Extron electronic MGP 462D User manual

MGP 462D

Multi-Graphic Processor

68-840-01 Rev. C

08 06

MGP 462

Precautions

This symbol is intended to alert the user of important operating and maintenance

(servicing) instructions in the literature provided with the equipment.

This symbol is intended to alert the user of the presence of uninsulated dangerous

voltage within the product's enclosure that may present a risk of electric shock.

Caution

Read Instructions • Read and understand all safety and operating instructions before using the

equipment.

Retain Instructions • The safety instructions should be kept for future reference.

Follow Warnings • Follow all warnings and instructions marked on the equipment or in the user

information.

Avoid Attachments • Do not use tools or attachments that are not recommended by the equipment

manufacturer because they may be hazardous.

Warning

Power sources • This equipment should be operated only from the power source indicated on the product.

This equipment is intended to be used with a main power system with a grounded (neutral)

conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or disable it.

Power disconnection • To remove power from the equipment safely, remove all power cords from the rear

of the equipment, or the desktop power module (if detachable), or from the power source receptacle

(wall plug).

Power cord protection • Power cords should be routed so that they are not likely to be stepped on or

pinched by items placed upon or against them.

Servicing • Refer all servicing to qualified service personnel. There are no user-serviceable parts inside. To

prevent the risk of shock, do not attempt to service this equipment yourself because opening or

removing covers may expose you to dangerous voltage or other hazards.

Slots and openings • If the equipment has slots or holes in the enclosure, these are provided to prevent

overheating of sensitive components inside. These openings must never be blocked by other objects.

Lithium battery • There is a danger of explosion if battery is incorrectly replaced. Replace it only with the

same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the

manufacturer's instructions.

Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le matériel

contient des instructions importantes concernant l’exploitation et la maintenance

(réparation).

Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier de l’appareil de

tensions dangereuses non isolées posant des risques d’électrocution.

Attention

Lire les instructions• Prendre connaissance de toutes les consignes de sécurité et d’exploitation avant

d’utiliser le matériel.

Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir les consulter à l’avenir.

Respecter les avertissements • Observer tous les avertissements et consignes marqués sur le matériel ou

présentés dans la documentation utilisateur.

Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils non recommandés par le

fabricant du matériel car cela risquerait de poser certains dangers.

Avertissement

Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation indiquée sur l’appareil.

Ce matériel doit être utilisé avec une alimentation principale comportant un fil de terre (neutre). Le

troisième contact (de mise à la terre) constitue un dispositif de sécurité : n’essayez pas de la

contourner ni de la désactiver.

Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger, déconnectez tous les

cordons d’alimentation de l’arrière de l’appareil ou du module d’alimentation de bureau (s’il est

amovible) ou encore de la prise secteur.

Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de manière à ce que

personne ne risque de marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés par des objets.

Réparation-maintenance • Faire exécuter toutes les interventions de réparation-maintenance par un

technicien qualifié. Aucun des éléments internes ne peut être réparé par l’utilisateur. Afin d’éviter tout

danger d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces opérations car

l’ouverture ou le retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.

Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci servent à

empêcher les composants internes sensibles de surchauffer. Ces ouvertures ne doivent jamais être

bloquées par des objets.

Lithium Batterie • Il a danger d'explosion s'll y a remplacment incorrect de la batterie. Remplacer

uniquement avec une batterie du meme type ou d'un ype equivalent recommande par le constructeur.

Mettre au reut les batteries usagees conformement aux instructions du fabricant.

Safety Instructions • English

Consignes de Sécurité • Français

Sicherheitsanleitungen • Deutsch

Dieses Symbol soll dem Benutzer in der im Lieferumfang enthaltenen

Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung

(Instandhaltung) geben.

Dieses Symbol soll den Benutzer darauf aufmerksam machen, daß im Inneren des

Gehäuses dieses Produktes gefährliche Spannungen, die nicht isoliert sind und

die einen elektrischen Schock verursachen können, herrschen.

Achtung

Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden, sollten Sie alle Sicherheits-

und Bedienungsanleitungen genau durchlesen und verstehen.

Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie

aufbewahren, damit Sie im Bedarfsfall darauf zurückgreifen können.

Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und Anleitungen auf dem Gerät oder in

der Benutzerdokumentation.

Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte, die nicht ausdrücklich vom

Hersteller empfohlen wurden, da diese eine Gefahrenquelle darstellen können.

Vorsicht

Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene Stromquelle betrieben

werden. Dieses Gerät wurde für eine Verwendung mit einer Hauptstromleitung mit einem geerdeten

(neutralen) Leiter konzipiert. Der dritte Kontakt ist für einen Erdanschluß, und stellt eine

Sicherheitsfunktion dar. Diese sollte nicht umgangen oder außer Betrieb gesetzt werden.

Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten Sie alle Netzkabel

aus der Rückseite des Gerätes, aus der externen Stomversorgung (falls dies möglich ist) oder aus der

Wandsteckdose ziehen.

Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im Weg liegen und

niemand darauf treten kann oder Objekte darauf- oder unmittelbar dagegengestellt werden können.

Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal durchgeführt

werden. Die internen Komponenten des Gerätes sind wartungsfrei. Zur Vermeidung eines

elektrischen Schocks versuchen Sie in keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der

Abdeckungen die Gefahr eines elektrischen Schlags und/oder andere Gefahren bestehen.

Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist, dienen diese zur

Vermeidung einer Überhitzung der empfindlichen Teile im Inneren. Diese Öffnungen dürfen niemals

von anderen Objekten blockiert werden.

Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird. Ersetzen Sie verbrauchte

Batterien nur durch den gleichen oder einen vergleichbaren Batterietyp, der auch vom Hersteller

empfohlen wird. Entsorgen Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.

Este símbolo se utiliza para advertir al usuario sobre instrucciones importantes de

operación y mantenimiento (o cambio de partes) que se desean destacar en el

contenido de la documentación suministrada con los equipos.

Este símbolo se utiliza para advertir al usuario sobre la presencia de elementos con

voltaje peligroso sin protección aislante, que puedan encontrarse dentro de la caja

o alojamiento del producto, y que puedan representar riesgo de electrocución.

Precaucion

Leer las instrucciones • Leer y analizar todas las instrucciones de operación y seguridad, antes de usar

el equipo.

Conservar las instrucciones • Conservar las instrucciones de seguridad para futura consulta.

Obedecer las advertencias • Todas las advertencias e instrucciones marcadas en el equipo o en la

documentación del usuario, deben ser obedecidas.

Evitar el uso de accesorios • No usar herramientas o accesorios que no sean especificamente

recomendados por el fabricante, ya que podrian implicar riesgos.

Instrucciones de seguridad • Español

Advertencia

Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo de alimentación eléctrica

indicada en el mismo. La alimentación eléctrica de este equipo debe provenir de un sistema de

distribución general con conductor neutro a tierra. La tercera pata (puesta a tierra) es una medida de

seguridad, no puentearia ni eliminaria.

Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida de alimentación

eléctrica al equipo, desenchufar todos los cables de alimentación en el panel trasero del equipo, o

desenchufar el módulo de alimentación (si fuera independiente), o desenchufar el cable del

receptáculo de la pared.

Protección del cables de alimentación • Los cables de alimentación eléctrica se deben instalar en lugares

donde no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos.

Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal calificado. En el interior

no hay partes a las que el usuario deba acceder. Para evitar riesgo de electrocución, no intentar

personalmente la reparación/mantenimiento de este equipo, ya que al abrir o extraer las tapas puede

quedar expuesto a voltajes peligrosos u otros riesgos.

Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento, es para evitar el

sobrecalientamiento de componentes internos sensibles. Estas aberturas nunca se deben obstruir con

otros objetos.

Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición incorrecta. Cambiar esta

batería únicamente con el mismo tipo (o su equivalente) recomendado por el fabricante. Desachar las

baterías usadas siguiendo las instrucciones del fabricante.

