Toro Electrical Service Module, Mid-Size Mowers Installation guide

Toro
Brand
Toro
Model
Electrical Service Module, Mid-Size Mowers
Category
Car kits
Type
Installation guide

Toro Electrical Service Module, Mid-Size Mowers, offers a convenient and efficient way to enhance the functionality of your Toro T-Bar mid-size mower. This module enables you to effortlessly connect and control various electrical accessories, providing increased versatility and ease of use. Designed for quick and simple installation, the module seamlessly integrates with your mower's existing wiring system. With the Toro Electrical Service Module, you can expand the capabilities of your mower and tackle a wider range of tasks with greater efficiency and precision.

Toro Electrical Service Module, Mid-Size Mowers, offers a convenient and efficient way to enhance the functionality of your Toro T-Bar mid-size mower. This module enables you to effortlessly connect and control various electrical accessories, providing increased versatility and ease of use. Designed for quick and simple installation, the module seamlessly integrates with your mower's existing wiring system. With the Toro Electrical Service Module, you can expand the capabilities of your mower and tackle a wider range of tasks with greater efficiency and precision.

2004 by The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
Contact us at www.Toro.com
All Rights Reserved
Printed in the USA
Original Instructions (EN)
Electric Service Module Kit
for T-Bar Mid–Size Mowers
Part No. 107-4113
Form No. 3351–544
Installation Instructions
This kit can be installed on all T–Bar machines.
Loose Parts
Note: Use the chart below to identify parts for assembly.
Description Qty. Use
Electric module assembly 1 Installing the electric service module
Removing the Existing Module
1. Stop the machine, engage the parking brake, turn the
engine off and remove the key.
2. Disconnect the negative battery cable from the battery if
installing on an electric start unit.
3. Remove the screws securing the control panel cover to
the underside of the control panel (Fig. 1).
m–7631
1
2
3
Figure 1
1. Screw
2. Control panel cover
3. Control panel
4. Locate the relay shown in the Figure 2. Remove the
fasteners securing the relay to the control panel cover.
Save the fasteners for later use.
m-7632
2
3
5
4
1
Figure 2
1. Control panel cover
2. Relay module
3. Fastener
4. Flat, square connector
5. Bullet connector, brown
5. Remove the relay module from the wiring harness by
disconnecting male end of the flat, square connector and
the brown wire bullet plug from the wiring harness
(Fig. 2).
2
6. Cut the wires connecting the female end of the flat,
square connecter at the base of the connector (Fig. 3).
Important Pull out on the connector ensure the wires
are cut close to connector. This allows enough wire for the
insulation to be cut back and the new connector installed.
m–7633
1
3
Figure 3
1. Flat connector
2. Pull out on connector
3. Cut here
Installing the Electric Service
Module
1. Use a electrician’s tool to strip 1/4 inch of the insulation
on the wires from the cut ends (Fig. 4).
2. Connect the crimping connections on the wires from the
end of the male connector of the electric service module
to the cut wires from the electrical harness (Fig. 4).
3. Match the wires color for color and crimp the clear
connectors to secure the module to the wiring harness
(Fig. 4).
3
1
4
2
m–7634
Figure 4
1. Male connector, new
module
2. Cut wires from existing
harness
3. Crimping connectors
4. Exposed wire, cut back
insulation 1/4 inch
4. Connect the female end of the electric service module to
the male connector installed previously (Fig. 5).
5. Connect the male end of the bullet connector from the
brown wire to the female end of the bullet connector
from the existing wiring harness (Fig. 5).
m–7635
3
1
2
4
Figure 5
1. Female end connector,
electric service module
2. Male end connector,
electric service module
3. Male end, bullet
connector
4. Female end, bullet
connector
6. Secure the new relay to the control panel cover using
the fasteners removed previously (Fig. 6).
m–7636
2
3
5
4
1
Figure 6
1. Control panel cover
2. Relay
3. Fasteners, removed
previously
4. Electric service module
connector
5. Bullet connector, brown
7. Install the cover plate to the control panel using the
fasteners removed previously (Fig. 6).
8. Connect the negative battery cable.
  • Page 1 1
  • Page 2 2

Toro Electrical Service Module, Mid-Size Mowers Installation guide

Toro
Brand
Toro
Model
Electrical Service Module, Mid-Size Mowers
Category
Car kits
Type
Installation guide

Toro Electrical Service Module, Mid-Size Mowers, offers a convenient and efficient way to enhance the functionality of your Toro T-Bar mid-size mower. This module enables you to effortlessly connect and control various electrical accessories, providing increased versatility and ease of use. Designed for quick and simple installation, the module seamlessly integrates with your mower's existing wiring system. With the Toro Electrical Service Module, you can expand the capabilities of your mower and tackle a wider range of tasks with greater efficiency and precision.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents