AGA marvel Marvel 80RF Troubleshooting guide

AGA marvel
Brand
AGA marvel
Model
Marvel 80RF
Category
Fridges
Type
Troubleshooting guide

This manual is also suitable for

Installaon
Operaon
and
Maintenance
Instrucons
Refrigerator / Freezer Models
61RF
80RF
CONTENTS
Unpacking your refrigerator........................
.........
..................
Removing the packaging......................
............
...................
Warranty Registraon.....................
.................
....................
Installing your refrigerator........................
.
..........
.
..................
Selecng the locaon..........................
.............
..................
Cabinet Clearances..................................
.........
...................
Leveling legs......................................
.............
.....................
Electrical Connecon ..........................
...........
...................
Using Your Refrigerator..................................
.......
.................
Seng the temperature control..............
...........
.................
Defrosng instrucons........
....
.............
..............
.................
Dimensions For Models 61RF Solid Door............
..
.................
Recommended Rough in Opening Dimensions
For Models 61RF Solid Door.................................................
Dimensions For Model 61RF Solid Overlay Door
....
...............
Recommended Rough in Opening Dimensions
For Model 61RF Solid Overlay Door.
...................
.................
Dimensions For Model 80RF Solid Door...............
.
.................
Recommended Rough in Opening Dimensions
For Model 80RF Solid Door..
.
.................
............
.................
Dimensions For Model 80RF Solid Overlay Door
.....
..............
Recommended Rough in Opening Dimensions
For Model 80RF Solid Overlay Door.
............
........................
Full Overlay Panel Installaon Instrucons....
.........
..............
Energy Saving Tips ................................................................
Care and Cleaning...................................
..........
.....................
Troubleshoong Guide.........................
...........
.......................
Obtaining Service...............................
.......
.........
....................
Household Product Warranty................
...............
..................
Important Safety Instrucons
Warnings and safety instrucons appearing in this guide are not
meant to cover all possible condions and situaons that may
occur. Common sense, cauon, and care must be exercised when
installing, maintaining, or operang this appliance.
Recognize Safety Symbols,
Words, and Labels.
WARNING-Hazards or unsafe pracces which could result in
personal injury.
CAUTION-Hazards or unsafe pracces which could result in
personal injury or property or product damage.
NOTE
NOTE-Important informaon to make a problem free installa-
on.
3
3
3
4
4
4
4
5
5
5
5
6
6
7
7
8
8
9
9
10
13
13
14
14
15
2
is commied to building a quality product
in an environmentally friendly manner. Our processes are ghtly
controlled and closely monitored. We have achieved cercaons
in ISO 9001 for quality assurance, ISO 14001 for environmental
management, and OHSAS 18001 for occupaonal health and safe-
ty from Lloyd’s Register Quality Assurance.
UNPACKING YOUR REFRIGERATOR
Remove Packaging
Your refrigerator has been packed for shipment with all parts
that could be damaged by movement securely fastened. Cut
the banding material at the boom of the carton, unfold the
carton at the boom and remove the carton from the appliance.
Remove the plasc bag, styrofoam corner posts and any tape
holding the door closed and internal components in place. The
owners manual is shipped inside the refrigerator in a plasc bag
along with the warranty registraon card.
Important
Keep your carton packaging unl your refrigerator has been
thoroughly inspected and found to be in good condion. If there
is damage, the packaging will be needed as proof of damage in
transit. Aerwards please dispose of all items responsibly in
parcular the plasc bags which can be a suocaon hazard.
Note to Customer
This merchandise was carefully packed and thoroughly inspected
before leaving our plant. Responsibility for its safe delivery
was assumed by the retailer upon acceptance of the shipment.
Claims for loss or damage sustained in transit must be made to
the retailer.
DO NOT RETURN DAMAGED MERCHANDISE TO THE MANUFAC-
TURER - FILE THE CLAIM WITH THE RETAILER.
Help Prevent Tragedies
Child entrapment and suocaon are not problems of the past.
Junked or abandoned refrigerators are sll dangerous - even if
they sit out for “just a few days”.
If you are geng rid of your old refrigerator, please follow the
instrucons below to help prevent accidents.
Before you throw away your old refrigerator or freezer:
• Take o the doors or remove the drawers.