ᅝܼ乏ⶹ

•

Ё᭛

䖭Ͼヺোᦤ⼎⫼᠋䆹䆒໛⫼᠋᠟ݠЁ

᳝䞡㽕ⱘ᪡԰੠㓈ᡸ䇈ᯢǄ

䖭Ͼヺো䄺ਞ⫼᠋䆹䆒໛ᴎ໇ݙ᳝

䴆ⱘॅ䰽⬉य़ˈ᳝㾺⬉ॅ䰽

⊼ᛣ

䯙䇏䇈ᯢк•

䑩ㅸỀ䑩嬦嫿⡈↎⼆枼敆嬼⶷䍇夤ㆁ㙊

⫊₩⏍Ề䑩嬵㕏ɿ

ֱᄬ䇈ᯢк• 䑩ㅸⷕ἞⪙⫊₩嬵㕏ᶧḦ⡈⭇㚦Ề䑩ɿ

䙉ᅜ䄺ਞ • 䑩ㅸⷕ徶⫉ᷨ␂⏍䑩ㅸ㉈⊘ᵋ䗅ㆁ㙊⫊₩

⏍㐎ẝ嬵㕏ɿ

䙓ܡ䗑ࡴ

•

ᵎ壂Ề䑩嬦ᷨ␂⋃⒇㯢㙊㋩劑䗅⴦₸ㅗ弾

⇡嫿⡈澤Ḧ忀₎⊲斪

ɿ

ㅗḼẖ㋦ⅱⵃ䑶䰼丠䗅

ᵻ忀₎℻䋱大䑶⊲斪

ᵎ壂䑩Ḽẖᵝ壀㉢Ẑ彛

㉊䂨䑠ᷨ⋃

䄺ਞ

⬉⑤• 嬦嫿⡈⌫倾Ề䑩ᷨ␂ᵋ㝈㕏䗅䑶㷑ɿ嫿⡈⼆枼

Ề䑩㙊♱一䗅Ờ䑶䰼丠Ờ䑶ɿ

䩭ᵊ㚢一澠♱一澡㕰

⫊₩嫿㓾澤ᵎ倾ᵎ䑩ㅗ崴弈ɿ

ᢨᥝ⬉⑤

• ᵻ⫊₩♱ḏ嫿⡈㈕㋊䑶㷑澤嬸㈕㋊ㆁ㙊嫿

⡈⍏ㅗ㞍暣䑶㷑䗅䑶㷑一澤

䑶㷑一ɿ

⬉⑤㒓ֱᡸ• ⣦Ⓟⵄ一澤忀₎埬嵪嵐澤ㅗ愎䆪㉥⋌ɿ

㓈ᡸ• ㆁ㙊丵Ἧ⼆枼䑲嫥嬂䗅丵Ἧ᷻⎙弜垍ɿ嫿⡈⃆

怩㯢㙊䑩ㅸ⌰Ḧ㘵㊣䗅昷ḷɿ

ᵎ壂儫ⴲ嬖☿㆔⹁嫿⡈䘗⪑丵Ἧ嬦嫿⡈ɿ

䗮亢ᄨ• 㙊ᷜ嫿⡈㙻⠴ᵋ㙊彛栏㤾ㅗ⪕澤⫄ḭ㕰䑩㚦

敳㪣㙻⃆㒐だ₄ḷ弈䀮ɿ

栏⪕ɿ

䫖⬉∴• ᵎ㪤䞯䗅㘵㊣䑶㮡ṛ㙊䅇㿹䗅⊲斪ɿ⼆枼Ề䑩

ᵏ⋃⫷㋩劑䗅䘹⍍ㅗ䘹弒⛌⌸䗅䑶㮡ɿ

䗅⸻嫯⡅䍇ⷠ⹄䑶㮡ɿ

ɿ

QS-1MGP 462 • Quick Start

Quick Start — MGP 462, cont’d

R

/R-Y

G

/Y

B

/B-Y

HVS

R

/R-Y

G

/Y

B

/B-Y

HVS

R

/R-Y

G

/Y

B

/B-Y

HVS

R

/R-Y

G

/Y

B

/B-Y

HVS

RGBHV RGBS

RGsB HDTV Component Video

BNC output connectors

Step 5

Plug the MGP 462, input devices, and output

devices into a grounded AC source, and power

on the input and output devices.

MGP 462 connection diagram

Step 6

Use the LCD menu screens and Adjust knobs to

configure the MGP 462 and adjust the picture

controls (see the following section, Configuring

and Adjusting the MGP 462). See chapter 2 for

installation instructions, chapter 3 for front panel

operation information, chapter 4 for control via

the RS-232/422 interface, and chapter 5 for

Ethernet control.

Quick Start — MGP 462

Installation

Step 1

Install the four rubber feet on the bottom of the

MGP 462, or mount the unit using the supplied

rack mounting brackets.

Rack mounting the MGP 462

Step 2

Turn off power to the input and output devices,

and remove the power cords from them.

Step 3

Attach the input devices to the MGP 462. The

inputs can accept the following signal types:

Inputs 1, 2, 3, 4 — RGB, component video,

S-video, or composite video

Inputs 3 and 4 — Component video, S-video, or

composite video

Input 5 — S-video or composite video

Input 6 — S-video (4-pin mini DIN connector),

composite video (VID BNC connector), or SDI

(MGP 462D model only)

RGBHV

Video

RGsB or

Component

Video

S-Video

Composite

Video

RGBS or

RGBcvS

Video

H/HV

V

R/R-Y

G/Y

VID

B/C

B-Y

H/HV

V

R/R-Y

G/Y

VID

B/C

B-Y

H/HV

V

R/R-Y

G/Y

VID

B/C

B-Y

H/HV

V

R/R-Y

G/Y

VID

B/C

B-Y

H/HV

V

R/R-Y

G/Y

VID

B/C

B-Y

Input connectors

Rack-mount

Bracket

50/60 Hz

100-240

V 0.3A

RGB/R-Y, B-Y,

Y

LAN

RESET

RS-232/422

2

1

R

/

R

-Y

R

/

R

-Y

G

/Y

V

ID

B

/C

B

-Y

H

/

H

V

G

/Y

V

ID

B

/C

B

-Y

H

/

H

V

4

3

R

/

R

-Y

R

/

R

-Y

R

/

R

-Y

G

/Y

V

ID

G

/

Y

B

/

B

-Y

B

/C

B

-Y

H

/

H

V

ID

/Y

V

ID S

D

I

5 6

G

/Y

V

ID

B

/C

B

-Y

H

/

H

V

R

-Y

/C

V

B

-Y

Y

C

H

V

S

I

N

P

U

T

S

O

U

T

P

U

T

S

50/60 Hz

100-240V 0.3A

R

G

B

/R

-Y

,

B

-Y

,

Y

L

A

N

R

E

S

E

T

R

S

-2

3

2

/4

2

1

R/

R-Y

R/

R-Y

G/Y

VID

B/C

B-Y

H/

HV

V

G/Y

VID

B/C

B-Y

H/

HV

V

4

3

R/

R-Y

R/

R-Y

R/

R-Y

G/Y

VID

G

/

Y

B/

B-Y

B/C

B-Y

H/

HV

VID

/Y

V

VID

SDI5

6

G/Y

VID

B/C

B-Y

H/

HV

R-Y

/C

V

B-Y

YCH

V S

I

N

P

U

T

S

O

U

T

P

U

T

S

CODEC

DVD

Video Camera

Control

System

Plasma

Extron

MGP 462

Multi-Graphic Processor

Extron

RGB 109xi

Interface

PC

Laptop

Broadcast VTR

Projector

TCP/IP

Network

Step 4

Attach an output device to the

RGBHV/YUV BNC connectors

(shown below) and/or to the

15-pin HD output connector

(shown at right).

RGB/R-Y, Y, B-Y

Quick Start — MGP 462, cont’d

MGP 462 • Quick StartQS-2

Quick Start — MGP 462, cont’d

Main Menu flow

c. Press the Window/Image Size button

once, and turn the Adjust knobs to the

right until they stop. The window size

setting displays the same resolution as the

output.

d. Repeat steps a through c for the

remaining window.

With both windows at full screen size,

you must mute window 2 in order to set

window 1, and vice versa.

Power

on

Multi-Graphic

Processor

Input

Configuration

2 sec.

MENU

Output

Configuration

MENU

20 sec.

Window

Configuration

MENU

20 sec.

Default

Cycle

Extron

MGP 462 V2.01

2 sec.

Advanced

Configuration

20 sec.

MENU

Press Next

Window Text

Configuration

MENU

20 sec.

Background

Capture

MENU

20 sec.

Auto

Image

MENU

20 sec.

60 sec.

Configuring the MGP 462

Step 1

Use the Input Configuration menu to configure

each of the six inputs.

Step 2

Use the Output Configuration menu to configure

the output signal type and the output rate for the

desired resolution.

Step 3

From the Advanced Configuration menu, Test

Pattern submenu, select the Alternating Pixels

(Alt. Pixels) test pattern. Adjust your display’s

total pixel and phase settings for maximum

picture quality.

Step 4

From the Advanced Configuration menu, change

the test pattern to Crop, and adjust your

display’s positioning until all four sides of the

crop pattern are visible.

Adjusting the picture

controls

Step 5

Use the Window Configuration menu to select a

window border color for each window. This will

aid in window sizing and positioning.

Step 6

Select input 1 for both windows.

Step 7

Adjust windows 1 and 2 to full screen:

a. Press the Window 1 or the Window 2

button to select the window to adjust.

b. Press the Window/Image Position button

once, and turn the Adjust knobs until both

the H and V values = 0000.

Getting Started

After you have installed and

connected the MGP 462, follow

these steps to configure and

adjust it to get it ready for use.

QS-3MGP 462 • Quick Start

Quick Start — MGP 462, cont’d

Step 8

For each input, size and position the image

within both window 1 and window 2.

a. Press one of the six input buttons in the

top row (for window 1) or the bottom row

(for window 2).

b. Press the window button that corresponds

with the input button that you pressed

(e.g., if you pressed the top input 3 button

in step 1, press the Window 1 button).

c. Press the Window/Image Size or the

Window/Image Position button twice.

The LCD window displays the number of

the input whose image you are sizing or

positioning.

d. Rotate the Adjust knobs until the H and V

values represent the image dimensions or

position coordinates you want for the

selected input.

e. Repeat steps c and d as needed to refine

the size and position adjustments for the

selected input.

f. Repeat steps a through e for the same

input in the other window.

g. Repeat steps a through f for each

remaining input.

Auto Image

Auto Image provides a quick way to size an

input to fit the current window size. To auto-size

an image, follow these steps:

a. Press the numbered button for the input

that you want to auto-size.

b. Press the Menu button once to select the

Auto Image menu.

c. Press the Next button to display the Auto

Image selection screen in the LCD window.

d. Turn either Adjust knob to select

window 1 or 2.

e. Press the Next button again to implement

your selection.

Step 9

Use the Input Configuration menu to make any

desired advanced adjustments, including

Horizontal and Vertical Start, Pixel Phase, Total

Pixel, Active Pixel, and Active Lines. See

chapter 3, Operation, for information on these

adjustments.

Step 10

When finished adjusting the desired picture

controls, save your configuration as a window

preset:

a. Press the Preset Recall/Save button

and hold it for at least 2 seconds.

b. Use either Adjust knob to select the preset

number to which you want to save this

configuration.

c. Press the Enter button.

Step 11

You can now size and position windows for each

of your applications and save each one to any

one of the remaining 24 window preset locations

for easy recall of window settings.

You can also save presets using the MGP 462 Web

pages (see chapter 5) or the MGP 462 Windows

®

-

based configuration software (see Windows

®

-based

Configuration Software in chapter 4 for instructions

on accessing the software and its online Help).

Quick Start — MGP 462, cont’d

MGP 462 • Quick StartQS-4

Quick Start — MGP 462, cont’d

i

MGP 462 • Table of Contents

Table of Contents

Chapter 1 • Introduction ....................................................................................................... 1-1

About This Manual ............................................................................................................. 1-2

About the MGP 462/462D................................................................................................ 1-2

Features ................................................................................................................................... 1-2

Application Diagram ......................................................................................................... 1-3

Chapter 2 • Installation .......................................................................................................... 2-1

Mounting the MGP 462 .................................................................................................... 2-2

Tabletop use ....................................................................................................................... 2-2

Rack mounting ................................................................................................................... 2-2

Connecting the MGP 462................................................................................................. 2-3

Installing or Replacing Button Labels ...................................................................... 2-3

Cabling ..................................................................................................................................... 2-4

Input connectors ................................................................................................................ 2-5

LAN connector ................................................................................................................... 2-5

Configuring the LAN port .......................................................................................... 2-6

Reset button and LED ........................................................................................................ 2-6

Remote control connector ................................................................................................ 2-7

Output connectors ............................................................................................................. 2-7

Power connector ................................................................................................................ 2-7

Chapter 3 • Operation ............................................................................................................. 3-1

Front Panel Features ......................................................................................................... 3-2

Power-up and Default Cycle .......................................................................................... 3-3

Input Selection ..................................................................................................................... 3-3

Window Selection Buttons ............................................................................................ 3-4

