VAC". The display will ash

"VAC" 3-times to acknowledge your request, then will

display "VAC" continuously until Vacation mode is exited.

A power outage will not exit Vacation mode, exiting can

only be accomplished manually. To exit Vacation mode and

return to normal operation, press and hold the "On/Off"

keypad until the control displays the temperature.

14

OVERLAY DOOR PANEL INSTALLATION

!

WARNING

Overlay panel models are designed for use with built-

in installations only. Use in freestanding installations

could result in personal injury.

!

WARNING

The articulated hinges have many pinch points. Care-

fully close / collapse the hinges as soon as the door is

removed from the cabinet.

If you purchased an overlay panel model, your unit is

equipped with articulated hinges to allow fully integrated

built-in installations. Custom panel thicknesses of

5

⁄8" (15

mm) and

3

⁄4" (18 mm) are accommodated.

Figure 13

Figure 13b

Bottom of

door

Figure 13a

Loosen (do not remove ) these

2 phillips head screws on the

top and bottom hinges

Step 1: Removing the Door

With a phillips screwdriver remove the screw and "P" clamp

from the bottom of the door near the hinge. See Figure 13b.

Disconnect the door wire harness by pressing and holding

down the locking tab on the wire connector and pulling the

connector apart. See Figure 14.

Open the door and loosen the screws holding the hinges to

the cabinet (2 at the top and 2 at the bottom hinge). Do not

remove the screws but loosen them enough so the hinges

can be slipped off of the screws when sliding the door to

the side.

With a helper, and being careful not to scratch the cabinet

or the door, slide the door to the side about

1

⁄2 inch and

remove the hinges and door from the unit.

"P" clamp

and screw

Wire connector

see Figure 14

Cabinet

"Z" Bracket

!

WARNING

Use extreme caution with the articulated hinges. The

hinge is self closing and many pinch points exist prior

to built-in installation. Do not remove the cabinet "Z"

bracket from the top of the cabinet.

!

CAUTION

It is important to use the factory provided grille that came

with the product to assure proper air ow is maintained

through the condenser. The use of a custom grille is not

recommended and will void the warranty.

15

Step 2: Remove the door gasket

With the door laying on a at surface and starting at a

corner of the door remove the magnetic door gasket from

the interior side of the door, see Figure 15. Set the gasket

aside on a at surface.

There are 10 holes in the gasket retainer extrusions, (3 on

each side and 2 at the top and bottom which are used to

fasten the panel to the front of the door. The screws are

provided in the literature pack along with the door lock,

which is provided on certain models.

Figure 14

Press and hold down this

tab on the wire connec-

tor and pull the connector

apart.

Figure 15

Figure 15a

Overlay panel

ush with top

of door.

Holes in

gasket

retainer.

Magnetic Gasket

remove starting at a

corner, grasp and pull

away from the door.

OVERLAY DOOR PANEL INSTALLATION

Step 3: Cut and drill the overlay panel

Depending on your model cut the overlay door panel to the

dimensions shown in Figures 16 to 23. Also see Table "D"

for the height dimension and door styles. The window cut

out is for glass door models only. If your appliance has a

lock also drill the lock hole in the panel, see Figure 25.

Overlay panel to

be centered on

width of door.

16

Clearance for

screw head,

4 places

Clearance

for hinge

2 places

Figure 18

Right Hand Hinged Door

15" (38.1 cm) wide appliance

OVERLAY DOOR PANEL INSTALLATION

Figure 19

Right Hand Hinged Door

15" (38.1 cm) wide appliance

Clearance for

screw head,

4 places

Clearance

for hinge

2 places

Figure 16

Left Hand Hinged Door

15" (38.1 cm) wide appliance

Figure 17

Left Hand Hinged Door

15" (38.1 cm) Wide Appliance

4

7

⁄8"

(12.4 cm)

3

27

⁄32"

(9.8 cm)

1

3

⁄16"

(3 cm)

3

1

⁄8"

(7.9 cm)

1

⁄2"

(3.8 cm)

typical

Hinge side of door

Top of door

14

3

⁄4"

(37.5 cm)

1

⁄4" (6 mm)

Deep

5"

(12.7 cm)

1" (25.4 mm) diameter

counter bore

1

⁄4" (6 mm)

deep 4 places.

1

3

⁄4"

(4.4 cm)

"A"

(See Table D)

3

1

⁄8"

(7.9 cm)

Minimum

2"

(5.1 cm)

3

11

⁄16"

(9.4 cm)

4

1

⁄8"

(10.5 cm)

Minimum

3

1

⁄8"

(7.9 cm)

Minimum

1

⁄4" (6 mm)

radius is

permissible

1

11

⁄16"

(4.3 cm)

4

7

⁄8"

(12.4 cm)

3

27

⁄32"

(9.8 cm)

1

3

⁄16"

(3 cm)

3

1

⁄8"

(7.9 cm)

1

⁄2"

(3.8 cm)

typical

1

11

⁄16"

(4.3 cm)

Hinge side of door

14

3

⁄4"

(37.5 cm)

1

⁄4" (6 mm)

Deep

5"

(12.7 cm)

1" (25.4 mm) diameter

counter bore

1

⁄4" (6 mm)

deep 4 places.

