Glidden PF8010-01 User manual

Brand: Glidden

Model: PF8010-01

Type: User manual

ASSURE D SAT I S FACTION L IMIT ED WA R R A N T Y

ICI Paints wa r rants satisfaction when applied according to label instru c t i o n s. If not satisfied, return the unused port i o n

along with the sales receipt to place of purchase.T h ey will refund the price paid for the product or replace with product

of equal va l u e.

THIS WARRANTY SPECIFICALLY EXCLUDES LABOR OR COST OF LABOR FOR THE APPLICATION OF ANY

PA I N T. Some states do not allow the exclusion of incidental or consequential damages, so the limitation or ex c l u s i o n

contained in the above wa r ranty may not apply to yo u . This wa r ranty gives you specific legal ri g h t s, and you may also

h ave other rights which va r y from state to state.

Call 1-800-545-2643 in the event

of an emergency, to order Material

Safety Data Sheets (MSDS) for

products, or questions concerning

product perfo rmance and

a p p l i c a t i o n . For full health and

safety information relative to the

proper use of this product, consult

The Glidden Material S a fety Data

Sheet (MSDS) for each product.

PRODUCT DESCRIPTION:

Glidden Porch & Floor Oil/Alkyd Polyurethane is designed to withstand foot

traffic and add decorative appeal in a durable gloss finish. Recommended for

use on interior or exterior wood and concrete floors. Ideal for stairs, porches,

railings, steps and boat decks. May also be used on other properly prepared

masonry, wood, and metal surfaces. Features excellent resistance to

abrasion, oils and washing. Not recommended for use on below grade

concrete floors laid directly on damp or water-bearing surfaces. Not

recommended for use on garage floors as the product may not adhere

satisfactorily to the tire lane areas.

FEATURES:

• Durable gloss finish

• Excellent abrasion and scuff resistance

• Excellent adhesion

• Oil resistant

• Easy application

• Excellent washability

• Interior or exterior use

• Performance alternate for Federal Paint Specification TT-E-487E

COMPOSITION:

• Polyurethane Resin

• Titanium Dioxide and Extender Pigments

• Not manufactured with lead or mercury containing materials.

PF80XX

Specifications:

C o l o r :

W h i t e ,r e a dy-mix

& custom colors

F i n i s h :

G l o s s ,70 units

minimum @ 60°

Clean-up Solvent:

Mineral spirits

D e n s i t y :

10.5 lbs/gal (1.26 kg/L)

Maximum VOC:

3.17 lbs/gal (380 g/L)

S o l i d s :

Vo l u m e : 52% +/- 1%

We i g h t : 70% +/- 1%

Practical

C ov e r a g e

Apply at 400-500 sq ft/gal

(10-12 m

/ L ) .Actual coverag e

may vary depending on

s u b s t r ate and ap p l i c at i o n

m e t h o d .

Flash

P o i n t

105°F (41°C)

D ry Time

77°F (25°C) & 50% RH:

To touch: 4-6 hours

To light traffic & recoat :

24 hours

P o rch & Floor Oil/Alkyd Polyurethane Gloss

C O L O R S

Porch Floor

Porch

Floor

C O L O R S

1 - 8 0 0 - G L I D D E N

w w w. g l i d d e n . c o m

Cleveland, Ohio 44115

DANGER!

COMBUSTIBLE LIQUID AND

VAPOR. HARMFUL OR FATAL IF

SWALLOWED. ASPIRATION

HAZARD - CAN ENTER LUNGS AND

CAUSE DAMAGE. HARMFUL IF

INHALED. MAY CAUSE CENTRAL

NERVOUS SYSTEM EFFECTS,

INCLUDING DIZZINESS, HEADACHE

OR NAUSEA. CAUSES EYE, SKIN

AND RESPIRATORY TRACT

IRRITATION. USE ONLY WITH

ADEQUATE VENTILATION. KEEP

OUT OF THE REACH OF CHILDREN.

NOTICE: Products in this series contain solvents.

Reports have associated repeated and prolonged

occupational overexposure to solvents with

permanent brain and nervous system damage.

Intentional misuse by deliberately concentrating and

inhaling the contents may be harmful or fatal.

For emergency information call (800) 545-2643.

Note: These warnings encompass the product

series. Prior to use, read and follow product-specific

MSDS and label information. Keep away from heat,

sparks and flame. Do not smoke. Vapors may ignite.

Extinguish all flames, burners, stoves, heaters and

pilot lights and disconnect all electrical motors and

appliances before use and until all vapors are gone.

Prevent build-up of vapors by opening all windows

and doors to achieve cross-ventilation. If sanding is

done, wear a dust mask to avoid breathing of

sanding dust. Do not breathe vapors or spray mist.

Ensure fresh air entry during application and drying.

If you experience eye watering, headaches, or

dizziness, leave the area. If properly used, a

respirator may offer additional protection. Obtain

professional advice before using. Close container

after each use. FIRSTAID: In case of skin contact,

wash thoroughly with soap and water. If any product

remains, gently rub petroleum jelly, vegetable or

mineral/baby oil onto skin, then wash again with

soap and water. Repeated applications may be

needed. Remove contaminated clothing. For eye

contact, flush immediately with large amounts of

water, for at least 15 minutes. Obtain emergency

medical treatment. If swallowed, obtain medical

treatment immediately. If inhalation causes physical

discomfort, remove to fresh air. If discomfort persists

or any breathing difficulty occurs, get medical help.

KEEP FROM FREEZING. DS37-1100

SHIPPING: Freight Classification: Paint,

Combustible Liquid, PGIII

PACKAGING: 1 gallon (3.785 L)

FLASH POINT: 105°F (41°C)

GENERAL SURFACE PREPA R AT I O N :

All surfaces must be sound, dry, clean and free of oil, grease, dirt, mildew, form

release agents, curing compounds, loose and flaking paint and other foreign

substances.

NEW SURFAC E S :

Concrete (concrete floors) and Masonry - Do not use on floors subject to

dampness from the ground. Cure at least 30 days before painting. Roughen slick

poured or precast concrete and remove sealers by chemical cleaning or abrasive

method such as sandsweeping. Rinse thoroughly with water and allow to dry.

Must be internally dry. Remove loose aggregate. Prime with this product. Fill

block with latex filler. Wood - Prime with this product. Steel - Prime with

solventborne metal primer. Galvanized Metal and Aluminum - Prime with

solventborne galvanized metal.

P R E V I O U S LY PAINTED SURFAC E S :

Wash to remove contaminants. Rinse thoroughly with water and allow to dry. Dull

glossy areas by light sanding. Remove sanding dust. Remove loose paint. Scrub

heavy chalk areas and overhead (exterior) areas such as eaves with soap and

water. Remove all mildew by washing with a solution of 16 oz (473 mL) liquid

household bleach and two oz (59 mL) non-ammoniated liquid detergent per

gallon (3.785 L) of water. Rinse thoroughly with water and allow to dry. Prime

bare areas with primer specified under NEW SURFACES.

Removal of old paint by sanding, scraping or other means may generate dust or

fumes that contain lead. Exposure to lead dust or fumes may cause adverse

health effects, especially in children or pregnant women. Controlling exposure to

lead or other hazardous substances requires the use of proper protective

equipment, such as properly fitted respirator (NIOSH approved) and proper

containment and cleanup. For additional information, contact the USEPA/Lead

Information Hotline at 1-800-424-LEAD.

T I N T I N G :

Tint the appropriate base with universal colorants.

SPREADING RAT E :

Apply at 400-500 sq ft/gal (10-12 m

/L). Actual coverage may vary depending on

substrate and application method.

A P P L I C AT I O N :

Mix thoroughly before use. May be applied by brush, roller or spray. Do not thin.

For airless spray use a .015" tip. Adjust pressure as needed. Do not apply when

surface or air temperature is below 40°F (4°C) or if rain or heavy dew is

expected within 12 hours of application. Two coats are suggested for best

results. For interior use, allow adequate ventilation during application and drying.

CAUTION: Surfaces coated with this product may become slippery when wet.

For additional slip resistance in areas of pedestrian traffic, add one pound per

gallon of coarse pumice or other texturing material.

D RYING T I M E :

At 77°F (25°C) and 50% R.H., dries to touch in four to six hours, to light foot

traffic and recoat in 24 hours. Low temperature, high humidity, thick films or poor

ventilation will increase these times.

C L E A N - U P :

Clean immediately with mineral spirits.

PF80XX, 9/02

Surface Preparation

Glidden PF8010-01 User manual

Brand: Glidden

Model: PF8010-01

Type: User manual

Download PDF

report

Glidden PF8010-01 User manual

Glidden PF8010-01 User manual

Related papers

Other documents