Menus, Configuration, and Adjustments ............................................................... 3-4

Menu system overview ...................................................................................................... 3-4

Using the menus ................................................................................................................ 3-4

Auto Image menu .............................................................................................................. 3-6

Input Configuration menu ................................................................................................ 3-6

Input configuration submenu adjustments ............................................................... 3-8

Output Configuration menu ............................................................................................. 3-9

Resolution and Refresh Rate submenu .................................................................... 3-10

Output Type submenu .............................................................................................. 3-11

Sync Polarity submenu .............................................................................................. 3-11

Window Configuration menu ......................................................................................... 3-11

Window Priority submenu ........................................................................................ 3-11

Window 1 Border and Window 2 Border submenus .............................................. 3-12

Window Effect submenu .......................................................................................... 3-12

Available effects .................................................................................................. 3-12

Effect Duration submenu ......................................................................................... 3-13

ii MGP 462 • Table of Contents

Table of Contents, cont’d

Window Text Configuration menu ................................................................................. 3-14

Window Text Position submenu............................................................................... 3-14

Window Text Size submenu ..................................................................................... 3-14

Windows 1 and 2 Text Color submenus ................................................................... 3-14

Windows 1 and 2 Text Background submenus ........................................................ 3-15

Windows 1 and 2 Text Border submenus ................................................................ 3-15

Windows 1 and 2 Text Label screens ........................................................................ 3-15

Background Capture menu ............................................................................................. 3-16

Memory space for background files ........................................................................ 3-16

Saving a background to memory ............................................................................. 3-16

Recalling a background from memory .................................................................... 3-17

Advanced Configuration menu....................................................................................... 3-17

Background Color submenu ..................................................................................... 3-18

Blue Mode submenu ................................................................................................. 3-18

Test Pattern submenu ............................................................................................... 3-18

Serial Port Mode submenu ....................................................................................... 3-19

Internal Temperature screen .................................................................................... 3-19

Factory Default submenu ......................................................................................... 3-19

Picture Controls ................................................................................................................. 3-19

Adjusting the picture controls ........................................................................................ 3-20

Memory Presets ................................................................................................................. 3-21

Window presets ............................................................................................................... 3-21

Saving a window preset ........................................................................................... 3-21

Recalling a window preset ....................................................................................... 3-22

Default presets .......................................................................................................... 3-23

Input presets .................................................................................................................... 3-23

Additional Functions....................................................................................................... 3-24

Freeze mode ..................................................................................................................... 3-24

Front panel security lockout (executive mode) .............................................................. 3-24

Resetting the unit ............................................................................................................ 3-24

Chapter 4 • Software Configuration and Control ................................................ 4-1

Setting Up RS-232 / RS-422 Communication .......................................................... 4-2

Using Simple Instruction Set (SIS

™

) Commands .................................................. 4-2

Host-to-MGP communications .......................................................................................... 4-2

MGP-initiated messages .................................................................................................... 4-2

Error responses ............................................................................................................ 4-3

Error response references ........................................................................................... 4-3

Telnet and Web communications...................................................................................... 4-3

Symbol definitions ............................................................................................................. 4-5

Command/response table for SIS commands ................................................................... 4-8

Command/response table for IP control port commands .............................................. 4-18

Using the Windows

®

-based Control Software .................................................... 4-31

Installing the software .................................................................................................... 4-31

Starting the control program .......................................................................................... 4-33

Using the Button Label Generator ........................................................................... 4-34

iiiMGP 462 • Table of Contents

Chapter 5 • Ethernet Configuration and Control ................................................. 5-1

Accessing the Web pages................................................................................................ 5-2

Viewing System Status .................................................................................................... 5-3

Using the Configuration Pages .................................................................................... 5-4

System Settings screen ....................................................................................................... 5-4

IP Settings fields .......................................................................................................... 5-4

Unit Name field ..................................................................................................... 5-4

DHCP radio buttons ............................................................................................... 5-4

IP Address field ...................................................................................................... 5-5

Gateway IP Address field ...................................................................................... 5-5

Subnet Mask field .................................................................................................. 5-5

MAC Address field ................................................................................................. 5-5

Setting the date and time .......................................................................................... 5-5

Scaler Settings screen ........................................................................................................ 5-6

Input configuration .................................................................................................... 5-7

Naming inputs ....................................................................................................... 5-7

Selecting the video signal type ............................................................................. 5-7

Output configuration ................................................................................................. 5-7

Window configuration ............................................................................................... 5-7

Parameters with separate menus for Window 1 and Window 2 ........................ 5-8

Advanced configuration ............................................................................................. 5-8

Background capture ................................................................................................... 5-8

Passwords screen ................................................................................................................ 5-9

Assigning a password ................................................................................................. 5-9

Clearing a password .................................................................................................... 5-9

Email Alerts screen ........................................................................................................... 5-10

Setting up SMTP authorization ................................................................................ 5-11

Firmware Upgrade screen ............................................................................................... 5-11

Determining the current firmware version ............................................................. 5-11

Downloading the firmware ...................................................................................... 5-12

Updating the firmware on the MGP 462 ................................................................. 5-12

Using the File Management Page ............................................................................. 5-14

Uploading files ................................................................................................................. 5-14

Adding a directory ........................................................................................................... 5-14

Other file management activities ................................................................................... 5-15

Using the Control Pages ................................................................................................ 5-15

