Axis Q6034 Installation guide

ENGLISH DEUTSCH

ITALIANO

ESPAÑOL

INSTALLATION GUIDE

FRAN

Ç

AIS

AXIS Q6034 PTZ Dome Network Camera

Legal Considerations

Video and audio surveillance can be prohibited by laws

that vary from country to country. Check the laws in

your local region before using this product for

surveillance purposes.

This product includes one (1) H.264 decoder license. To

purchase further licenses, contact your reseller.

Trademark Acknowledgments

Apple, Boa, Bonjour, Ethernet, Internet Explorer, Linux,

Microsoft, Mozilla, Netscape Navigator, OS/2, Real,

SMPTE, QuickTime, UNIX, Windows, WWW are

registered trademarks of the respective holders. Java

and all Java-based trademarks and logos are trademarks

or registered trademarks of Sun Microsystems, Inc. in

the United States and other countries. Axis

Communications AB is independent of Sun

Microsystems Inc. UPnP™ is a certification mark of the

UPnP™ Implementers Corporation.

Electromagnetic Compatibility (EMC)

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to

radio or television reception, which can be determined

by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or

more of the following measures: Re-orient or relocate

the receiving antenna. Increase the separation between

the equipment and receiver. Connect the equipment to

an outlet on a different circuit to the receiver. Consult

your dealer or an experienced radio/TV technician for

help. Shielded (STP) network cables must be used with

this unit to ensure compliance with EMC standards.

USA - This equipment has been tested and found to

comply with the limits for a Class B computing device

pursuant to Subpart B of Part 15 of FCC rules, which are

designed to provide reasonable protection against such

interference when operated in a commercial

environment. Operation of this equipment in a

residential area is likely to cause interference, in which

case the user at his/her own expense will be required to

take whatever measures may be required to correct the

interference.

Canada - This Class B digital apparatus complies with

Canadian ICES-003.

Europe - This digital equipment fulfills the

requirements for radiated emission according to limit B

of EN55022, and the requirements for immunity

according to EN55024 residential and commercial

industry.

Japan - This is a class B product based on the standard

of the Voluntary Control Council for Interference from

Information Technology Equipment (VCCI). If this is used

near a radio or television receiver in a domestic

environment, it may cause radio interference. Install and

use the equipment according to the instruction manual.

Australia - This electronic device meets the

requirements of the Radio communications

(Electromagnetic Compatibility) Standard AS/NZS

CISPR22:2002.

Korea - Class B: As this equipment has obtained EMC

registration for household use, it can be used in any area

including residential areas.

Safety

Complies to EN 60950-1 (IEC 60950-1), Safety of

Information Technology Equipment.

Equipment Modifications

This equipment must be installed and used in strict

accordance with the instructions given in the user

documentation. This equipment contains no

user-serviceable components. Unauthorized equipment

changes or modifications will invalidate all applicable

regulatory certifications and approvals.

Liability

Every care has been taken in the preparation of this

document. Please inform your local Axis office of any

inaccuracies or omissions. Axis Communications AB

cannot be held responsible for any technical or

typographical errors and reserves the right to make

changes to the product and documentation without

prior notice. Axis Communications AB makes no

warranty of any kind with regard to the material

contained within this document, including, but not

limited to, the implied warranties of merchantability

and fitness for a particular purpose. Axis

Communications AB shall not be liable nor responsible

for incidental or consequential damages in connection

with the furnishing, performance or use of this material.

RoHS

This product complies with both the European

RoHS directive, 2002/95/EC, and the Chinese

RoHS regulations, ACPEIP.

WEEE Directive

The European Union has enacted a Directive

2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE Directive). This directive is

applicable in the European Union member

states. The WEEE marking on this product (see right) or

its documentation indicates that the product must not

be disposed of together with household waste. To

prevent possible harm to human health and/or the

environment, the product must be disposed of in an

approved and environmentally safe recycling process.

For further information on how to dispose of this

product correctly, contact the product supplier, or the

local authority responsible for waste disposal in your

area. Business users should contact the product supplier

for information on how to dispose of this product

correctly. This product should not be mixed with other

commercial waste.

Support

Should you require any technical assistance, please

contact your Axis reseller. If your questions cannot be

answered immediately, your reseller will forward your

queries through the appropriate channels to ensure a

rapid response. If you are connected to the Internet, you

can:

• download user documentation and firmware updates

• find answers to resolved problems in the FAQ database.

Search by product, category, or phrases

• report problems to Axis support by logging in to your

private support area

AXIS Q6034 Installation Guide Page 3

ENGLISH

Safeguards and Warnings

Please read through this Installation Guide carefully before installing the product. Keep the

Installation Guide for further reference.

Safety Notice - Battery replacement

This Axis product uses a 3.0V CR2032 Lithium battery as the power supply for its internal real-time clock (RTC).

Under normal conditions this battery will last for a minimum of 5 years. Low battery power affects the

operation of the RTC, causing it to reset at every power-up. A log message will appear when the battery needs

replacing. The battery should not be replaced unless required!

If the battery does need replacing, please contact www.axis.com/techsup for assistance.

• Danger of Explosion if battery is incorrectly replaced

• Replace only with the same or equivalent battery, as recommended by the manufacturer.

• Dispose of used batteries according to the manufacturer's instructions.

!

CAUTION!

• When transporting the Axis product, use the original packaging or equivalent to prevent

damage to the product.

• Avoid exposing the Axis product to vibration, shocks or heavy pressure and do not install the

camera on unstable brackets, unstable or vibrating surfaces or walls, since this could cause

damage to the product.

• Only use handtools when installing the Axis product, the use of electrical tools or excessive

force could cause damage to the product.

• Do not use chemicals, caustic agents, or aerosol cleaners. Use a damp cloth for cleaning.

• Only use accessories and replacement parts provided or recommended by Axis.

• Do not attempt to repair the product by yourself, contact Axis or your Axis reseller for service

matters.

!

IMPORTANT!

• To use this Axis product outdoors, it must be installed in an approved outdoor housing.

• This Axis product must be used in compliance with local laws and regulations.

• Store and transport the Axis product in a dry and ventilated environment.

Page 4 AXIS Q6034 Installation Guide

Cleaning of Dome Cover

Be careful not to scratch or damage the dome cover. Do not clean a dome cover that looks clean to

the eye and never polish the surface. Excessive cleaning can damage the surface.

For general cleaning of a dome cover it is recommended to use a non-abrasive, solvent-free neutral

soap or detergent with water and a soft cloth. Rinse well with clean lukewarm water. Dry with a

soft cloth to prevent water spotting.

Never use harsh detergents, gasoline, benzene or acetone etc. and avoid cleaning in direct sunlight

or at elevated temperatures.

AXIS Q6034 Installation Guide Page 5

ENGLISH

AXIS Q6034 Installation Guide

This installation guide provides instructions for installing an AXIS Q6034 PTZ Dome Network

Camera on your network. For all other aspects of using the product, please see the User’s Manual,

available on the CD included in this package, or from www.axis.com

Installation Steps

1. Check the package contents against the list below.

2. Hardware overview. See page 6.

3. Install the hardware.

• Prepare for installation, see page 8.

• Hard ceiling mount, see page 9.

• Drop ceiling mount, see page 10.

• Bracket mount (optional accessory), see page 12.

• Install the AXIS T8123 High PoE Midspan 1-port, see page 13.

4. Assign an IP address. See page 14.

5. Set the password. See page 17.

Package Contents

Item Models/variants/notes

Network camera AXIS Q6034

Dome covers Clear transparent cover (pre-mounted)

Smoked transparent cover

Mounting kit Mounting kit for hard ceilings and drop ceilings

High PoE Midspan AXIS T8123

CD AXIS Network Video Product CD, including product documentation,

installation tools and other software

Printed materials AXIS Q6034 Network Camera Installation Guide (this document)

Axis Warranty Document

Drill template

Extra serial number labels (2x)

AVHS Authentication key

Optional accessories AXIS T91A Mounting Accessories

Multi-connector cable for connection of I/O, audio, and power

See www.axis.com for information on power accessories and outdoor housings

Important!

This product must be used in

compliance with local laws and

regulations.

Page 6 AXIS Q6034 Installation Guide

Hardware Overview

SDHC card slot

Status indicator LED

Control button

Dome bracket

Dome cover

Dome ring

screw (4)

Dome ring

Camera unit

Dome cover

Power button

screw (4)

AXIS Q6034 Installation Guide Page 7

ENGLISH

Hard ceiling mount

Drop ceiling mount

Bracket arm (3)

Bracket arm

Mounting plate

screw (3) and

Plastic dome

Camera base lid

Multi-connector

Hook for safety wire

Network connector

Top cover screw (4)

Top cover

Unit holder (3)

cover

Mounting plate

screw (3)

Camera base lid screw (3)

Cable tracks

Foam gasket

Safety wire

Part number (P/N) & Serial number (S/N).

The serial number may be required during the

installation.

Bracket ring

washer (3)

Page 8 AXIS Q6034 Installation Guide

Install the hardware

The network camera can be mounted with the cables routed through or along the wall or ceiling.

Prepare for installation

Read all the instructions before preparing to install AXIS Q6034 since several installation

preparation steps require removing the dome ring and the dome cover must be removed and would

benefit from being completed together.

• The AXIS Q6034 is supplied with a clear transparent cover and a smoked transparent cover.

If required, follow the instructions

Replace the clear/smoked dome cover (optional)

, below

to replace the dome cover.

• A standard or high capacity SD card (not included) is required to store images locally in the

network camera. Follow the instructions

Install an SD card (optional)

, below to remove the

dome cover and install an SD card.

Replace the clear/smoked dome cover (optional)

1. Loosen the 4 dome ring screws and remove the dome ring and the dome cover, see illustration

on page 6.

2. Remove the 4 dome bracket screws and remove the dome bracket and the dome cover from the

dome ring.

3. Attach the dome bracket and the dome cover to the dome ring and tighten the 4 screws.

4. If installing an SD card, refer to the instructions

Install an SD card (optional)

, below.

5. Put the dome ring with the dome cover back in the original position and tighten the screws.

Note:

Be careful not to scratch or damage the dome cover. If possible, keep the protective plastic

on the dome cover until the installation is complete.

Install an SD card (optional)

1. Loosen the 4 dome ring screws and remove the dome ring and the dome cover, see illustration

on page 6.

2. Insert an SD card (not included) into the SDHC (Secure Digital High Capacity) card slot.

3. Put the dome ring with the dome cover back in the original position and tighten the screws.

Notes:

The SD card is automatically mounted when inserted into the SDHC card slot. However,

before removing the SD card it should be unmounted through the camera’s web pages. Go

to Setup > System Options > Storage > SD Card and click Unmount. For more informa-

tion, please see the User’s Manual available from the AXIS Network Video Product CD sup-

plied with this product or from the website at www.axis.com

!

IMPORTANT! - To use AXIS Q6034 outdoors, it must be installed in an approved

outdoor housing. Please see www.axis.com for more information on outdoor housing.

AXIS Q6034 Installation Guide Page 9

ENGLISH

Hard ceiling mount

1. Prepare the ceiling for installation of the mounting plate, use the supplied drill template to

position the holes. Make sure to use drill bits, screws, and plugs that are appropriate for the

material.

2. Install the mounting plate. The arrow on the mounting plate will align with the logotype on the

camera.

3. Loosen the 3 camera base lid screws and remove the camera base lid, see illustration on page 7.

4. Secure the camera using the supplied safety wire.

5. Route and connect the network cable and the multi-connector cable, if applicable, to the

network camera. Be careful not to damage the cables when connecting them. Make sure the

foam gasket holes are aligned with the cable tracks and, if applicable, remove the cut-out piece

for the multi-connector cable from the foam gasket.

6. Put the camera base lid back in its original position and fasten the screws.

7. Slide the unit holders on the network camera into the slots on the mounting plate and rotate

the camera unit.

8. Install the High PoE Midspan 1-Port, see

Install the AXIS T8123 High PoE Midspan 1-port,

on

page 13.

9. Check that the indicator LEDs on the midspan indicate the correct conditions, see the table on

page 23 for further details.

Mounting plate

Safety wire

Page 10 AXIS Q6034 Installation Guide

Drop ceiling mount

1. Remove the ceiling tile in which the drop ceiling mount is to be fitted.

2. Use the supplied template to mark the position for the 225 mm (8.9 in.) hole in the ceiling tile.

Cut around the template.

Notes:

• The combined weight of the camera and ceiling mount is approximately 3.2 kg (7.1 lb.). Check that

the ceiling material is strong enough to support this weight.

• The ceiling tile should be 5 mm–60 mm (0.2 in.–2.4 in.) thick.

3. Put the ceiling bracket into the ceiling tile, see illustration on page 11. Make sure the arrows on

the mounting plate and the ceiling bracket are pointing in the same direction for the logotypes

on the camera and the drop ceiling cover to align.

4. Tighten the bracket arm screws using a Torx 20 screwdriver head.

5. Loosen the 3 camera base lid screws and remove the camera base lid, see illustration on page 7.

6. Route and connect the network cable and the multi-connector cable, if applicable, to the

network camera. Be careful not to damage the cables when connecting them. Make sure the

foam gasket holes are aligned with the cable tracks and, if applicable, remove the cut-out piece

for the multi-connector cable from the foam gasket. Turn the cable holders to keep the cables

in place, see illustration below.

7. Put the camera base lid back in its original position and fasten the screws.

Ceiling tile

Hole diameter

225 mm (8.9 in.)

Multi-connector cable

Network cable

Cable holders

AXIS Q6034 Installation Guide Page 11

ENGLISH

8. Secure the camera using the supplied safety wire.

9. Slide the unit holders on the network camera into the slots on the mounting plate and rotate

the camera unit.

10. Install the High PoE Midspan 1-Port, see

Install the AXIS T8123 High PoE Midspan 1-port,

on

page 13.

11. Check that the indicator LEDs on the midspan indicate the correct conditions. See the table on

page 23 for further details.

12. Install the ceiling tile, with the camera mounted, into the ceiling.

13. Place the drop ceiling cover over the ceiling bracket and tighten the screws.

Safety wire

Ceiling tile

Ceiling bracket

Hook for

safety wire

Drop ceiling cover

Drop ceiling cover screws

Page 12 AXIS Q6034 Installation Guide

Bracket mount (optional accessory)

1. Install the selected bracket according to the

instructions supplied with the bracket. If drilling is

required, make sure to use drill bits, screws, and

plugs that are appropriate for the material.

2. Loosen the 3 camera base lid screws and remove

the camera base lid, see illustration on page 7.

3. Route the network cable and the multi-connector

cable, if applicable, through the holes in the

mounting bracket.

4. Hook the camera to the safety wire on the bracket.

5. Connect the network cable and, if applicable, the

multi-connector cable to the network camera.

6. Install AXIS T8123, see

Install the AXIS T8123 High PoE Midspan 1-port,

on page 13.

7. Put the camera base lid back in its original position.

8. Slide the unit holders on the network camera into the slots on the bracket and rotate the

camera unit.

9. Secure the network camera to the mounting bracket by fastening the 3 screws (Torx T30).

Wall bracket (mounting example)

Safety

wire

Slots for

Screws

Torx T30

unit holders

AXIS Q6034 Installation Guide Page 13

ENGLISH

Install the AXIS T8123 High PoE Midspan 1-port

AXIS T8123 High PoE Midspan 1-port enables Axis network video products with high power

consumption to receive data and power over the same Ethernet cable. Follow these instructions to

connect AXIS T8123.

1. Connect AXIS T8123 (Data in) to the network switch using a standard network cable.

2. Connect AXIS T8123 (Data and Power Out) to the network camera, using the network cable that

has been connected to the camera.

3. Connect AXIS T8123 to an AC outlet (100–240 V AC), using the supplied power cable.

For information on the LEDs on the midspan, see

AXIS T8123 Status indicators,

on page 23.

Data &

Power out Data in

Port

AC Input

connectivity

indicator

connectivity

indicator

Network camera Ethernet

AXIS T8123

Page 14 AXIS Q6034 Installation Guide

Assign an IP Address

Most networks today have a DHCP server that automatically assigns IP addresses to connected

devices. If your network does not have a DHCP server the network camera will use 192.168.0.90 as

the default IP address.

If you would like to assign a static IP address, the recommended method in Windows is either AXIS

IP Utility or AXIS Camera Management. Depending on the number of cameras you wish to install,

use the method that best suits your purpose.

Both of these free applications are available on the AXIS Network Video Product CD supplied with

this product, or they can be downloaded from www.axis.com

Notes:

• If assigning the IP address fails, check that there is no firewall blocking the operation.

• For other methods of assigning or discovering the IP address, e.g. in other operating systems, see

page 19.

Method Recommended for Operating system

AXIS IP Utility

See page 15

Single camera

Small installations

Windows

AXIS Camera Management

See page 16

Multiple cameras

Large installations

Installation on a different subnet

Windows 2000

Windows XP Pro

Windows 2003 Server

Windows Vista

AXIS Q6034 Installation Guide Page 15

ENGLISH

AXIS IP Utility - single camera/small installation

AXIS IP Utility automatically discovers and displays Axis devices on your network. The application

can also be used to manually assign a static IP address.

Note that the computer running AXIS IP Utility must be on the same network segment (physical

subnet) as the network camera.

Automatic discovery

1. Check that the network camera is connected to the network and that power has been applied.

2. Start AXIS IP Utility.

3. When the camera appears in the window, double-click it to open its home page.

4. See page 17 for instructions on how to assign the password.

Assign the IP address manually (optional)

1. Acquire an unused IP address on the same network segment as your computer.

2. Select the network camera in the list.

3. Click the Assign new IP address to the selected device button and enter the IP address.

4. Click Assign and follow the on-screen instructions. Note that the camera must be restarted

within 2 minutes for the new IP address to be set.

5. Click Home Page to access the camera’s web pages.

6. See page 17 for instructions on how to set the password.

Page 16 AXIS Q6034 Installation Guide

AXIS Camera Management - multiple cameras/large installations

AXIS Camera Management can automatically discover multiple Axis devices, show connection

status, manage firmware upgrades and set IP addresses.

Automatic discovery

1. Check that the camera is connected to the network and that power has been applied.

2. Start AXIS Camera Management. When the network camera appears in the window, right-click

the link and select Live View Home Page.

3. See page 17 for instructions on how to set the password.

Assign an IP address in a single device

1. Select the network camera in AXIS Camera Management and

click the Assign IP button.

2. Select Assign the following IP address and enter the IP

address, subnet mask and default router the device will use.

3. Click OK.

Assign IP addresses in multiple devices

AXIS Camera Management speeds up the process of assigning

IP addresses to multiple devices, by suggesting IP addresses

from a specified range.

1. Select the devices you wish to configure (different models

can be selected) and click the Assign IP button.

2. Select Assign the following IP address range and enter

the range of IP addresses, the subnet mask and default

router the devices will use.

3. Click Update. Suggested IP addresses are listed under New

IP Addresses and can be edited by selecting a device and

clicking Edit.

4. Click OK.

AXIS Q6034 Installation Guide Page 17

ENGLISH

Set the Password

To gain access to the product, the password for the default administrator user root must be set. This

is done in the ‘Configure Root Password’ dialog, which is displayed when the network camera is

accessed for the first time.

To prevent network eavesdropping when setting the root password, this can be done via an

encrypted HTTPS connection, which requires an HTTPS certificate.

Note: HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic between web

browsers and servers. The HTTPS certificate controls the encrypted exchange of information.

To set the password via a standard HTTP connection, enter it directly in the first dialog shown

below.

To set the password via an encrypted HTTPS connection, follow these steps:

1. Click the Create self-signed certificate button.

2. Provide the requested information and click OK. The certificate is created and the password can

now be set securely. All traffic to and from the network camera is encrypted from this point on.

3. Enter a password and then re-enter it to confirm the spelling. Click OK. The password has now

been configured.

4. To log in, enter the user name “root” in the dialog as requested.

Note: The default administrator user name root cannot be deleted.

5. Enter the password as set above, and click OK.

Note: If the password is lost, the camera must be reset to the factory default settings. See page 24.

To configure the password directly

via an unencrypted connection, enter

the password here.

To create an HTTPS connection,

start by clicking this button.

Page 18 AXIS Q6034 Installation Guide

Access the video stream

The Live View page of the network camera is displayed, with links to the Setup tools, which allow

you to customize the camera.

If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the video stream

in Internet Explorer. You will need administrator rights on the computer to do this.

If required, click the link to install missing decoders.

Note: To install AMC in Windows Vista, you must run Internet Explorer as an administrator. Right-click

the Internet Explorer icon and select Run as administrator.

Setup - Provides all the

tools for configuring the

camera to requirements.

Help - Displays

online help on all

aspects of using

the camera.

AXIS Q6034 Installation Guide Page 19

ENGLISH

Other Methods of Setting the IP address

The table below shows the other methods available for setting or discovering the IP address. All

methods are enabled by default, and all can be disabled.

Use in operating

system

Notes

AVHS Service

Connection

All To connect the camera to an AVHS server, refer to the server provider´s

Installation guide. For information and help to find a local AVHS

Service Provider go to www.axis.com

UPnP™

Windows When enabled on your computer, the camera is automatically detected

and added to “My Network Places.”

Bonjour

MAC OSX

(10.4 or later)

Applicable to browsers with support for Bonjour. Navigate to the

Bojour bookmark in your browser (e.g. Safari) and click on the link to

access the camera’s web pages.

AXIS Dynamic

DNS Service

All A free service from Axis that allows you to quickly and simply install

your camera. Requires an Internet connection with no HTTP proxy. See

www.axiscam.net for more information

ARP/Ping

All See below. The command must be issued within 2 minutes of

connecting power to the camera.

DHCP server

All To view the admin pages for the network DHCP server, see the server’s

own documentation.

Page 20 AXIS Q6034 Installation Guide

Set the IP address with ARP/Ping

1. Acquire an IP address on the same network segment your computer is connected to.

2. Locate the serial number (S/N) on the product label on the camera.

3. Open a command prompt on your computer and enter the following commands:

4. Check that the network cable is connected to the camera and then start/restart the camera, by

disconnecting and reconnecting power.

5. Close the command prompt when you see ‘Reply from 192.168.0.125: ...’ or similar.

6. In your browser, type in http://<IP address> in the Location/Address field and press Enter on

your keyboard.

Notes:

• To open a command prompt in Windows: from the Start menu, select Run... and type cmd. Click OK.

• To use the ARP command in WIndows Vista, right-click the command prompt icon and select Run as

administrator.

• To use the ARP command on a Mac OS X, use the Terminal utility in Application > Utilities.

Windows syntax: Windows example:

arp -s <IP Address> <Serial Number>

ping -l 408 -t <IP Address>

arp -s 192.168.0.125 00-40-8c-18-10-00

ping -l 408 -t 192.168.0.125

UNIX/Linux/Mac syntax: UNIX/Linux/Mac example:

arp -s <IP Address> <Serial Number> temp

ping -s 408 <IP Address>

arp -s 192.168.0.125 00:40:8c:18:10:00 temp

ping -s 408 192.168.0.125

Page is loading ...

Axis Q6034 Installation guide

This manual is also suitable for

Axis Q6034 Installation guide

in other languages

Related papers

Other documents