Page 1 of 2
PLA Channel - Installation Instructions
Please read all instructions prior to installation and keep for future reference!
1. Product should be installed by a qualified electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
3. If extrusion is installed facing up and in a wet location, ensure proper drainage and silicone
endcaps and diffuser lens.
REV0.0 10072019
*OPTIC ARTS BY LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE
T 224.333.6033
www.opticarts.com
solder
pads
If required to fit the new PLA extrusion length, cut down the
LineLED strip/s in between two rows of solder pads. Always
cut LineLED from end without connector/wire leads. Ensure that
LineLED strip/s fit completely inside the extrusion and the solder
pads do not touch the metal endcaps to avoid shorting of circuit.
wire
leads
1
Always wear safety goggles when cutting. If required for
installation cut the aluminum extrusion to desired length with
hacksaw or miter saw that has an appropriate blade for
cutting aluminum.
Ensure aluminum extrusion is
clean from dust before taping
the LineLED strip/s. If necessary
wipe extrusion and let dry before
installing. Locate LineLED strip/s
as close as possible to extrusion
ends to avoid dark spots.
2
mounting
holes min of
30” apart
Ensure appropriate drill
bit is used to drill in the
aluminum extrusion. Drill
location for mounting holes
(min. qty. 2) at appropriate
intervals and within the
groove in the middle of
the extrusion. Also, ensure
hole for electrical wiring is
located where needed.
5feed LineLED
wire leads
through one of
drilled holes
remove LineLED
paperbacking
from adhesive
tape before
installing into
extrusion
If joining multiple extrusions. Insert the
PLA-JOIN (sold separately) half way into one
of the extrusion ends. Followed by pushing
one of the extrusion next to the other extrusion.
Repeat step for any additional connections.
LineLED strip
4
3
PLA extrusion
PLA-JOIN
Page 2 of 2
PLA Channel - Installation Instructions
Please read all instructions prior to installation and keep for future reference!
1. Product should be installed by a qualified electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
3. If extrusion is installed facing up and in a wet location, ensure proper drainage and silicone
endcaps and diffuser lens.
REV0.0 10072019
*OPTIC ARTS BY LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE
T 224.333.6033
www.opticarts.com
power to LineLED
of PLA extrusion
Class 2
power
supply
line voltage wires low voltage wires
6Use included
fasteners
to install
endcaps onto
extrusion.
Use No.4 1/2” long fasteners
to mount extrusion through drilled
mounting holes. Once extrusion is
in place, snap-on diffuser lens and
finally remove its protective film.
diffuser
lens
7
Ensure power is off to power supply! Then proceed to connect
LineLED wires from PLA extrusion to power supply. Refer to
power supply and LineLED wiring instructions.
protective film
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
luminii SLW36 Channel Installation guide
-
luminii LL42WET-T User manual
-
-
luminii LL18WET User manual
-
-
luminii LLHE48WET-T User manual
-
-
-
-
Other documents
-
KLUS KOPRO-30 User manual
-
KLUS PDS-4-PLUS User manual
-
KLUS MICRO-HG Operating instructions
-
Robus REXA172-23 User manual
-
-
KLUS Exemplary LED Extrusion User manual
-
KLUS GIZA-LL Operating instructions
-
GE ZISW48D Installation guide
-
Grandio Greenhouses ELITE-8 User manual
-
MakerBot Replicator 2x User manual