User Control screen .......................................................................................................... 5-15

Select Window .......................................................................................................... 5-15

Input Selection .......................................................................................................... 5-15

Window Mute ........................................................................................................... 5-16

Executive Mode ......................................................................................................... 5-16

Freeze ........................................................................................................................ 5-16

Film Mode .................................................................................................................. 5-16

Picture Controls – Window ....................................................................................... 5-16

Picture Controls – Image ........................................................................................... 5-17

iv MGP 462 • Table of Contents

Table of Contents, cont’d

Window Presets screen .................................................................................................... 5-18

Naming a window preset ......................................................................................... 5-19

Saving (creating) a window preset .......................................................................... 5-19

Recalling a window preset ....................................................................................... 5-19

Input Presets screen ......................................................................................................... 5-19

Saving (creating) an input preset ............................................................................. 5-20

Recalling an input preset .......................................................................................... 5-20

Chapter 6 • Special Application........................................................................................ 6-1

Connecting the MGP 462 to a Matrix Switcher ................................................... 6-2

Setting up the MGP to work with the switcher ............................................................... 6-3

Synchronizing the MGP 462 to the matrix switcher ........................................................ 6-4

Additional setup procedures if using a third party control system

without the MGP Sync tool ............................................................................................... 6-5

Appendix A • Specifications and Part Numbers ................................................... A-1

Specifications....................................................................................................................... A-2

Included Parts ...................................................................................................................... A-4

Accessories ............................................................................................................................ A-4

Appendix B • Installing the SDI Card ............................................................................B-1

Installing a Serial Digital Interface (SDI) Card.....................................................B-2

Appendix C • Firmware Update Guide.........................................................................C-1

Determining the Firmware Version ...........................................................................C-2

Using the LCD display at power-on .................................................................................. C-2

Using a Web browser......................................................................................................... C-2

Using the Windows-based control software ....................................................................C-3

Downloading the Firmware .......................................................................................... C-4

Updating the Firmware....................................................................................................C-4

Updating using the Web pages ........................................................................................ C-5

Updating using the Windows-based control software ....................................................C-6

68-840-01 Rev C

08 06

All trademarks mentioned in this manual are the properties of their respective owners.

MGP 462 Multi-Graphic Processor

1

Chapter One

Introduction

About This Manual

About the MGP 462/462D

Features

Application Diagram

Introduction, cont’d

MGP 462 • Introduction1-2

Introduction

About This Manual

This manual discusses how to install, operate, and configure the Extron MGP 462

multi-graphic processor.

Throughout this manual, the terms “MGP,” “multi-graphic processor,” and

“processor” are used interchangeably to refer to the same product.

About the MGP 462/462D

The MGP 462 is a six-input, one-output RGB and video processor that can display

two video sources on a single screen in picture-in-picture or picture-by-picture

format. It provides switching among inputs, picture controls, and presets.

The MGP accepts RGB video, component video, S-video, and composite video

inputs. The MGP 462D is an MGP 462 with an SDI board installed so that input 6

can also accept SDI signals. (See appendix B, Installing the SDI Card, for information

on installing this board.)

Both versions can be controlled remotely via the RS-232/RS-422 interface using

Special Instruction Set (SIS

™

) commands or via an Ethernet LAN using the

MGP 462’s embedded Web pages. The MGP 462 Windows

®

-based control software

program can also be used to control the MGP via either the RS-232/422 or the

Ethernet connection.

Features

Inputs — The MGP 462 has six video inputs: fully configurable inputs 1 through 4

accept RGB, component, S-video, and composite video signals; input 5

accepts component video, S-video, and composite video; and input 6 accepts

S-video and composite video. The MGP 462D model also accepts SDI signals

on input 6.

Output — The MGP 462 has one scaled RGB or HD YUV output, available on both

a 15-pin HD connector and a set of five BNC connectors. This enables two

output devices to be connected to the MGP at the same time (both displaying

the same image).

Picture controls — Picture controls allow you to adjust size, position, brightness,

contrast, color, tint, detail, and zoom for each window.

Window and input presets — Window presets save sizing, positioning, and

priority information. Input presets save input signal type information and

picture control settings.

Window transition effects — Six types of window transition effects (22 different

effects altogether) seamlessly mute and unmute (close and open) the two

windows.

Freeze control — Freeze control freezes (locks) a window to the current image.

3:2 pulldown detection for NTSC video and 2:2 film detection for PAL video —

These advanced film mode processing features help maximize image detail

and sharpness for video sources that originated from film.

When film is converted to NTSC video, the film frame rate has to be matched

to the video frame rate in a process called 3:2 pulldown. Jaggies and other

image artifacts can result if conventional deinterlacing techniques are used

on film-source video. The MGP 462’s advanced film mode processing

recognizes signals that originated from film. The MGP then applies video

processing algorithms that optimize the conversion of video that was made

with the 3:2 pulldown process. This results in richly detailed images with

sharply defined lines.

1-3MGP 462 • Introduction

A similar process, 2:2 film detection, is used for PAL film-source video.

Background image capture, save, and recall — Background Capture enables you to

capture and save the image currently on the output screen. You can then

recall the captured image and display it as a background later.

Auto Image

™

— Auto Image automatically sizes, centers, and optimizes the image

to the scaled output rate, filling the window.

Remote control — The MGP 462 can be operated remotely via the RS-232/422

interface using the Windows-based control software or SIS commands, or via

the Ethernet interface using the embedded Web pages.

Rack mounting — The 1U high and full rack wide metal enclosure can be rack

mounted using the included rack mounting brackets (part #70-077-03).

Front panel security lockout (executive mode) — Locks the front panel controls to

prevent accidental changes to the unit’s settings.

RGB and video scaling — All sources are scaled to a single output rate.

Application Diagram

The application diagram below gives an example of how devices may be connected

to the MGP 462.

50/60 Hz

100-240V 0.3A

RGB/R-Y,

B-Y,

Y

LAN

RESET

RS-232/422

2

1

R/

R-Y

R/

R-Y

G/Y

VID

B/C

B-Y

H/

HV

V

G/Y

VID

B/C

B-Y

H/

HV

V

4

3

R/

R-Y

R/

R-Y

R/

R-Y

G/Y

VID

G/

Y

B/

B-Y

B/C

B-Y

H/

HV

VID

/Y

V

VID

SDI5

6

G/Y

VID

B/C

B-Y

H/

HV

R-Y

/C

V

B-Y

YC H

V S

I

N

P

U

T

S

O

U

T

P

U

T

S

CODEC

DVD

Video Camera

Control

System

Plasma

Extron

MGP 462

Multi-Graphic Processor

Extron

RGB 109xi

Interface

PC

Laptop

Broadcast VTR

Projector

TCP/IP

Network

Connection diagram

Introduction, cont’d

MGP 462 • Introduction1-4

MGP 462 Multi-Graphic Processor

2

Chapter Two

Installation

Mounting the MGP 462

Connecting the MGP 462

Installing or Replacing Button Labels

Cabling

Installation, cont’d

MGP 462 • Installation2-2

Installation

Mounting the MGP 462

Tabletop use

Four self-adhesive rubber feet are included with the MGP 462. For tabletop use,

attach one foot to each corner of the bottom side of the unit and place the MGP in

the desired location.

Rack mounting

The MGP can optionally be mounted in a rack with the supplied MBD 149 rack

mounting kit (part #70-077-03). Follow these steps:

1. Attach the mounting brackets to the unit using eight of the machine screws

supplied with the mounting kit.

Rack-mount

Bracket

50/60 Hz

100-240

V 0.3A

RGB/R-Y,

B-Y,

Y

LAN

RESET RS-232/422

2

1

R

/

R

-Y

R

/

R

-Y

G

/Y

V

ID

B

/C

B

-Y

H

/

H

V

G

/Y

V

ID

B

/C

B

-Y

H

/

H

V

4

3

R

/

R

-Y

R

/

R

-Y

R

/

R

-Y

G

/Y

V

ID

G

/

Y

B

/

B

-Y

B

/C

B

-Y

H

/

H

V

ID

/Y

V

ID

S

D

I5 6

G

/Y

V

ID

B

/C

B

-Y

H

/

H

V

R

-Y

/C

V

B

-Y

Y

C

H

V

S

I

N

P

U

T

S

O

U

T

P

U

T

S

Attaching the mounting brackets

2. Insert the unit into the rack and align the holes in the mounting brackets with

the holes in the rack. Use four of the supplied machine screws to attach the

brackets to the rack.

Rack Mount

Bracket

Rack mounting the MGP 462

2-3MGP 462 • Installation

Connecting the MGP 462

The MGP 462 processor can be connected to as many as six input devices

simultaneously, and two output devices (displaying the same image). Follow the

steps below to set up the MGP 462 hardware.

1

Disconnect power to the MGP, and turn off all other devices that will be

connected.

2

If the MGP 462 is to be mounted, see Mounting the MGP 462, earlier in this

chapter, for the mounting procedure.

3

Using the BNC input connectors, attach up to six video input devices to the

MGP rear panel.

S-video and composite video inputs cannot both be connected to input 6 at the

same time.

4

Connect one or two output devices to the RGBHV/YUV BNC output

connectors and/or to the 15-pin HD connector.

5

If the MGP 462 will be connected to a computer or to a host controller for

remote control, connect the host’s RS-232 cable to the processor’s 9-pin

RS-232/422 D-sub connector.

6

Connect an active LAN Ethernet cable to the RJ-45 port on the rear panel to

establish a link to the network.

7

Power up the input and output devices, then connect power to the processor.

Installing or Replacing Button Labels

You may wish to customize your MGP’s buttons. The button caps are pre-labeled

for your convenience, but you can replace any of these labels with one of the

included button labels. You can also create custom labels using the Button-Label

Generator software (see Using the Button Label Generator in chapter 4, Software

Configuration and Control), or device such as the Brother P-Touch label maker. Cut

the labels so that they are square and ½ inch on each edge.

The button assembly consists of a clear lens cap, the button label, and a white

diffuser. (See the illustration on the next page.)

Follow these steps to replace button labels on your MGP:

1. Cut out the desired button label from the provided sheet, or make new labels

using the Button-Label Generator or other software and cut them out.

2. Remove the button assembly by inserting a small, flat-bladed screwdriver,

such as an Extron Tweeker, between the button’s base and the diffuser to

gently pry the button assembly off the button plunger.

3. Locate the small corner notch on the lens cap, and slide the screwdriver

between the lens cap and the diffuser. (See

a

in the illustration on the next

page.)

