2. Computers & electronics
  3. Telecom & navigation
  4. Mobile phones
  5. Car kits
  6. Dodge
  7. Timing
Timing

Dodge Timing Installation guide

  • Hello! I've reviewed the user manual for the Timing Chain RAM 1500 Truck 2WD V8-5.7L, which includes detailed instructions for installation, proper timing mark alignment, and cautions to prevent engine damage. I'm ready to answer your questions regarding the timing chain installation process.
  • What special tool is required for this installation?
    What is the main caution to observe during this timing chain installation?
    What should be done if the camshaft needs to be rotated more than a few degrees?
6/8/2021
Timing Chain & Sprockets - Installation (Timing Chain) - ALLDATA Repair
https://my.alldata.com/repair/#/repair/article/53527/component/57/itype/401/nonstandard/211881/selfRefLink/true
1/5
2014 Dodge or Ram Truck RAM 1500 Truck 2WD V8-5.7L
Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Chain > Service and Repair >
Removal and Replacement
TIMING CHAIN & SPROCKETS - INSTALLATION
INSTALLATION
Special Tools
8514A - Pins, Tensioner
Originally Shipped In Kit Number(s)
.
8283, 8283CC, 8527, 8527CC, 8575,
8575CC, 9975
CAUTION:This is a Zero-Tolerance engine. Failure to properly align the to the timing gears will
cause severe engine damage. It is imperative that the Timing Marks shown in the subsequent steps
be properly aligned during assembly.
timing chain
1.
Install the (1) and position halfway
onto the crankshaft.
CAUTION:Do not rotate the more than a few
degrees independently of the .
Valve to contact could occur resulting in
possible valve damage. If the camshaft need
to be rotated more than a few degrees, first
move the pistons away from the s
by rotating the crankshaft counterclockwise to
a position 30°before-top-dead-center. Once
the camshaft is returned to their top-dead-
center position, rotate the crankshaft
clockwise to return the crankshaft to top-dead-
center.
camshaft
crankshaft
piston
cylinder head
crankshaft sprocket
2. While holding the camshaft phaser in hand, position the timing chain on the camshaft phaser and align the
timing marks as shown.
6/8/2021
Timing Chain & Sprockets - Installation (Timing Chain) - ALLDATA Repair
https://my.alldata.com/repair/#/repair/article/53527/component/57/itype/401/nonstandard/211881/selfRefLink/true
2/5
3. While holding the camshaft phaser and timing chain in
hand, position the timing chain on the crankshaft
sprocket and align the timing mark as shown.
4. Align the slot in the camshaft phaser with the dowel on the camshaft and position the camshaft phaser on
the camshaft while sliding the crankshaft sprocket into position.
5. Install the camshaft phaser bolt (1) and tighten
tight.
finger
6. If removed, install the (1). Tighten bolts (2) to the proper . timing chain guide (Torque Specifications)
6/8/2021
Timing Chain & Sprockets - Installation (Timing Chain) - ALLDATA Repair
https://my.alldata.com/repair/#/repair/article/53527/component/57/itype/401/nonstandard/211881/selfRefLink/true
3/5
7. If removed, install the (2) and
tighten the bolts (3) to the proper
.
timing chain tensioner
(Torque Specifications)
8. Remove the tensioner pin (1). 8514A
6/8/2021
Timing Chain & Sprockets - Installation (Timing Chain) - ALLDATA Repair
https://my.alldata.com/repair/#/repair/article/53527/component/57/itype/401/nonstandard/211881/selfRefLink/true
4/5
9. The timing mark located on the camshaft phaser must be properly centered between the dual marks on the
timing chain while at the 12 O'clock position (1). The timing mark located on the crankshaft must be properly
aligned with the single mark on the timing chain while at the 6 O'clock position (2).
10. Verify that the chains are operating smoothly. The chain must be replaced if:
Any kinks
Signs of binding
Damage to the links
Signs of wear or stretching.
11. Tighten the camshaft phaser bolt (1) to the proper
. (Torque Specifications)
12. Install the .oil pump (Refer to 09 - Engine/Lubrication/PICK-UP, Oil Pump/Installation)
6/8/2021
Timing Chain & Sprockets - Installation (Timing Chain) - ALLDATA Repair
https://my.alldata.com/repair/#/repair/article/53527/component/57/itype/401/nonstandard/211881/selfRefLink/true
5/5
13. Fill the engine with oil
.
(Refer to 04 - Vehicle Quick Reference/Capacities and Recommended
Fluids/Specifications)
14. Fill the .cooling system (Refer to 07 - Cooling - Standard Procedure)
15. Connect the negative battery cable.
16. Start the engine and check for leaks.
/