1

3

⁄4"

(4.4 cm)

"A"

(See Table D)

3

1

⁄8"

(7.9 cm)

Minimum

2"

(5.1 cm)

3

11

⁄16"

(9.4 cm)

4

1

⁄8"

(10.5 cm)

Minimum

3

1

⁄8"

(7.9 cm)

Minimum

This side

facing interior

This side

facing interior

1

⁄4" (6 mm)

radius is

permissible

1

5

⁄32"

(2.9 cm)

1

5

⁄32"

(2.9 cm)

17

Figure 21

Left Hand Hinged Door

24" (61 cm) wide appliance

!

CAUTION

OVERLAY DOOR PANEL INSTALLATION

Weight of overlay door panel must not

exceed 15 pounds (6.8 kg) for a solid

door model or 10 pounds (4.5 kg) for a

glass door model.

Figure 23

Right Hand Hinged Door

24" (61 cm) wide appliance

23

3

⁄4"

(60.3 cm)

1" (2.5 cm) diameter

x

1

⁄4" (6 mm) deep

4 places

4

7

⁄8"

(12.4 cm)

3

27

⁄32"

(9.8 cm)

1

3

⁄16"

(3 cm)

14"

(35.6 cm)

1

⁄4" (6 mm)

radius is

permissible

3

1

⁄8"

(7.9 cm)

1

3

⁄4"

(4.4 cm)

3

1

⁄8"

(7.9 cm)

3

1

⁄8"

(7.9 cm)

"A"

(See Table D)

2"

(5.1 cm)

3

11

⁄16"

(9.4 cm)

4

1

⁄8"

(10.5 cm)

1

⁄2"

(3.8 cm)

typical

1

⁄4"

(6 mm)

Deep

1

11

⁄16"

(4.3 cm)

Hinge side of door

Top of door

Clearance for hinge

at top and bottom

Clearance for hinge

at top and bottom

Clearance for

screw head,

4 places

Figure 20

Left Hand Hinged Door

24" (61 cm) wide appliance

23

3

⁄4"

(60.3 cm)

1" (2.5 cm) diameter

x

1

⁄4" (6 mm) deep

4 places

4

7

⁄8"

(12.4 cm)

3

27

⁄32"

(9.8 cm)

1

3

⁄16"

(3 cm)

14"

(35.6 cm)

1

⁄4" (6 mm)

radius is

permissible

3

1

⁄8"

(7.9 cm)

3

1

⁄8"

(7.9 cm)

3

1

⁄8"

(7.9 cm)

1

3

⁄4"

(4.4 cm)

"A"

(See Table D)

2"

(5.1 cm)

3

11

⁄16"

(9.4 cm)

4

1

⁄8"

(10.5 cm)

1

⁄2"

(3.8 cm)

typical

1

⁄4"

(6 mm)

Deep

1

11

⁄16"

(4.3 cm)

Hinge side of door

Top of door

Clearance for

screw head,

4 places

Figure 22

Right Hand Hinged Door

24" (61 cm) wide appliance

This side

facing interior

This side

facing interior

1

5

⁄32"

(2.9 cm)

1

5

⁄32"

(2.9 cm)

18

OVERLAY DOOR PANEL INSTALLATION

Step 4: Assemble the panel to the door

The preferred method of attaching the panel to the door

is to clamp the panel to the door so it cannot move while

drilling the screw pilot holes. Use bar clamps or "C" clamps

with pads on the clamping surfaces that will not mar the

panel or the door. The custom overlay panel should be

ush with the top of the door and centered along the width

of the door. See Figure 15a. Drill holes through the gasket

extrusion using the 10 holes as pilot holes. Use the drill

size from the chart in Table "C", being careful not to drill

through the front surface of the panel. If the overlay panel is

thinner than

5

⁄8" (16 mm) thick shorter screws will have to be

obtained. Fasten the panel to the door with the 10 screws

provided in the literature pack. (See Figure 25a). Remove

the clamps and replace the gasket in the gasket extrusion

channels of the door. Some force may be required to seat

the gasket into the channels. Be sure the gasket corners

are seated properly.

MODEL

DOOR

DESCRIPTION DIM "A"

ML15RAP*RP Solid, Right Hand

30

11

⁄32" (77.1 cm)

ML15RAP*LP Solid, Left Hand

ML15BCF*RP Glass, Right Hand

ML15BCF*LP Glass, Left Hand

ML15BCP*RP Solid, Right Hand

ML15BCP*LP Solid, Left Hand

ML24RAP*RP Solid, Right Hand

ML24RAP*LP Solid, Left Hand

ML24BRF*RP Glass, Right Hand

ML24BRF*LP Glass, Left Hand

ML24BRP*RP Solid, Right Hand

ML24BRP*LP Solid, Left Hand

MA24BRF*RP

Glass, Right Hand

with Lock

27

23

⁄32" (70.4 cm)

MA24BRF*LP

Glass, Left Hand

with Lock

MA24RAP*RP

Solid, Right Hand

with Lock

MA24RAP*LP

Solid, Left Hand

with Lock

Table C

Table D

Material Type #10 Wood Screw

Hardwood

1

⁄8" (3.2 mm) Diameter. Pilot Hole

Softwood

7

⁄64 (2.8 mm) Diameter. Pilot Hole

19

Step 5: Assemble lock parts

Two (2) lock extensions are provided with the lock. Use

the longer extension for

3

⁄4" thick overlay panels and the

shorter one for

5

⁄8" thick overlay panels. Assemble the lock

extension, cam stop washer, spring washer, and set screw

to the lock as shown in Figure 24 and 26.

Install this lock assembly into the lock hole in the overlay

panel and secure with the retaining nut on the back side

with a 15 mm socket and ratchet. Make sure the key slot in

the front of the lock is vertical.

OVERLAY DOOR PANEL INSTALLATION

17

⁄32"

(13.7 mm)

3

1

/2"

(89 mm)

1

⁄2" (13 mm) diameter drill

through door panel, from

other side (see detail

above)

13

⁄16" (20.5 mm)

counter bore,

7

⁄16" (11 mm)

deep.

Hinge side of door

Counter bore

lock hole

on back side.

Step 6: Install lock cam

Attach the lock cam to the back of the lock assembly with

the phillips head screw provided. Orient the lock cam verti-

cally when installing on the lock.

SECTION A-A

SCALE 1 : 1

LOCK

NUT

BRASS EXTENSION

CAM

PHILLIPS SCREW

13/16 COUNTER

BORE 7/16 DEEP

1/2 HOLE

3/4 INCH

WOOD PANEL

SPRING WASHER

INNER

DOOR

Figure 24

Figure 25a

#10 x 1/2"

screw

Figure 25

20

OVERLAY DOOR PANEL INSTALLATION

Step 8: Secure the cabinet

Use the #8 x

3

⁄4" black screws from the literature pack to

secure the counter top to the cabinet top through the holes

in the cabinet "Z" bracket.

Cabinet

"Z" bracket

#8 x

3

⁄4" black

screws

(3 places)

Figure 27

Step 7: Install the door

Carefully open the top and bottom hinges on the door being

careful as there are many pinch points. Place the hinges

over the 4 screws in the cabinet, 2 at the top and 2 at the

bottom and slide the door into position. Tighten the 4 hinge

screws with a phillips screwdriver. (See Figures 13 and

13a). Place wire harness from the grille and mount to the

bottom of the door with the screw and "P" clamp removed

in step 1. (See Figure 13b). Reconnect the wire harness,

(See Figure 14).

Figure 26

Cam stop

washer

Spring

washer

Cam

Set screw

Lock

Key

Retainer

nut

Screw

Brass extension

(2 lengths provided

21

Figure 28

Figure 29

Figure 30

Figure 31

Figure32

SHELVING CONFIGURATIONS

Beverage Center:

Beverage Refrigerator:

Refrigerator:

Loading Tips and Suggestions

Your appliance is equipped with a cantilever shelf system

which provides maximum adjust ability and customizing of

the shelving arrangements listed below.

15" (38.1 cm) Wide Models:

Shown with a glass door. Figure 28.

15" (38.1 cm) Wide Models:

Shown with a solid door. Figure 31.

24" (61 cm) Wide Models:

Shown with a glass door. Figure 29.

24" (61 cm) Wide Models:

Shown with a glass door. Figure 30.

(2) wine cutout and at

glass cantilever shelf.

(See Figure 37).

(1) half depth roll-out

4 bottle wine shelf.

(2) frame and at glass cantile-

ver shelves. (See Figure 36).

(1) half width at glass can-

tilever shelf. (See Figure 35).

(1) wine cutout and at glass

cantilever shelf. (See Figure 37).

(1) frame and at glass crisper

cover.

(1) roll-out crisper pan

(2) frame and at glass cantile-

ver shelves. (See Figure 36).

24" (61 cm) Wide Models:

Shown with a solid door. Figure 32.

(2) perforated metal

cantilever shelves.

(See Figure 34).

Page is loading ...

AGA marvel ML15BC User manual

AGA marvel ML15BC User manual

in other languages

Related papers

Other documents