• Leave the shelves in place so children may not easily climb
inside.
If the unit was shipped or has been laying on its back for any
period of me allow the refrigerator to sit upright for a period of
at least 24 hours before plugging in. This will assure oil returns
to the compressor. Plugging the refrigerator in immediately may
cause damage to internal parts.
It is important you send in your warranty registraon card im-
mediately aer taking delivery of your refrigerator.
The following informaon will be required when registering your
unit.
Model Number
Serial Number
Date of Purchase
Dealer’s name and address
The model number and serial number can be found on the serial
plate which is located inside the cabinet on the le side near the
top. See gure 1.
Warranty Registraon
NOTE
3
Figure 1
INSTALLING YOUR REFRIGERATOR
Leveling Legs
Front Grille, keep
this area open.
Figure 2
Select Locaon
The proper locaon will ensure peak performance of your ap-
pliance. We recommend a locaon where the unit will be out
of direct sunlight and away from heat sources. To assure your
product performs to specicaons the recommended installaon
locaon temperature range is from 65 to 90°F (18 to 32°C).
Cabinet Clearance
Venlaon is required from the boom front secon of the unit.
Keep this area open and clear of any obstrucons. Adjacent
cabinets and counter top can be installed around the unit as long
as the grille and door access remain unobstructed.
Figure 3
Rear of unit
with access
cover removed
Rear leveling legs
at outside corners
Center rear leveling
leg on 30” wide units
only
Leveling Legs
Adjustable legs at the front and rear corners of the unit should
be set so the unit is rmly posioned on the oor and level from
side to side and front to back. The overall height of your Marvel
refrigerator may be adjusted from 33-3/4” (85.7cm) with the lev-
eling legs turned in, and up to 34-3/4” (88.3cm) with the leveling
legs extended. The 30” wide product (80RF) have a center leg
at the rear of the cabinet that must also be used to stabilize the
cabinet. (See Figure 3).
To adjust the leveling legs, place the refrigerator on a solid
surface and protect the oor beneath the legs to avoid scratch-
ing the oor. With the assistance of another person, lean the
refrigerator back to access the front leveling legs. Raise or lower
the legs to the required dimension by turning the legs. Repeat
this process for the rear by lng the refrigerator forward using
cauon to keep the door from opening. On a level surface check
the refrigerator for levelness and adjust accordingly.
The front grille (toe kick) screws may be loosened and adjusted
to the desired height. When adjustment is complete ghten the
two toe kick screws. (See Figure 4).
4
Front Grille
Do not obstruct the front grille. The openings within the front
grille allow air to ow through the condenser heat exchanger.
Restricons to this air ow will result in increased energy usage
and loss of cooling capacity. For this reason it is important this
area to not be obstructed and the grille openings kept clean.
AGA MARVEL does not recommend the use of custom made
grilles as air ow may be restricted because of inadequate open-
ings. (See Figure 2).
• Do not splash or spray water from a hose on the refrigera-
tor! Doing so may cause an electrical shock, which may
result in severe injury or death.
• This unit should not, under any circumstances, be installed
to an un-grounded electrical supply.
Electrical Connecon
A grounded 115 volt, 15 amp dedicated circuit is required.
This product is factory equipped with a power supply cord that
has a three-pronged, grounded plug. It must be plugged into a
mang grounding type receptacle in accordance with the Na-
onal Electrical Code and applicable local codes and ordinances
(see Figure 5). If the circuit does not have a grounding type re-
ceptacle, it is the responsibility and obligaon of the customer to
provide the proper power supply. The third ground prong should
not, under any circumstances, be cut or removed.
Figure 5
Do not use an extension cord with
this appliance.
USING YOUR REFRIGERATOR
Seng the temperature control:
Inially set the cold control midway between the numbers
(between the #3 and #4).Aer at least 2 hours adjust to the
temperature that suits you. The higher the number you select,
the cooler the temperature. (See gure 6). Aer loading the
refrigerator allow at least 24 hours for your refrigerator to reach
a new temperature seng.
Defrosng instrucons:
Never use a scraper or any tool that might scratch or pierce the
cooling plate. Follow these steps whenever 1/4” or more of frost
accumulates:
1) Disconnect the power cord and set the cold control knob
to the “OFF” posion.
2) Remove contents.
3) Place pans of hot water on the cooling plate if you wish
to speed up defrosng.
4) Wipe out the interior and replace contents.
5) Connect power cord to outlet.
6) Set temperature control to desired level.
Figure 4
Toe kick (Front Grille)
Toe kick screw
5
Cold control
underneath door
in grille
Figure 6
Ground Fault Circuit Interrupters (GFCI) are prone to nuisance
tripping which will cause the unit to shut down. GFCI’s are gener-
ally not used on circuits which power equipment that must run
unaended for long periods of me, unless required to meet
local building codes and ordinances.
NOTE
The unit must be installed according to your local building codes
and ordinances.
RECOMMENDED ROUGH IN OPENING DIMENSIONS, MODELS 61RF SOLID DOOR
*24” (61 cm)
standard cabinet
depth
* Depth dimension may vary depending on
each individual installaon.
Electrical Requirements: A grounded 115 volt, 15 amp dedi-
cated circuit is required.
Power outlet can be located in the back wall behind unit. Add
1” to depth for thickness of plug, or recess outlet 1” into the
wall. Power outlet can also be installed in adjacent cabinetry
with a cutout for roung of power cord. Follow all local build-
ing codes when installing electrical and unit.
Product weight = 120 lbs. (54.5 kg.)
24” (61 cm)
DIMENSIONS FOR MODELS 61RF SOLID DOOR
3” to 4”
7.62 to 10.2cm)
33-3/4” to 34-3/4”
85.7 to 88.3cm)
23-7/8”
(60.66cm)
22”
(55.8cm)
24-1/16”
(61.11cm)
26”
(66.04cm)
47”
(119.38cm)
6
Door needs to be opened to this
dimension to remove and/or
adjust the shelving
25-11/16”
(65.3cm)
20” (50.8cm)
** 34” to 35”
(86.36 to 88.9cm)
** Minimum rough in opening required is to be
larger than the adjusted height of the cabinet.
RECOMMENDED ROUGH IN OPENING DIMENSIONS, 61RF SOLID OVERLAY DOOR
*24” (61 cm)
standard cabinet
depth
* Depth dimension may vary depending on
each individual installaon.
Electrical Requirements: A grounded 115 volt, 15 amp dedi-
cated circuit is required.
Power outlet can be located in the back wall behind unit. Add
1” to depth for thickness of plug, or recess outlet 1” into the
wall. Power outlet can also be installed in adjacent cabinetry
with a cutout for roung of power cord. Follow all local build-
ing codes when installing electrical and unit.
Product weight = 120 lbs. (54.5 kg.)
24” (61 cm)
DIMENSIONS FOR MODEL 61RF SOLID OVERLAY DOOR
3” to 4”
7.62 to 10.2cm)
33-3/4” to 34-3/4”
85.7 to 88.3cm)
23-7/8”
(60.66cm)
22”
(55.8cm)
24-1/16”
(61.11cm)
46-27/32”
(119.02cm)
23-5/16”*
(59.21cm)
7
* To face of door with-
out custom panel
Door needs to be opened to this
dimension to remove and/or
adjust the shelving
22-7/8”
(58.1cm)
18-7/8” (48.0cm)
** 34” to 35”
(86.36 to 88.9cm)
** Minimum rough in opening required is to be
larger than the adjusted height of the cabinet.
*24” (61 cm)
standard cabinet
depth
* Depth dimension may vary depending on
each individual installaon.
Electrical Requirements: A grounded 115 volt, 15 amp dedicated
circuit is required.
Power outlet can be located in the back wall behind unit. Add 1” to
depth for thickness of plug, or recess outlet 1” into the wall. Power
outlet can also be installed in adjacent cabinetry with a cutout for
roung of power cord. Follow all local building codes when install-
ing electrical and unit.
Product weight = 135 lbs. (61.4 kg.)
30” (76.2 cm)
RECOMMENDED ROUGH IN OPENING DIMENSIONS, MODEL 80RF SOLID DOOR
DIMENSIONS FOR MODEL 80RF SOLID DOOR
3” to 4”
7.62 to 10.2cm)
33-3/4” to 34-3/4”
85.7 to 88.3cm)
22”
(55.8cm)
26”
(66.04cm)
24-1/16”
(61.11cm)
47”
(119.38cm)
29-7/8”
(75.9cm)
8
31-11/16”
(80.5cm)
** 34” to 35”
(86.36 to 88.9cm)
** Minimum rough in opening required is to be
larger than the adjusted height of the cabinet.