4. Using a rotating motion of the screwdriver, carefully pry the two pieces apart.

(See

b

in the illustration on the next page.)

Installation, cont’d

MGP 462 • Installation2-4

2

1

TEXT

Separate the two-

piece button at

the corner.

Pry the two

pieces apart.

Diffuser

Plunger

Base

Button Label

Clear Lens

Notch

Replacing a button label

5. Lift out the transparent square label that you want to replace. You may need

to use the small screwdriver to gently pry the label out.

Do not pry off the translucent diffuser that is behind the label.

6. Insert one of the new label you created in step 1 into the clear button cap,

align the white backing plate with the cap, and firmly snap it into place.

7. Gently, but firmly, press the reassembled button into place on the MGP front

panel.

8. Repeat steps 1 through 7 as needed to relabel other buttons.

Cabling

5

50/60 Hz

100-240V 0.3A

RGB/R-Y, Y, B-Y

LAN

RESET RS-232/422

2

1

R/

R-Y

R/

R-Y

G/Y

VID

B/C

B-Y

H/

HV

V

G/Y

VID

B/C

B-Y

H/

HV

V

4

3

R/

R-Y

R/

R-Y

R/

R-Y

G/Y

VID

G/

Y

B/

B-Y

B/C

B-Y

H/

HV

VID

/Y

V VID SDI 5 6

G/Y

VID

B/C

B-Y

H/

HV

R-Y

/C

V B-Y YC H V S

I

N

P

U

T

S

O

U

T

P

U

T

S

4

6

8

9

1

2

3

6

7

MGP 462D rear panel (The MGP 462 is identical except that there is no SDI

connector [

d

].)

2-5MGP 462 • Installation

Input connectors

1

Inputs 1, 2, 3, and 4 — Plug RGB, component video, S-video, or composite

video sources into these BNC connectors as shown in the diagram below.

RGBHV

Video

RGsB or

Component

Video

S-Video

Composite

Video

RGBS or

RGBcvS

Video

H/HV

V

R/R-Y

G/Y

VID

B/C

B-Y

H/HV

V

R/R-Y

G/Y

VID

B/C

B-Y

H/HV

V

R/R-Y

G/Y

VID

B/C

B-Y

H/HV

V

R/R-Y

G/Y

VID

B/C

B-Y

H/HV

V

R/R-Y

G/Y

VID

B/C

B-Y

Connector signal types for inputs 1 through 4

2

Input 5 — Plug a component video, S-video, or composite

video source into these BNC connectors.

3

Input 6 — Plug an S-video source into the 4-pin mini DIN

connector (in bottom row) or a composite video source into

the VID BNC connector (in top row).

Connecting S-video and composite video devices to input 6

simultaneously causes degraded output display quality.

4

SDI input — (MGP 462D only) Plug an SDI device into this

SDI BNC connector, as an alternative to input 6.

LAN connector

5

LAN connector — Plug an RJ-45 network cable into this connector to connect

the unit to a network (via a switch, hub, or router) or to a single computer.

Use a straight-through cable to connect to a network, or a crossover cable to

connect directly to a computer.

• For 10Base-T (10 Mbps) networks, use a Cat 3 or better cable.

• For 100 Base-T (max. 155 Mbps) networks, use a

Cat 5 cable.

See the illustration on the next page for information on

wiring the connector for these two types of cables..

Activity LED — This yellow LED blinks to indicate

network activity.

Link LED — This green LED lights to indicate a good

network connection.

LAN

RJ-45

Port

Link

LED

Activity

LED

VID

/Y

5

R-Y

/C

B-Y

VID

6

VID

SDI

6

YC

B-Y

VID

SDI

6

YC

B-Y

Installation, cont’d

MGP 462 • Installation2-6

Clip Down

1

1&2

3&6

4&5

7&8

23 45678

123 45678

RJ-45

Connector

Twisted

Pairs

Straight-through Cable

(for connection to a switch, hub, or router)

End 1 End 2

Pin Wire Color Pin Wire Color

1 white-orange 1 white-orange

2 orange 2 orange

3 white-green 3 white-green

4 blue 4 blue

5 white-blue 5 white-blue

6 green 6 green

7 white-brown 7 white-brown

8 brown 8 brown

Crossover Cable

(for direct connection to a PC)

End 1 End 2

Pin Wire Color Pin Wire Color

1 white-orange 1 white-green

2 orange 2 green

3 white-green 3 white-orange

4 blue 4 blue

5 white-blue 5 white-blue

6 green 6 orange

7 white-brown 7 white-brown

8 brown 8 brown

Pin assignments for LAN connector and cables

Configuring the LAN port

You also need to configure the LAN port before using it. This is done with SIS

commands. See Command/Response table for IP control port commands in chapter 4 for

information on these commands.

The LAN port defaults are:

Processor IP address: 192.168.254.254

Gateway IP address: 0.0.0.0

Subnet mask: 255.255.0.0

DHCP: off

Reset button and LED

6

Reset button and LED — Pressing this recessed button causes certain IP

functions and Ethernet connection settings to be reset to the factory defaults.

The green LED above the button blinks a varying number of times to indicate

which reset mode has been entered. See Resetting the unit in chapter 3,

Operations, for information on reset modes.

Page is loading ...

Extron electronic MGP 462D User manual

This manual is also suitable for

Extron electronic MGP 462D User manual

Related papers

Other documents