Honda 2014 Accord Sedan L4-2.4L K24W1 Operating instructions

Brand: Honda

Model: 2014 Accord Sedan L4-2.4L K24W1

Type: Operating instructions

This manual is also suitable for

2014 Honda Accord Sedan

8/12/22, 7:58 AM

Engine Oil Pan Removal and Installation (L4) (Oil Pan) - ALLDATA Repair

https://my.alldata.com/repair/#/repair/article/53574/component/71/itype/401/nonstandard/102172/selfRefLink/true

1/11

2014 Honda Accord Sedan L4-2.4L (K24W1)

Vehicle > Engine, Cooling and Exhaust > Engine > Engine Lubrication > Oil Pan > Service and Repair > Removal and

Replacement

ENGINE OIL PAN REMOVAL AND INSTALLATION (L4)

Removal and InstallationEngine Oil Pan

Removal

1. Steering Joint - Disconnect

.Disconnect the steering joint (CLICK HERE)

NOTE: Hold the steering wheel in the steering

wheel holder tool.

2. A/C Compressor - Remove

Remove the A/C compressor without

disconnecting the A/C hoses. Do not bend the

A/C hoses excessively.

NOTE: Hang the A/C compressor with a wire tie.

3. Front Mounting Bolt - RemoveEngine Mount

8/12/22, 7:58 AM

Engine Oil Pan Removal and Installation (L4) (Oil Pan) - ALLDATA Repair

https://my.alldata.com/repair/#/repair/article/53574/component/71/itype/401/nonstandard/102172/selfRefLink/true

2/11

1. Disconnect the vacuum hose (A).

2. Remove the front engine mount stop (B) and

the front engine mount mounting bolt (C).

4. Engine Undercover - Remove

.Remove the engine undercover (CLICK HERE)

5. Engine Oil - Drain

.Drain the engine oil (CLICK HERE)

6. A or Under-Floor /Exhaust Pipe A - RemoveExhaust Pipe TWC

Remove exhaust pipe A or under-floor

TWC/exhaust pipe A:

•Exhaust Pipe A (CLICK HERE)

•Under-Floor TWC/Exhaust Pipe A (CLICK

HERE)

7. Clutch Case - RemoveCover

8/12/22, 7:58 AM

Engine Oil Pan Removal and Installation (L4) (Oil Pan) - ALLDATA Repair

https://my.alldata.com/repair/#/repair/article/53574/component/71/itype/401/nonstandard/102172/selfRefLink/true

3/11

Remove the clutch case cover (A) and the

transmission mounting bolts (B).

8. Transmission - Support

Support the transmission with a transmission

jack and a wood block under the transmission.

9. Lower Transmission Mount Mounting Bolt - Remove

Remove the lower transmission mount

mounting bolts (A).

NOTE: Do not remove the bolt (B) from the lower

transmission mount. If the bolt is removed, the

lower transmission mount must be replaced as

an assembly.

10.Transmission Jack - Remove

Remove the transmission jack and the wood

block.

11.Front Subframe - Support

Lift and support under the front of the front

subframe with a transmission jack.

8/12/22, 7:58 AM

Engine Oil Pan Removal and Installation (L4) (Oil Pan) - ALLDATA Repair

https://my.alldata.com/repair/#/repair/article/53574/component/71/itype/401/nonstandard/102172/selfRefLink/true

4/11

12.Front Subframe Middle Mount Rubber Mounting Bolt - Loosen

Loosen the front subframe middle mount rubber

mounting bolts (A) on both sides.

13.Front Subframe - Move

Rear side 1. Loosen the mounting bolts (A) from the front

subframe (B) on rear side, so they are about

10 mm (0.39 in) from the mounting surface.

8/12/22, 7:58 AM

Engine Oil Pan Removal and Installation (L4) (Oil Pan) - ALLDATA Repair

https://my.alldata.com/repair/#/repair/article/53574/component/71/itype/401/nonstandard/102172/selfRefLink/true

5/11

Front side 2. Remove the mounting bolts (A) from the front

subframe (B) on front side.

3. Lower the jack slowly until the front subframe

has dropped about 90 mm (3.54 in).

14. - RemoveOil Pan

1. Using a flat blade screwdriver, separate the oil

pan from the lower block in the places shown.

8/12/22, 7:58 AM

Engine Oil Pan Removal and Installation (L4) (Oil Pan) - ALLDATA Repair

https://my.alldata.com/repair/#/repair/article/53574/component/71/itype/401/nonstandard/102172/selfRefLink/true

6/11

2. Remove the oil pan.

Installation

1. Oil Pan - Install

1. Remove all of the old liquid gasket from the

oil pan mating surfaces, the bolts, and the

bolt holes.

2. Clean and dry the oil pan mating surfaces.

3. Apply liquid gasket, (P/N 08718-0003, 08718-

0004 or 08718-0009) to the

mating surface of the oil pan, and to the

inside edge of the threaded bolt holes. Install

the component within 5 minutes of applying

the liquid gasket.

engine block

NOTE:

•Apply a 2.5 mm (0.098 in) diameter bead of

liquid gasket along the broken line (A).

•If too much time has passed after applying

the liquid gasket, remove the old liquid

gasket and residue, then reapply new liquid

gasket.

8/12/22, 7:58 AM

Engine Oil Pan Removal and Installation (L4) (Oil Pan) - ALLDATA Repair

https://my.alldata.com/repair/#/repair/article/53574/component/71/itype/401/nonstandard/102172/selfRefLink/true

7/11

4. Install the oil pan (A) with a new O-ring (B).

5. Tighten the bolts in three steps. In the final

step, torque all bolts, in sequence, to 12 N·m

(1.2 kgf·m, 9 lbf·ft). Wipe off the excess liquid

gasket on the each side of

and flywheel/drive plate.

crankshaft pulley

NOTE:

•Wait at least 30 minutes before filling the

engine with oil.

•Do not run the engine within 3 hours after

installing the oil pan.

2. Front Subframe - Align

.Align the front subframe (CLICK HERE)

8/12/22, 7:58 AM

Engine Oil Pan Removal and Installation (L4) (Oil Pan) - ALLDATA Repair

https://my.alldata.com/repair/#/repair/article/53574/component/71/itype/401/nonstandard/102172/selfRefLink/true

8/11

3. Transmission Jack - Remove

Remove the transmission jack from the front

subframe.

4. Front Subframe Middle Mount Rubber Mounting Bolt - Tighten

Tighten the front subframe middle mount rubber

mounting bolts (A) to the specified torque on

both sides.

5. Lower Transmission Mount Mounting Bolt - Install

Install the new lower transmission mount

mounting bolts.

6. Clutch Case Cover - Install

8/12/22, 7:58 AM

Engine Oil Pan Removal and Installation (L4) (Oil Pan) - ALLDATA Repair

https://my.alldata.com/repair/#/repair/article/53574/component/71/itype/401/nonstandard/102172/selfRefLink/true

9/11

Install the clutch case cover (A) and the

transmission mounting bolts (B).

7. Exhaust Pipe A or Under-Floor TWC/Exhaust Pipe A - Install

Install exhaust pipe A or under-floor

TWC/exhaust pipe A:

•Exhaust Pipe A (CLICK HERE)

•Under-Floor TWC/Exhaust Pipe A (CLICK

HERE)

8. Engine Undercover - Install

.Install the engine undercover (CLICK HERE)

9. Front Engine Mount Mounting Bolt - Tighten

8/12/22, 7:58 AM

Engine Oil Pan Removal and Installation (L4) (Oil Pan) - ALLDATA Repair

https://my.alldata.com/repair/#/repair/article/53574/component/71/itype/401/nonstandard/102172/selfRefLink/true

10/11

1. Tighten the new front engine mount mounting

bolt (A).

2. Install the front engine mount stop (B) using

new nuts (C).

3. Connect the vacuum hose (D).

10.A/C Compressor - Install

Install the A/C compressor.

11.Engine Oil - Refill

.Refill the engine with engine oil (CLICK HERE)

12.Steering Joint - Connect

.Connect the steering joint (CLICK HERE)

8/12/22, 7:58 AM

Engine Oil Pan Removal and Installation (L4) (Oil Pan) - ALLDATA Repair

https://my.alldata.com/repair/#/repair/article/53574/component/71/itype/401/nonstandard/102172/selfRefLink/true

11/11

13.Wheel Alignment - Check

.Check the wheel alignment (CLICK HERE)

14.VSA Sensor Neutral Position - Memorize

Do the VSA sensor neutral position

memorization (CLICK HERE)

15.Steering Angle Sensor Neutral Position - Clear

Do the steering angle sensor neutral position

clear (CLICK HERE)

16.TPMS - Calibration

.Do the TPMS calibration (CLICK HERE)

Honda 2014 Accord Sedan L4-2.4L K24W1 Operating instructions

Brand: Honda

Model: 2014 Accord Sedan L4-2.4L K24W1

Type: Operating instructions

This manual is also suitable for

2014 Honda Accord Sedan

Download PDF

report

Honda 2014 Accord Sedan L4-2.4L K24W1 Operating instructions

This manual is also suitable for

Honda 2014 Accord Sedan L4-2.4L K24W1 Operating instructions

Related papers

Other documents