Louroe Electronics AOP-SP-CF Installation And Operating Instructions Manual

Category
Motorcycle Accessories
Type
Installation And Operating Instructions Manual
AOP-SP-CF
Ceiling Mount
Flush
2-Way Speakerphone
AOP-SP-CS
Ceiling Mount
Surface
2-Way Speakerphone
AOP-SP-CF/CS 8/09
Louroe Model AOP-SP-CF/CS is a ceiling mount speakerphone designed to provide 2-way audio
(listen/talkback) with various modes of audio/video transmission systems such as:
DVR’s
IP Network Cameras
PC Soundcards
Video Servers
Louroe companion unit AOP-XD Transceiver Interface maybe used but not required with the above
speakerphones. The unit can be used as a standalone equipment and can be directly connected to
an IP Camera, DVR or Video Server.
Refer to accompanying AOP-XD instructions for connections and operating instructions when used
with the AOP-SP-CF or AOP-SP-CS.
The AOP-SP-CF/CS provides line level audio input and output. It has amplifier that drives the built-
in 4” speaker. A 12 Vdc, 500mA power supply is required for this unit.
E
LOUROE
LECTRONICS
6955 VALJEAN AVE, VAN NUYS, CA 91406
PH: (818)994-6498 / FAX: (818)994-6458
[email protected] / www.louroe.com
AOP-SP-CF / AOP-SP-CS
SPEAKERPHONE
INSTALLATION AND OPERATING INSTRUCTIONS
Page 1 of 8
The gain of the microphone and speaker are factory adjusted. If it is necessary to change the gain
of either or both the audio output of the microphone and speaker of the unit, it has to be done in
small increments. For adjusting the gain of the microphone, rotate clockwise to increase or
counterclockwise to decrease, the potentiometer marked “MIC” slowly until the desired level is
attained. Somebody at the head-end has to listen to it while the adjustments are made. If the
microphone’s gain is too high, it will attenuate the audio output of the speaker. The output of the
speaker will then be cutting off as you talk. If this happens, rotate the potentiometer marked “MIC”
slowly counterclockwise to decrease the gain of the microphone until the talkback sound at the
speaker no longer cuts off.
To adjust the audio output of the speaker, rotate the “SPKR” potentiometer clockwise (increase) or
counterclockwise (decrease) slowly until the desired loudness is attained. If the audio from the
microphone becomes attenuated, rotate the “SPKR” potentiometer counterclockwise a small
increment at a time until the microphone audio becomes louder again.
DESCRIPTION
OPERATIONS
Page 2 of 8
LOUROE ELECTRONICS 6955 VALJEAN AVE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
Website: www.louroe.com Email: [email protected]
(818)
Color Code of recommended wiring is:
RED - 12Vdc power to microphone
BLACK - Audio Output
BARE - Ground
WHITE - Speaker
Color Code may vary among wire manufacturers
block marked A, B, C, SP
A = 12Vdc power (red wire)
B = Audio output (black wire)
C = Ground (bare wire)
SP = Speaker Connection (white wire)
Bring one end of recommended cable and connect as follows:
Located on the bottom right side of PC board is a 4-pin terminal
WIRING CONNECTION TO SPEAKER AND MICROPHONE OF AOP-SP CF/CS
WIRING CONNECTION TO AOP-SP (CF OR CS Models)
WIRING CONNECTION FROM AOP-SP-CF OR AOP-SP-CS TO
COMPANION AOP-XD AUDIO INTERFACE UNIT
1) Connect RED wire to terminal marked “A”
2) Connect BLACK wire to terminal marked “B”
3) Connect BARE wire to terminal marked “C“
4) Connect WHITE wire to terminal marked “SP“
The rear panel of the AOP-XD has a 4-pin terminal block marked A, B, C, SP
Bring in other end of cable and connect as follows:
1) Red wire to terminal A of AOP-XD
2) Black wire to terminal B of AOP-XD
3) Bare wire to terminal C of AOP-XD
4) White wire to terminal SP of AOP-XD
(Patch Cables not included)
On the back panel of Model AOP-XD are two sets of Audio In/Audio Out Jacks - RCA and 3.5mm type.