*24” (61 cm)
standard cabinet
depth
* Depth dimension may vary depending on
each individual installaon.
Electrical Requirements: A grounded 115 volt, 15 amp dedicated
circuit is required.
Power outlet can be located in the back wall behind unit. Add 1”
to depth for thickness of plug, or recess outlet 1” into the wall.
Power outlet can also be installed in adjacent cabinetry with a
cutout for roung of power cord. Follow all local building codes
when installing electrical and unit.
Product weight = 135 lbs. (61.4 kg.)
30” (76.2 cm)
DIMENSIONS FOR MODEL 80RF SOLID OVERLAY DOOR
RECOMMENDED ROUGH IN OPENING DIMENSIONS, 80RF SOLID OVERLAY DOOR
3” to 4”
7.62 to 10.2cm)
33-3/4” to 34-3/4”
85.7 to 88.3cm)
22”
(55.8cm)
24-1/16”
(61.11cm)
23-5/16”*
(59.21cm)
29-7/8”
(75.9cm)
46-27/32”
(119.02cm)
9
* To face of door with-
out custom panel
28-7/8”
(73.4cm)
** 34” to 35”
(86.36 to 88.9cm)
** Minimum rough in opening required is to be
larger than the adjusted height of the cabinet.
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Figure 7
Door should be
parallel to top
and sides of
refrigerator.
Step 2: Remove door
Remove the top hinge pin from the hinge with an 1/8” allen
wrench. Remove the door by angling the top of the door out-
ward and liing the door o the boom hinge.
(See detail in Figure 7).
Step 3: Remove gasket
Lay the door on its front being careful not to scratch it. Remove
the door gasket by peeling up and out of the channel.
Step 4: Cut overlay panel
Depending on the refrigerator model cut the overlay panel to the
dimensions shown in Figure 8 and Table A below.
Model W H
61RF
23-5/8”
(59.99cm)
30-5/16”
(76.99cm)
80RF
29-5/8”
(75.23cm)
30-5/16”
(76.99cm)
Table A
NOTE
NOTE
For overlay with lock opon panel thickness to be 3/4” (19mm)
maximum to 5/8” (16mm) minimum.
Weight of the overlay panel should not exceed 20 pounds (9.1
kilograms).
Hinge adapter bracket lo-
cated on the top and boom
of the door.
Remove top
hinge pin to re-
move the door.
9/32”
(7mm)
H
W
Front of
overlay
panel
Figure 8
10
Step 1: Verify door alignment
Verify that the door is aligned correctly with the cabinet prior
to fabricang the custom panel. Failure to do so may result in
mis-alignment of the custom panel with the hinge bracket. The
door should be parallel to the sides and top of the refrigerator.
If alignment is necessary the door may be adjusted by loosen-
ing the 2 screws which secure the upper and/or lower hinge
adapter brackets, located on the top and boom of the door,
and adjusng the door side to side. Use a 5/32” allen wrench for
this procedure. (See Figure 7 below). When nished aligning the
door, ghten the screws securely.
For the door to close properly, it is necessary to maintain a
minimum space of 9/32” (7mm) between the door and cabinet
ange (See Figure 7). This space can be adjusted by adjusng the
top and boom hinge adapter brackets.
Step 5: Drill hinge clearance holes in overlay panel
Set the overlay panel on the door front, align the edges, and
clamp together. Clamp the panel rmly but be careful not to
damage the door or the panel. Mark center of hinge adapter
hole on wood panel, top and boom. (See Figure 9.) Remove
wood panel from door and drill 5/16” (8mm) diameter clearance
holes into the overlay panels 3/4” (20mm) deep. These will be
clearance holes for the top and boom hinge pins.
This is also a convenient me to locate and drill the holes for
your handle. Most oen the handle is to match that of the sur-
rounding cabinetry. If your handle aaches from the back-side
of the custom panel, locate the mounng holes while the panel
is aached to the door and cabinet. Aer the panel is removed
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Material Type #8 Wood Screw
Hardwood 1/8” (3.2mm) Diameter. Pilot Hole
Sowood 7/64 (2.8mm) Diameter. Pilot Hole
Table B
If your refrigerator has a door lock proceed to Step 7. If your
refrigerator does not have a door lock proceed to Step 9.
