Louroe Electronics DigiFact® A Operating instructions

Brand
Louroe Electronics
Model
DigiFact® A
Type
Operating instructions
Page 1 of 2
6955 VALJEAN AVE, VAN NUYS, CA 91406
PH: (818)994-6498 / FAX: (818)994-6458
[email protected], www.louroe.com
®
Digifact A, LE-870, NEMA
ROUND ADAPTER PLATE
INSTRUCTIONS
Part No: 00-LE870-BRKT
A
L
G
D
B
C
H
I
The Louroe Round NEMA Adapter Plate (LE-870NRIP, Ref. B) provides a (LE-870
Digifact A IP Microphone) to mount to a standard rectangle or round style NEMA J-Boxes, and match to the same
mounting hole patterns. This is required for most state and local C7-C10 professionals, that conforms to safety - electrical
standards and codes.
Steps 1-4
1.) Attach the Louroe NEMA Adapter Plate (00-LE870-BRKT) to the NEMA standard rectangle or round J-Box, with (2 x
Screws, Not Supplied). Observe the mating position of the plate in reference to the Digifact A, (LE-870). The Louroe Logo
must match the Orange Dot Ref (E) when the Digifact A, (LE-870) is attached, see Ref (H) location on the (00-LE870-
BRKT). This is important so that the cabling for the RJ45 and Digital I/O ports can pass thru the rectangle opening in the
plate. Install and adjust the (00-LE870-BRKT) adapter plate using the Slotted Screw Hole Cutouts, (D+G) so you can
align the adapter plate to the J Box as needed, Ref (C) properly. 2.) Pull the Ethernet and Digital I/O cable (If Applicable)
thru the rectangle cable opening Ref (I). 3.) Connect the male RJ45 connector of your ethernet cable to the RJ45 jack on
the Digifact A, (LE-870), then connect the Digital I/O cables to the 10 position terminal block (If Applicable). 4.) Push the
extra cable back thru the rectangle cable opening Ref (I) and then install the Digifact A, (LE-870), Ref (A) to the NEMA
Adapter Plate (00-LE870-BRKT) Ref (B) using the (4 x Screws, Supplied) Ref (L) through holes (J1-4) in alignment with
holes Ref (B) (K1-4).
seamless mounting solution for the
Assemby Process
Installation References (A-K)
(A) Digifact A, LE-870, (B) NEMA Interface Plate
NEMA Slotted Screw Hole Cutouts, (E) Louroe Allignment Logo, (F) Blue Multi-Function Indicator L.E.D., (H) Orange Dot
indicates Top-Front of the Round NEMA adapter plate, (I) Access to Ethernet Connectivity, Digital I/O ports, (J 1-4)
Digifact A, LE-870 screw holes, (K 1-4) Digifact A, LE-870 Mounting holes, (L) 4 x 6-32, 1-3/8” Sheet Metal Screws.
(00-LE870-BRKT), (C) NEMA Standard J-Box, (D)+(G) Adjustable
Diagram 1A.
Please Note!
Works with all Metal-Plastic,
NEMA Standard Rectangle
or Round J-Boxes
®
F
J
E
J 1-4
K 1-4
Louroe
Digifact A, LE-870
Industry Standard
Round NEMA J-Box
Louroe 00-LE870-BRKT
NEMA Round
Adapter Plate
00-LE870-BRKT, 12052023-WB
6955 VALJEAN AVE, VAN NUYS, CA 91406
PH: (818)994-6498 / FAX: (818)994-6458
www.louroe.com[email protected],
®
6.0” (Dia.)
Louroe
Electronics
Logo
DIGIFACT ‘A’
LE-870 J-Box
00-LE870-BRKT
NEMA Round
Adapter Plate,
B
RJ45, 10 Position
Terminal
Block Access
Ref. Only
Alignment
Reference
Page 2 of 2
Template Reference
Actual Size 1:1
Package Content
Specifications
1 x Round Steel NEMA
Adapter Plate, 4 x 6-32, 1-3/8” Sheet
Metal Screws.
00-LE870-BRKT
Material: Steel
Size-Diameter: 6.0”
Thickness: 0.06”
NEMA: National Electrical Manufacturers Association. Defines-Outlines electrical
standards used in North America for specifications used by LV-HV manufactures
for electronic-electrical enclosures and plate hole spacing/sizing.
Digifact A, LE-870, NEMA
ROUND ADAPTER PLATE
Part No: 00-LE870-BRKT
Front View
Slotted Screw
Hole Cutout #1
to NEMA J Box
Orange
Allignment Dot
Slotted Screw
Hole Cutout #2
to NEMA J Box
Digifact A, LE-870
Mounting Holes A-D
REFERENCE
00-LE870-BRKT, 12052023-WB
A
B
C
D
  • Page 1 1
  • Page 2 2

Louroe Electronics DigiFact® A Operating instructions

Brand
Louroe Electronics
Model
DigiFact® A
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents