PERLESMITH PSLFK3-24 Installation guide

Brand: PERLESMITH

Model: PSLFK3-24

Category: Flat panel wall mounts

Type: Installation guide

PSLFK3-24

V1.0

LARGE FULL-MOTION TV WALL MOUNT

Thank you for choosing our product! We strive to provide the best quality and

services for our customers. Would you kindly share your experience on Amazon if

\RXDUHVDWLVƉHG"6KRXOG\RXKDYHDQ\LVVXHVSOHDVHGRQWKHVLWDWHWRFRQWDFWXV

7HOHSKRQHғ0RQ)ULDPSP36786$

(PDLOғVXSSRUWXV#SHUOHVPLWKFRP86&$'(8.)5,7(6-3$8

English ------------------------ 1-10

Deutsch ------------------------ 11-20

Français------------------------ 21-30

Español ------------------------ 31-40

Italiano ------------------------ 41-50

Tools Needed

Hammer

Getting Started

WARNING:

Exceeding the weight capacity can result in serious personal injury or damage to

equipment! It is the installer’s responsibility to make sure the weight of the TV (with

accessories) does not exceed 60 kg.

WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER

INSTALLATION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.

If you do not understand the instructions or have any concerns or questions, please contact a

qualified installer.

Do not install or assemble if the product or hardware is damaged or missing. Not all parts and

hardware included must be used. If you require replacement parts, contact customer service at

VXSSRUWXV#SHUOHVPLWKFRP

This product has been designed for use on a vertical wall constructed of wood studs. Wood studs

being defined as a wall consisting of a minimum of 2” x 4” studs with a maximum of 16” stud

spacing with a maximum of 1/2” of wall covering (drywall, lath, plaster).For custom installations

please contact a qualified installer. For safe installation, the wall you are mounting to must support

4 times the weight of the total load. If not, the surface must be reinforced to meet this standard.

The installer is responsible for verifying that the wall structure/surface will safely support the total

load.

This product may contain moving parts. Use with caution.

DO NOT EXCEED THE MAXIMUM WEIGHT CAPACITY FOR THIS PRODUCT.

Please check www.perlesmith.com for more products and company information.

Stud

Finder

Tape

measure

1/2 in.

(12.7 mm)

7/32 in.

(5.5 mm)

Wood Drill

Screw

driver

Pencil Level

(included

inside the box)

Drill

3/8 in.

(10 mm)

Concrete Drill

CAUTION!

60 kg

MAXIMUM WEIGHT CAPACITY

Arm and

Wall Plate

TV Brackets

Arm Extensions

Hardware Included

Front Support

End Caps

04 x2

Hardware Wall /Product)

5/16 x 2½ in

Lag Bolts

Wall

Anchor

Washers

Ø8mm

Allen Wrench

This product contains

small items that could be a choking hazard if

swallowed. Before starting assembly, verify

all parts are included and undamaged. If

any parts are missing or damaged, do not

return the damaged item to your dealer;

please contact our customer service team.

Never use damaged parts!

NOTE: Not all parts and hardware included

will be used.

WARNING:

Philips Screws

M6 x 15mm

M6 x 30mm

Philips

Screws

M6 x 50mm

Washers

Ø6mm

M4-5-6

Spacers

L10mm

x4x4

Philips Screws

M8 x 15mm

M8 x 45mm

x4 x8 x4

M-DM-A M-B

M-C

M-E

Philips

Screws

M8 x 65mm

M-F M-G

M-H

Spacers

L5mm

M-I

TV Screws / Washers

Hardware

Nuts

Washers

Ø8mm

product)

Wall Extension A

Wall Extension B

STEP 1-1 Select TV

Screw Diameter

STEP 1-2 Select TV

Screw Length

Thread screws by hand into the threaded holes on the back of your TV to select which screw

diameter fits your TV.

Correct

Too Long

Too Short

Measurement

200mm~600mm

7.9”~23.6”

100mm~400mm

3.9”~15.7”

STEP 1-3

Attach the TV Bracket

(a) Flat Back

Position your TV brackets over your TV hole pattern - making sure the brackets are centered

and level over the TV hole pattern.

Secure the brackets using your screw/washer/spacer selection:

(a) for Flat Back

(b) for Round Back / Extra space

CAUTION: Ensure TV bracket is securely fastened before moving on to the next step.

(b) Round Back /

Extra Space

M-A M-D

M-H

M-B

M-C

M-E

M-F

M-H

M-G M-I

STEP 2A

Wall Plate Installation (Wood stud)

2A-1

Attach the Extensions to the wall plate

the wall plate extensions can be moved

0.6”(15mm) for both side if necessary.

only one side need to attach each of

extensions A and B

For 18”(457mm) to 24”(610mm) space studs

For studs with the sapce between

16.5“(420mm) to 18”(457mm)

0.6 Zoll

CAUTION:

Avoid potential personal injury

or property damage! All lag bolts

MUST BE

firmly tightened to prevent unwanted movement

of the wall plate

CAUTION: Ensure the wall plate is securely fastened to the wall before continuing

on to the next step.

ƕ Drywall covering the wall must not exceed 5/8 in. (16 mm)

ƕ Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)

2A-2

Locate your studs. Verify and

mark the center of the studs by

finding the stud edges using an

awl, a thin nail, or an

edge-to-edge stud finder.

16”~24”

(406mm ~ 610mm)

2A-3

Drill 4 pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.

Make sure the depth is not less than 2 3/4” (70mm).

7/32 in.

Ø5.5 mm

in. (70 mm)

Configure A For 24”(610mm)

space studs

Configure B For 18” (457mm)

space studs

Configure C For 16.5” (420mm)

to 18”(457mm) space studs

Mount wall plate using 4 sets of 5/16 lag bolts (a) and washers B with a

1/2 in. socket wrench (not included).

2A-4

2A-2

Use wall plate to mark

mounting location x4 locations

for 24”(420mm)space

studs

Mark the 4 inside holes for

18”(457mm)space studs

Holes pattern for

16.5”(420mm) to 18”

(457mm) space studs. Only

one sied need to install the Wall

Extension

OPT A OPT B OPT C

left

right

left

right

STEP 2B

Wall Plate Installation (Concrete or brick, No need wall extensions 06A and 06B )

CAUTION:

Avoid potential personal injury

or property damage! All lag bolts

MUST BE

firmly tightened to prevent unwanted movement

of the wall plate

CAUTION: Ensure the wall plate is securely fastened to the wall before continuing

on to the next step.

Drill pilot

holes

2B-2

2B-3

Concrete Wall

Install wall plate using lag bolts

and washer and anchor .

Tighten the lag bolts until they are

pulled firmly against the wall plate

2.75in 70 mm

Ø 10 mm

2B-1

Position the

wall plate

at your

desired

height , level

the wall plate

and mark the

pilot hole

locations.

STEP 3

Install Front support and extensions and End cap together.

Install the extensions [03] to Front support [02] with the pre-assembled screws.

Install the extensions [03] to Front support [02] withe the pre-assembled screws.

3-1

3-2

Pre-assembled scews

Finished

3-3

STEP 4

Hang TV with brackets [04] onto the arm extensions [02] and [03].

Hang 02 onto 01 and using a screwdriver, secure with preassembled screws

Remove the

preassembled

screws [S2] and

save to use, then

raise the safety

locks.

Press the safety locks

then fasten the removed

screws [S2].

P10

[S1]

TO ADJUST TV LEVEL, loosen the two screws [S1] on the

rear of the arm plate, adjust level, and retighten to secure.

To adjust the tilt in both sides, loosen both tilt nuts and move panel to

desired position. Tighten both tilt nuts to hold desired tilt.

TIGHTEN

LOOSEN

TIGHTEN

± 3°

PERLESMITH PSLFK3-24 Installation guide

Brand: PERLESMITH

Model: PSLFK3-24

Category: Flat panel wall mounts

Type: Installation guide

Download PDF

report

PERLESMITH PSLFK3-24 Installation guide

PERLESMITH PSLFK3-24 Installation guide

Related papers

Other documents