Either one can be used to connect to the Audio In/Audio Out of the DVR, IP Camera, Video Server, etc.
Using the appropriate patch cables, connect as follows:
1) Audio Out of AOP-XD connects to Audio In of receiving device
2) Audio In of AOP-XD connects to Audio Out of receiving device
This completes the wiring between the AOP-SP-CF/AOP-SP-CS and AOP-XD. For operation instructions
regarding Model AOP-XD Transceiver Interface Unit, refer to the AOP-XD instructions that accompany the unit.
See diagram next page
WIRING REQUIREMENTS
3 Conductor consisting of:
+
2 Conductor shielded, 20 gauge
with 22 gauge drain
+
1 Conductor unshielded, 20 gauge
All in the same jacket
INSTALLATION AND OPERATING INSTRUCTIONS
See diagram next page
CONNECTION FROM AOP-XD TO THE RECEIVING DEVICE (DVR, IP CAMERA, ETC.)
AOP-SP-CF/CS 8/09
LOUROE ELECTRONICS 6955 VALJEAN AVE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
Website: www.louroe.com Email: [email protected]
(818)
BACK SIDE OF AOP-SP UNIT
INSTALLATION AND OPERATING INSTRUCTIONS
Page 3 of 8
WHITE
BLACK
+24Vdc, 1A
BARE
RED
ABCSP
INPUT
To “Audio In” of
DVR, IP Network
Camera, Video
Server, etc.
Optional 3.5mm
audio input/output to
DVR, IP Network
Camera, Video Server, etc.
To “Audio Out” of
DVR, IP Network
Camera, Video
Server, etc.
MODEL AOP-XD
AUDIO INTERFACE UNIT
(rear panel)
INTERCONNECTION DIAGRAM
BETWEEN LOUROE MODEL AOP-SP-CF/AOP-SP-CS
AND
AOP-XD AUDIO TRANSCEIVER INTERFACE
INPUT INPUT
AUDIO
AUDIO
OUTPUT
OUTPUT
A
U
D
I
O
P
A
T
H
A
U
D
I
O
P
A
T
H
RCA Plug
Color Code of recommended wiring is:
RED - 12Vdc power to microphone
BLACK - Audio Output
BARE - Ground (microphone)
WHITE - Speaker
+24 Vdc, 1A
POWER SUPPLY
(INCLUDED)
Microphone
Connection
Terminal Block Identifier
A = 12Vdc power
B = Audio Output
C = Ground
SP = Speaker Connection
}
WIRING REQUIREMENTS
3 Conductor consisting of:
+
2 Conductor shielded, 20 gauge
with 22 gauge drain
+
1 Conductor unshielded, 20 gauge
All in the same jacket
ELECTRET
CONDENSER
MICROPHONE
RED (A)
BLACK (B)
BARE (C)
WHITE (SP)
+12Vdc
TALKBACK
ADJUST
MIC
ADJUST
C
A
SP
B
PC Board
of AOP-SP-CF
or
AOP-SP-CS
AOP-SP-CF/CS 8/09
INTERCONNECTION DIAGRAM
CONNECTING LOUROE MODEL AOP-SP-CF/CS
DIRECTLY TO AN IP CAMERA, DVR,
VIDEO SERVER, ETC. USING 3-COND. SHIELDED CABLE
EXT
MIC SPKR +12Vdc
AUDIO
OUT
AUDIO
IN
TALKBACK
ADJUST
MIC
ADJUST
C
A
SP
B
LOUROE MODEL AOP-SP-CF/CS
PC BOARD
WHITE (SP)
BLACK (C)
(C) BARE
(B) RED
TO AUDIO OUT OF IP CAMERA, DVR, ETC.
TO AUDIO IN OF IP CAMERA, DVR, ETC.
