• NORTH AMERICA • 600 Mid Florida Drive Airport Industrial Park of Orlando, Florida 32824 • Tel. (407) 240-4000 Fax (407) 240-4046
• CARIBBEAN & SOUTH AMERICA • Urb. Aponte #5, San Lorenzo, Puerto Rico USA 00754 • Tel. (787) 736-4221 Fax (787) 736-5313
• CENTRAL AMERICA • Zona Industrial Bes, lote #4, El Coyol de Alajuela, Costa Rica • Tel. (506) 2438-2257 Fax (506) 2438-2162
Rev. 06 / 2016
Uses:
Chem Traffic™ is to be used on concrete floor surfaces, brick and other
paved surfaced. Regulatory colors established by U.S. Bureau of Public
Roads. Can be used on asphalt surfaces such as tennis courts, asphalt
driveways and parking lots.
Notice: The technical data contained herein are true and accurate to the best
of our knowledge. Published technical data and instructions are subject to
change without prior notice.
S.D.S.: Available upon request.
Surface Preparation:
All surfaces must be dry, clean, sound and free of contaminants such as dirt,
grease, chalk, mildew, oil, rust, concrete curing agents,laitance,
efflorescence, loose or badly cracked paint. No primer or under-coat is
necessary. Remove all contaminants by washing surfaces with an
appropriate cleaner, sanding, scrapping and/or using a pressure washing
machine. Do not paint on wet surfaces or when humidity is below 85%, nor
when temperature is below 50 ˚F (10 ˚C). When applied over emulsified coal
tar compound, the surface should be allowed to age seven days before
striping.
Method of Application:
Apply product with brush, roller or sprayer. Apply generously with a full
brush or roller and avoid excessive brushing or spreading too thinly.
Mixing and thinning: Mix always thoroughly before application. Thinning is
not recommended, if necessary use only 8oz. of mineral spirits per gallon of
this product.
Brush: Use a good quality nylon PA-1982 or polyester brush PA-1999.
Roller: Use a Lanco
®
All-Purpose 3/8” Nap Roller PA-566. Apply
generously, but avoid excessive brushing or reworking of painted areas, do
not apply or spread too thinly.
Spray: Spray equipment should be capable of maintaining a pressure of
700-1000 psi with a tip of 0.015 to 0.019.
Precaution: Do not add mineral spirits or other solvents to this product. Do
not apply when air or surface temperature is below 50 ˚F (10 ˚C). Apply
liberally,but do not overspread. Stop painting at least two hours before you
expect dew to form or the temperature to fall below 50 ˚F (10 ˚C).
Additional Information:
Clean up: Immediately after use, clean brushes, rollers or spray equipment
with warm water and detergent.
Caution: Harmful if swallowed. Contains acrylic resin. In case of eye contact,
flush thoroughly with water. Do not rub eyes. In case of skin contact, flush
area immediately with clean water. If swallowed, do not induce vomiting.
Consult a physician immediately. Use only with adequate ventilation.
Adequate ventilation required when sanding or abrading the dried film.
Always use (NIOSH/MSHA TC21C or equivalent.) Goggles are
recommended while handling the product.
Warning! If you scrape, sand, or remove old paint, you may release lead
dust. Lead is toxic. Exposure to lead dust can cause serious illness, such as
brain damage, especially in children. Pregnant women should also avoid
exposure. Wear a NIOSH-approved respirator to control lead exposure.
Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find
out how to protect yourself and your family by contacting the National Lead
Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
Keep out reach of children. For chemical emergency call ChemTrec
1-800-424-9300.
Chem Traffic™ CT-400 / CT-401
/
