6
6.1
6.1 Clean extrusion from any debris.
6.2 If applicable, feed LineLED wires through the extrusion hole. Remove
the paper backing from the adhesive tape on the LineLED before installing
the extrusion.
extrusion
LED
1
Please read all instructions prior to installation and keep for future reference!
1. Product to be installed by a qualied electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Models CLAC-XX-S-XX & CLAC-XX-Q-XX
Page 1 of 2
1.1 Snap the lens into the extrusion, then align & center the extrusion to the
determined location. Make all necessary markings to install to the surface.
extrusion measure & then mark
reference points
Note: Complete fixture must be assembled prior to install. To properly make
all necessary reference marks & to ensure all parts are included. Then it can be
taken apart for installation.
lens
measure
reference mark
1.1
aluminum
extrusion
Caution: Safety equipment is recommended, when modifications are being
made to the extrusion & lens.
2.1 If necessary extrusion with the lens installed can be cut in the field.
Use the proper blade for aluminum, and then cut to the desired length.
extrusion
with lens
2
2.1
4.1 Ensure the appropriate drill bit is used
to drill in the aluminum extrusion.
Drill location for mounting holes every
30” or at least 2 screws per extrusion
from within the center of the extrusion.
Drill another hole to either the extrusion
or endcaps for LineLED wires to feed
through to power supply.
solder pads
3.1 LineLED can be shortened by cutting along the dashed lines in between
the solder pads. Make sure the cut is made on the side of the LineLED
without the wire leads. LineLED cannot touch the metal endcaps which will
shorten the circuit.
cut
LineLED
cut
3.1
wire leads
LineLED
3
3.1
STEP A STEP B STEP C
tighten at head screws below
extrusion surface before
installing LineLED
drill locations
for mounting
holes
countersink
holes for
at head
screws
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
extrusion
4
4.1
aluminum
extrusion
5.1 Secure the extrusion directly to wall with the appropriate hardware.
5
extrusion
screw
4.1
REV0.1 10112018
2.1
lens
extrusion
5.1
miter saw
CLA Channel - Installation Instructions
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Page 2 of 2
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
9.1 Ensure the correct (wattage & voltage) power supply is used to
power LineLED. Then proceed to connect LineLED wires from
extrusion to power supply. For more information please refer to
power supply and LineLED wiring instructions.
9
line voltage wires low voltage wires
class II power
supply
LineLED
extrusion
9.1
7.1 Snap the lens into the extrusion.
7
extrusion
7.1
8.1 Push the endcaps into the extrusion ends to secure.
8
extrusion
8.1
endcaps
lens
Please read all instructions prior to installation and keep for future reference!
1. Product to be installed by a qualied electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
REV0.1 10112018
CLA Channel - Installation Instructions
Models CLAC-XX-S-XX & CLAC-XX-Q-XX
CLA
Channel
Varies Lens
options
square
(CLAC-XX-S-XX) rounded square
(CLAC-XX-Q-XX)
lens
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
luminii LL42WET-T User manual
-
luminii SLW36 Channel Installation guide
-
luminii LLHE48WET-T User manual
-
-
luminii LL18WET User manual
-
-
-
-
-