NOTE: BLACK AND BARE WIRES ARE COMMON GROUND
BARE (C)
BLACK (C)
RED (B)
4-PIN TERMINAL BLOCK IDENTIFIER OF AOP-SP-CF/CS (A,B,C,SP)
( ) B = Audio Output
( ) C = Ground (audio) and Ground (speaker) (black wire)
( ) SP = Speaker output
A = not used with this application
red
bare
white
West Penn 358
or equivalent
C
A
SP
B
WHITE (SP)
Audio Out
Audio Out Audio In
Audio In
Bare Wire
Red Wire
RCA CONNECTION
3.5mm MONO CONNECTION
3.5mm STEREO CONNECTION
White Wire
Black Wire
Black Wire
White Wire
Red Wire
Bare Wire
M
O
N
O
S
T
E
R
E
O
Audio Out
Audio In
Red Wire
Black Wire
White Wire
Bare Wire
WIRING REQUIREMENTS
3 Conductor consisting of:
+
2 Conductor shielded, 20 gauge
with 22 gauge drain
+
1 Conductor unshielded, 20 gauge
All in the same jacket
+12Vdc,500mA power required
(AD-1 power supply included)
AUDIO
OUT
AUDIO
IN
AOP-XD is not used for this application.
Page 4 of 8
LOUROE ELECTRONICS 6955 VALJEAN AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
Website: www.louroe.com Email: [email protected]
(818)
12 Vdc power is required to connect the AOP-SP-CF/CS
directly to an IP camera or DVR such as AD-1 power supply.
Positive 12Vdc (wire with white stripe) connects to terminal
marked “+
Negative 12 Vdc or ground connects to terminal marked
GND
AOP-SP-CF/CS 8/09
INSTALLATION AND OPERATING INSTRUCTIONS
INTERCONNECTION DIAGRAM
CONNECTING LOUROE MODEL AOP-SP-CF/CS (STAND ALONE)
DIRECTLY TO AN IP CAMERA
USING 3-COND. SHIELDED CABLE TERMINATED WITH 3.5mm PLUG
INSTALLATION AND OPERATING INSTRUCTIONS
3.5mm MONO CONNECTION
White Wire
Red Wire
M
O
N
O
Audio In
Audio Out
Red Wire
Black Wire
White Wire
Bare Wire
WIRING REQUIREMENTS
3 Conductor consisting of:
+
2 Conductor shielded, 20 gauge
with 22 gauge drain
+
1 Conductor unshielded, 20 gauge
All in the same jacket
+12Vdc
AUDIO
OUT
AUDIO
IN
TALKBACK
ADJUST
MIC
ADJUST
C
A
SP
B
LOUROE MODEL AOP-SP-CF/CS
PC BOARD
TO AUDIO IN OF IP CAMERA
TO AUDIO OUT OF IP CAMERA
+12Vdc, 500mA, power required
(AD-1 Power supply included)
IP NETWORK CAMERA
audio input audio output
AOP-XD is not used for this application.
12 Vdc power is required to connect the AOP-SP-CF/CS
directly to an IP camera or DVR such as AD-1 power supply.
Positive 12Vdc (wire with white stripe) connects to terminal
marked “+
Negative 12 Vdc or ground connects to terminal marked
GND
An adaptor (mono to stereo) maybe is
needed if the output of the IP camera has
a stereo jack.
Page 5 of 8
LOUROE ELECTRONICS 6955 VALJEAN AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
Website: www.louroe.com Email: [email protected]
(818)
Two 3.5mm cables is included that
can be use if the distance
between the AOP-SP-W and the IP
camera is 3’ or less. Otherwise, the
recommended cable should be
used and terminated with 3.5mm
mono plugs on both ends.
AOP-SP-CF/CS 8/09
MOUNTING ASSEMBLY
FOR
LOUROE MODEL AOP-SP-CS SPEAKERPHONE
CEILING MOUNT - SURFACE
5/32”
Pem
Nut
NOTE
Screws for securing
mounting ring
to ceiling
not supplied
by Louroe Electronics
8 x 32
Phillips
(4 supplied)
BR-8 Grill
12 ? ” dia
Speaker
Assy
4-pin terminal
block
Model MR-8
Surface
Mounting Ring
Mounting Bracket
Installation Steps
First make electrical connections to speakerphone 4-pin
terminal block
Install mounting ring to ceiling
Mount grill to mounting ring
LOUROE ELECTRONICS 6955 VALJEAN AVE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
Website: www.louroe.com Email: [email protected]
(818)
INSTALLATION AND OPERATING INSTRUCTIONS
Page 6 of 8 AOP-SP-CF/CS 8/09
BR-8 Grill
12 7/8” dia
Speaker
Assy
LOUROE ELECTRONICS 6955 VALJEAN AVE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
Website: www.louroe.com Email: [email protected]
(818)
Ceiling Tile
Flexible Perforated
Steel Mounting Straps (4)
ERD-8 Backbox
MOUNTING ASSEMBLY
FOR
LOUROE MODEL AOP-SP-CF SPEAKERPHONE
CEILING MOUNT - FLUSH
8 x 32
Phillips
(4 supplied)
4-pin terminal
block
INSTALLATION AND OPERATING INSTRUCTIONS
Page 7 of 8 AOP-SP-CF/CS 8/09
LOUROE ELECTRONICS 6955 VALJEAN AVE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
Website: www.louroe.com Email: [email protected]
(818)
SPECIFICATIONS (Microphone)
Audio output
Microphone element sensitivity
Line level (0 dB @ 600)
unbalanced
-45 dB
Frequency response
Audio Input Impedance
40 Hz - 10 kHz
600
SPECIFICATIONS (Mechanical)
AOP-SP - CF/CS (grill)
AOP-SP-CF (backbox) for flush mount
Inside
Flange
12 7/8” (327mm)
9 ¾” (247mm)
12 5/16” (313mm)
AOP-SP-CS MR8 (Mounting Ring)
for surface mount
12 3/8” X 3”H (314mm H x 76mm)
Depth 4 ½” (114mm)
INSTALLATION AND OPERATING INSTRUCTIONS
Electret Condenser
Type
Weight,net (AOP-SP-CF) 2.5 Lbs ( 1.1 Kg)
Weight, (AOP-SP-CS) with MR-8 5 Lbs (2.3 Kg)
SPECIFICATIONS (Speaker)
Speaker power output
Speaker impedance
Speaker magnet
Speaker size
1.5W
8
3 oz. ceramic
4” (102mm)
Current Drain
Supply Voltage
200mA
12Vdc
AOP-SP-CF/CS 8/09
Page 8 of 8
WARRANTY
LOUROE ELECTRONICS warrants that at the time of shipment products manufactured by LOUROE ELECTRONICS to be free of defects in material and workmanship.
Should a defect appear within one year (12 months) from date of shipment, LOUROE ELECTRONICS will, at its sole discretion, repair or replace the defective equipment.
This equipment shall not be accepted for repair or return without prior notification by LOUROE ELECTRONICS.
This warranty does not extend to any Louroe product that has been subjected to improper or incorrect installation, misuse, accident, or in violation of installation
instructions provided by LOUROE ELECTRONICS.
Returned shipments to LOUROE ELECTRONICS shall be at customer’s expense. LOUROE ELECTRONICS will return the equipment prepaid via best way.
IMPORTANT NOTICE
When this equipment is used as part of an audio
monitoring system, the law requires that the public
be given notice of AUDIO MONITORING ON THE
PREMISES. A decal notice is included with each
microphone shipped.
Federal Law References:
Federal Regulations, US Code, Title 18.
Crime and Criminal Procedure, Sec 2510.
AUDIO
MONITORING
E
LOURO E
LECTR ONICS
On
These Premises
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Louroe Electronics AOP-SP-CF Installation And Operating Instructions Manual

Category
Motorcycle Accessories
Type
Installation And Operating Instructions Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI