Messoa NDR721 Quick start guide

Page is loading ...

1

English

1 Product Overview

1.1 Physical Description & Connection

Connections

Product Side ViewProduct Front View

DC Power

LAN

Lens

IR LED

Slide lock

Cable side cover

A

B

A

1. Identify the type of network device.

2. If the network device supports PoE (Power over Ethernet) function, simply connect the camera to it via Ethernet cable.

3. If not, both Ethernet cable and DC adaptor should connect to device

2

English

2 Installation

2.1

Package Content

2.2

Installation

2.2.1 Mounting the Camera

The Camera

Ceiling Mount Installation Pack

Quick Installation Guide

Screws & Anchors

Alignment Sticker

Lens adjustment tool

A

B

C D

1. Place the alignment sticker on the ceiling which was preferred and drill three holes into the ceiling for cable and screws

2. Connect and route Ethernet cable or DC cable through the ceiling

(Note: remove the cable side cover once the cable route from the side)

3. Attach the camera to the ceiling by two screws.

(Note: The torque of electric screwdriver is recommended less than 6kgf-cm.)

4. Place the cover into the camera and ensured it locked.

Lens direction indicator

321 4

Indoor IR Dome Network Camera

Quick Start

Guide

201409 721 A1

NDR721

3

English

2.2.2 Tuning the Camera

1. Push the slide lock rightward to remove the dome cover

2. Adjust tilt angle by turning tilt adjustment screws

3. Fit the lens adjustment tool to lens and tune up focus by adjustment tool

4. Place the dome cover into camera module and ensured it locked

Rotate

Tilt adjustment screw

Focus

3

2

1

4

3

Connection

3.1 Assigning IP Address

2. Check the checkbox to select a camera device from the list.

3. The IP Camera may be assigned with a valid IP address via DHCP server. It can be also manually given a static IP address.

To do so, click on “Set IP”, and then input the IP, Subnet Mask and Gateway. Input account info if the camera is password

protected. (Default ID/Password : admin/1234)

4. Click on the “Browse” button to get access to the camera web page immediately.

1. Launch Discovery Tool (IPCAMDiscovery.exe). The tool will start searching and then displaying the cameras on the

Device List after they are found.

30

admin

4

English

3.2 Accessing the Camera

2. The live video of the camera can be played with a RTSP player, such as VLC or QuickTime. The network URL is rtsp://

Camera IP/stream1. The example given below is that live video is displayed with QuickTime player.

1. Launch IE browser and input the IP address of the camera, or click on “Browse” button on Discovery Tool.The web page

with video will then be shown as below.

3.3 Wireless Setting

3.3.1 Manual Setup

Note

USB WiFi Dongle as optional parts for WiFi function

4. Once the setting complete, disconnect the Ethernet cable and then reboot the camera.

3. Type in the SSID and shared key same as what set on your router/AP and click the save button.

1. If the network device supports PoE function, simply connect the camera to it via Ethernet cable.

Otherwise both Ethernet cable and DC cable should connect to device.

2. Enter the web page setup > Network > Wireless

Choose the AP which want to be connected and click the “Select”

5

English

3.3.2 WiFi Direct Mode for mobile device

2. Scan the camera AP from smart phone/tablet WiFi Setup menu and link to the camera WiFi AP.

1. Press WiFi Mode button on camera over 1 sec but less than 3 sec, Amber LED turns on. The camera will act as a WiFi AP at

meantime.

3. Access the camera web page http://192.168.1.1/mobile by browser or scan the QR code as below Enter to “WiFi setting”

to type in the SSID and shared key same as what set on your WiFi router/AP and click the save button

4. The camera WiFi will switch back to client mode and link with the congured WiFi router/AP automatically.

6

English

3.3.3 WPS Function

WPS

1. Press the WPS (WiFi Protected Setup) button on your WiFi router/AP to trigger connection function

2. Press WiFi mode button on camera over 3 seconds then LED1 and LED2 starts to ash (the Amber LED and Green LED

start to ashing every 1 second which only last 2 minutes)

3. Once successful connection or WPS function timeout (2 minutes), the LED2 (Green) keeps steady on

Page is loading ...

Messoa NDR721 Quick start guide

Messoa NDR721 Quick start guide

in other languages

Related papers

Other documents