NOTE
Step 7: Mark and drill lock hole.
Locate and mark with a pencil the locaon of the lock hole on
the overlay panel, this is the hole in the top corner of the handle
side of the door. Remove the clamp and remove the overlay
panel from the door. On the backside of the panel where you
marked the lock locaon drill a 13/16” (20.5mm) diameter
counter bore 7/16” (11.0mm) deep into the overlay panel. Drill a
15/32” (12.0mm) diameter hole through the overlay panel cen-
tered on the counter bore being careful not to splinter the wood
on the face side of the panel. (See Figure 11).
Figure 10
Top hinge
adapter
Hole in hinge
adapter
Door
Overlay
Panel
Hole in boom
hinge adapter
Figure 9
11
Step 6: Drill panel mounng holes
Re-clamp the panel to the door per step 5 and drill the screw
pilot holes for aaching the overlay panel to the door. Select
the size of the hole from Table B. Be careful not to drill the pilot
holes through the overlay panel, (1/2” (12.7mm) deep for 3/4”
(19mm) and 5/8” (15.7mm) panels ).
from the door, drill the mounng holes from the front, to the
recommended diameter of the handle manufacturer. Counter
bore the back-side of the panel so the screw heads do not inter-
fere with the surface of the door.
1.234” (31.3mm)
.991” (25.2mm)
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Step 9: Secure overlay panel to the door.
With the #10 wood screws provided fasten the overlay panel to
the door. (See Figure 13).
Step 10: Install lock cam (Models with locks only).
Aach the lock cam to the back of the lock assembly with the
phillips head machine screw provided. Orient the lock cam ver-
cally when installing on the lock.
Step 11: Install door gasket
Press the door gasket into the door channel. Make certain the
gasket corners are fully inserted. If applicable insert the key into
the lock and make certain the lock operates properly.
Step 12: Install the door
Install the top and boom hinge adapter bushings back into the
hinge adapters that were removed in step 6. Install the door by
reversing the procedure from step 2. Install the top hinge pin so
the screw head is ush with the top surface of the hinge. If appli-
cable insert key into lock and verify the lock cam works properly
with the catch bracket on the front of the refrigerator cabinet.
Top hinge pin
Top door hinge
adapter
Top hinge adapter
bushing
Top hinge
Boom door
hinge adapter
Boom hinge
adapter bushing
Boom hinge pin
Boom hinge
cam
Figure 12
Right hand
hinges shown
Clearance hole through
door gasket channel
#10 Wood Screw
Figure 13
Back of door
Figure 11
SECTION A-A
SCALE 1 : 1
LOCK
NUT
BRASS EXTENSION
CAM
PHILLIPS SCREW
13/16 COUNTER
BORE 7/16 DEEP
15/32 HOLE
3/4 INCH
WOOD PANEL
SPRING WASHER
INNER
DOOR
Step 8: Assemble the lock parts
Two (2) lock extensions are supplied with the lock. Use the lon-
ger extension for a 3/4” thick overlay panel and the shorter one
for a 5/8” thick panel. Assemble the lock extension, cam stop
washer, spring washer, and set screw to the lock as shown in
Figure 10 and 11. Install this assembly into the overlay panel and
secure with the retaining nut using a 15mm socket. Make sure
the key slot in the lock is vercal.
12
Boom
hinge
Condenser Air Flow
The condenser underneath the cabinet does not rquire frequent
cleaning; however, sasfactory cooling depends on adequate
venlaon over this heat exchanger. It is recommended to annu-
ally clean the condenser by vacuuming and brushing. To access
the condenser, the unit must be pulled out from the installaon,
and the lower machine compartment access cover removed.
Disconnect the power cord before cleaning the condenser.
Be sure that nothing obstructs the required air ow openings
in front of the cabinet. At least once or twice a year, brush or
vacuum lint and dirt from the front grille area (see page 4).
Cabinet
The painted cabinet can be washed with either a mild soap and
water and thoroughly rinsed with clear water. NEVER use abra-
sive scouring cleaners.
Interior
Wash interior compartment with mild soap and water. Do NOT
use an abrasive cleaner, solvent, polish cleaner or undiluted
detergent.
Care of Unit
1. Avoid leaning on the door, you may bend the door hinges or
p the unit.
2. Exercise cauon when sweeping, vacuuming or mopping
near the front of the unit. Damage to the grille can occur.
3. Periodically clean the interior of the unit as needed.
4. Periodically check and/or clean the front grille as needed.
Replacing the light bulb. (see Figure 14)
1. Unplug the power cord from the wall receptacle.
2. Open the cabinet door.
3. Remove the 3 screws on the front face of the light lens using
a phillips screwdriver.
4. Remove the lens.
5. Unscrew the exisng bulb and replace with an equivalent 15
wa, intermediate base appliance bulb. Do not replace with
a bulb higher than 15 was.
6. Reassemble parts and plug in power cord.
To clean the light assembly, disconnect the power cord and wipe
the assembly with a mildly damp cloth. Dry the unit completely
before connecng the power cord.
ENERGY SAVING TIPS AND CARE AND CLEANING
The following suggesons will minimize the cost of
operang your refrigeraon appliance.
1. Do not install your appliance next to a hot appliance, (cook-
er, dishwasher, etc.). heang air duct, or other heat sources.
2. Install product out of direct sunlight.
3. Assure the toe grille vents at front of unit beneath door is
not obstructed and kept clean to allow venlaon for the
refrigeraon system to expel heat.
4. Plug your appliance into a dedicated power circuit. (Not
shared with other appliances).
5. When inially loading your new product, or whenever large
quanes of warm contents are placed within refrigerated
storage compartment, minimize door openings for the next
12 hours to allow contents to pull down to compartment
set-point temperature.
6. Maintaining a relavely full storage compartment will re-
quire less appliance run me than an empty compartment.
7. Assure door closing is not obstructed by contents stored in
your appliance.
8. Allow hot items to reach room temperature before placing
in product.
9. Minimize door openings and duraon of door openings.
10. Use the warmest temperature control set-point that meets
your personal preference and provides the proper storage
for your stored contents.
11. When on vacaon or away from home for extended pe-
riods, set the appliance to warmest acceptable tempera-
ture for the stored contents.
12. Set the control to the “o” posion if cleaning the unit
requires the door to be open for an extended period of
me.
13. Annually clean condenser heat exchange coil located
in machine compartment underneath unit, (see “Care
and Cleaning” page 13).
13
Light
bulb
Figure 14
Light lens
TROUBLESHOOTING YOUR REFRIGERATOR
Problem Possible Cause Remedy
Unit not cold enough
Adjust temperatures (See “Set the
temperature control” on page 5)
• Control set too warm
• Content temperature not stabilized.
• Excessive usage or prolonged door
openings.
• Airow to front grille blocked.
• Door gasket not sealing properly.
• Adjust temperature colder. Allow 24 hours
for temperature to stabilize.
• Allow temperature to stabilize for at least 24
hours.
• Airow must not be obstructed to front
grille. See “clearances” on
page 4.
• Check door alignment and/or adjust or re-
place door gasket.
Unit too cold
Adjust temperatures (See “Set the
temperature control” on page 5)
• Control set too cold
• Door gasket not sealing properly.
• Adjust temperature warmer. (See page 5,
“set the temperature control”). Allow 24
hours for temperature to stabilize.
• Check door alignment and/or adjust or re-
place door gasket.
No interior light in compartments. • Light bulb burned out. • Replace light bulb.
Light will not go out when door is
closed
• Door not acvang light switch. • Verify cabinet is level, refer to page 4 for
leveling instrucons.
• Verify the door is aligned properly, refer to
page 10 for instrucons.
Noise or Vibraon • Unit not level • Level unit, see “Leveling Legs” on page 4.
Unit will not run. • Unit turned o
• Power cord not plugged in.
• No power at outlet.
• Turn unit on. See “Set the temperature con-
trol” on page 5.
• Plug in power cord.
• Check house circuit.
Before You Call for Service
If the unit appears to be malfunconing, read through this
manual rst. If the problem persists, check the troubleshoong
guide below. Locate the problem in the guide and refer to the
cause and its remedy before calling for service. The problem may
be something very simple that can be solved without a service
call. However, it may be required to contact your dealer or a
qualied service technician.
If Service is Required:
• If the product is within the rst year warranty period please
contact your dealer or call Marvel Customer Service at
800.223.3900 for direcons on how to obtain warranty
coverage in your area.
• If the product is outside the rst year warranty period,
Marvel Customer Service can provide recommendaons of
service centers in your area. A lisng of authorized service
centers is also available at www.agamarvel.com under the
service and support secon.
• In all correspondence regarding service, be sure to give the
model number, serial number, located on your products se-
rial plate, and proof of purchase.
• Try to have informaon or descripon of nature of the prob-
lem, how long the unit has been running, the room temper-
ature, and any addional informaon that may be helpful in
quickly solving the problem.
• Table C is provided for recording pernent informaon
regarding your product for future reference.
For Your Records
Date of Purchase
Dealer’s name
Dealer’s Address
Dealer’s City
Dealer’s State
Dealer’s Zip Code
Appliance Serial Number
Appliance Model Number
Date Warranty Card Sent (Must be
within 10 days of purchase).
Electrocuon Hazard - Never aempt to repair or perform
maintenance on the unit unl the main electrical power has
been disconnected. Turning the unit control “OFF” does not
remove electrical power from the units wiring.
14
Table C
Parts or Service
Not Supplied or Designated by Marvel
The above warranes also do not apply if:
• The original bill of sale, deliver date, or serial number can-
not be veried.
• Defecve parts are not returned for inspecon if so request-
ed by Marvel.
• The refrigeraon equipment is not in the possession of the
original end use purchaser.
The warranes set forth herein are the only warranes extended
by AGA Marvel. Any implied warranes, including the implied
warranty of merchantability, are limited to the duraon of these
express warranes. In no event shall AGA Marvel be liable for
any consequenal or incidental damages or expenses resulng
from breach of these or any other warranes, whether express
or implied.
Some states do not allow the exclusion or limitaon of conse-
quenal damages or a limitaon on how long an implied war-
ranty lasts, so the above exclusion or limitaon may not apply
to you. This warranty gives you specic legal rights and you may
have other rights that may vary from state to state.
No person, rm, or corporaon is authorized to make any other
warranty or assume any other obligaon for AGA Marvel. These
warranes apply only to products used in any of the y states
of the United States and the District of Columbia.
To obtain performance of this warranty, report any defects to:
1260 E. VanDeinse St.
Greenville MI 48838
Phone: 800.223.3900
Enre Product
Limited One Year Parts and Labor Warranty
AGA Marvel warrants that it will supply all necessary parts and
labor to repair or replace in the end user’s home or oce, any
component which proves to be defecve in material or work-
manship, subject to the condion and exclusions stated below,
for a period of one year from the date of purchase by the end
user.
Addional Second Through Fih Year
Limited Parts Only Warranty
During the four years following expiraon of the one year limited
warranty, AGA Marvel will supply replacement parts for the
hermecally sealed refrigeraon system which consists of the
compressor, condenser, drier, accumulator, bypass valve, con-
necng tubing and the evaporator that are proven to be defec-
ve due to workmanship or materials subject to the condions
and exclusions below.
The above warranes do not cover:
• Shipping costs of replacement parts or returned defecve
parts.
• Customer educaon or instrucons on how to use the appli-
ance.
• Any content loss due to product failure.
• Removal or installaon of product.
Nor do the above warranes cover failure of this product or its
components due to:
• Transportaon or subsequent damages.
• Commercial use or use other than normal household or
small oce.
• Improper installaon, misuse, abuse, accident or alteraon,
use of wiring not conforming to electrical codes, low or high
voltages, failure to provide necessary maintenance, or other
unreasonable use.
HOUSEHOLD PRODUCT WARRANTY
15
All specicaons and product designs subject to change without noce. Such revisions do not entle the
buyer to corresponding changes, improvements, addions, replacements or compensaon for previously
purchased products.
www.agamarvel.com
1260 E. VanDeinse St.
Greenville MI 48838
800.223.3900
41011769-EN Rev N
10/31/11
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

AGA marvel Marvel 80RF Troubleshooting guide

AGA marvel
Brand
AGA marvel
Model
Marvel 80RF
Category
Fridges
Type
Troubleshooting guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents