2. Skov
  3. Replacement of 10 inch display

Skov Replacement of 10 inch display Technical User Guide

  • Hello! I'm a chat assistant that has read the Technical User Guide for the 10" Display replacement. This document provides step-by-step instructions for mounting, backing up data and other parameters, and calibrating the display for your controller. I'm ready to answer any questions you might have about the replacement process or the display itself.
  • What tools are recommended for display replacement?
    Is it necessary to back up existing data before display replacement?
    What should be checked after the display is replaced?
Replacement of 10" Display
Technical User Guide
604377 • 2020-11-27
Replacement of 10" Display
1 Product description........................................................................................................................................4
2 Mounting guide...............................................................................................................................................5
2.1 Recommended tools.................................................................................................................. 5
2.2 Preparing for replacement ........................................................................................................ 5
2.3 Backup of existing setup and data........................................................................................... 5
2.4 Replacing the display ................................................................................................................ 7
2.5 Checking and calibration ........................................................................................................ 12
3 Maintenance guide .......................................................................................................................................13
4 Technical data...............................................................................................................................................14
Technical User Guide
Replacement of 10" Display
4 Technical User Guide
1 Product description
This is a 10” spare parts display for a controller.
Replacement of 10" Display
Technical User Guide 5
2 Mounting guide
2.1 Recommended tools
Below follows a list of tools recommended for the installation.
Item Description
Cross-head screwdriver
Screwdriver straight slot (two)
Installation, servicing and troubleshooting of all electrical equipment must be carried out by quali-
fied personnel in compliance with the applicable national and international standard EN 60204-1
and any other EU standards that are applicable in Europe.
The installation of a power supply isolator is required for each motor and power supply to facilitate
voltage-free work on the electrical equipment. The power supply isolator is not included.
2.2 Preparing for replacement
When replacing, you have to use the following new parts:
• Display
• Front foil
• Mounting tool
• Any SD card for backup
2.3 Backup of existing setup and data
SKOV A/S recommend that backup of historical data is set to take place automatically once a day. This ensures
that a new backup will always be available. The automatic backup takes place at 1:30 a.m.
Although the house controller is set to backup automatically, it can be an advantage to make a new backup just
before the replacement is carried out. This ensures that the latest data is transferred.
Make a note of the main module and CAN protocol setup in the menu | Technical | Installation | Man-
ual installation | I/O modules.
If necessary, take photos of the pages and the installation menu Show connection ( | Technical | Instal-
lation | Show connection).
Note or take pictures of the values of the following settings (*If installed).
Function Preset value
House name
Temperature setpoint
Heat offset setpoint*
Humidity setpoint*
Minimum ventilation/animal
Batch day number
Number of animals
Main module
CAN protocol
If the controller is connected to a network with FarmOnline Explorer
IP setup
UTC time and UTC date
Replacement of 10" Display
6 Technical User Guide
(A)
(B)
(C)
1. Remove the front panel screws (A) to release the panel.
2. Make sure not to pull the flat cable so that the plug (B) is damaged.
3. Insert an SD card in the SD port of the CPU module (C) if a card is not already inserted.
4. Save the current setup before replacement.
5. Select Save settings and pages in the menu | Technical | Service | Settings | Backup | SD card.
6. Select Save FarmOnline data in the menu | Technical | Service | Settings | Backup | SD card.
7. Wait until the house controller indicates that the setup is saved.
8. Remove the SD card from the controller.
Replacement of 10" Display
Technical User Guide 7
2.4 Replacing the display
(G)
(F)
(F) (G)
Replacement of 10" Display
8 Technical User Guide
Removing the CPU module
1. Remove the front panel screws (A) to release the panel.
2. Disconnect the network connector on the CPU module (C), if the controller is part of a network.
3. Disconnect the flat cable (B) from the main module (H).
Place the panel on a stable surface where you can complete the replacement.
1. Click off the protective cap (D) to release it from the CPU module (C); use a screwdriver as shown in picture
(E).
2. Click off the CPU module (C) as shown in the picture below. Click off the CPU module in the side with the
network connector (LAN). Carefully tilt it up and turn it upside down.
3. Disconnect the LVDS flat cable (F) and touch flat cable (G) (press the connectors on the flat cables up in
both sides).
Replacement of 10" Display
Technical User Guide 9
(J) (F) (G)
(G)
(FF)
(FF)
(I)
Removing the display
1. Place the panel with the front facing up. Remove the old display foil by pulling it off from one of the corners.
It is essential to ensure that the surface is level. It may, therefore, be necessary to remove any residue of
glue.
2. Position the panel with the reverse side facing up.
3. Remove the tape (I) that holds the touch flat cable (G) thus the flat cable is removed with the display.
4. Remove the tape (I) that holds the LVDS flat cable (F).
5. Remove the LVDS flat cable (F) on the display plug (FF) by tilting the lock upwards.
6. Loosen the display by pressing it with a screwdriver through a stud hole (J).
7. Insert a screwdriver under the display while pressing from the back and break free the display. Tilt under the
metal and not under the glass, which may splinter. Be careful not to damage the panel.
Replacement of 10" Display
10 Technical User Guide
(K)
(G)
Mounting the display
It is essential to have good light and a stable surface to replug the connectors accurately.
Try to put the display on first without taping it. Once the tape protection has been removed, you cannot readjust
the position of the display.
1. Place the manufacturer-supplied mounting tool (K) in the corner where you run the flat cables of the display.
2. Bend the flat cables (L) of the display forward and run them through the panel.
3. Put down the display and push it up against the tool to ensure that there is the same distance all the way
around.
4. Tilt the display up and remove the tape protection. Be careful when placing the display again.
Replacement of 10" Display
Technical User Guide 11
(M)
(N) (G)
(F)
(G)
(F) (FF)
(F) (G) (FF)
(I)
Mounting the front foil
1. Mount the front foil (M). The tape protection (N) on the back of the foil is split. Only remove the tape protec-
tion on one side. Place the front foil loosely and adjust it in place. Press the foil firmly in the side where the
tape protection was removed. Remove the remaining tape protection and press the foil firmly all the way
around.
2. Also, remember to remove the narrow inner foil. Please carefully fasten both foils so that it becomes com-
pletely waterproof.
3. Turn the panel upside down.
4. Connect the LVDS flat cable (F) on the new display plug (FF).
5. Mount tape (I) on the LVDS flat cable (F) and touch flat cable (G).
Replacement of 10" Display
12 Technical User Guide
Mounting of other parts (see illustrations above)
1. Connect the LVDS flat cable (F) and touch flat cable (G) on the CPU module (press the connectors on the
flat cables down in both sides).
2. Mount the CPU module (C) on the panel.
3. Mount the protective cap (D) on the CPU module (C).
4. Reconnect the flat cable (B) on the main module (H).
5. Connect the network connector on the CPU module (C), if the controller is part of a network.
6. Mount the panel on the cabinet using the panel screws (A).
7. Power the controller.
2.5 Checking and calibration
It is crucial to check that the climate controller is working as it did before, as simple connections can be
switched around. The climate controller provides a warning, but it does not indicate, which connection
has been moved.
If there are animals in the livestock house, it is imperative to check the noted values after the update,
so that the day number and all other settings are correct.
Confer the technical manual for instructions on checking and calibration if the climate controller does not start
up again, as usual.
Replacement of 10" Display
Technical User Guide 13
3 Maintenance guide
There is no maintenance of software.
The functions from the feature software are not overwritten by a subsequent software update but are updated
together with the latest update.
It is not possible to uninstall feature software once it is installed.
Replacement of 10" Display
14 Technical User Guide
4 Technical data
Environment
Operating temperature °C (°F) -10 to +45 (+14 to 113)
Storage temperature °C (°F) -25 to +60 (-13 to +140)
Relative humidity, operation % RH 0-80
Shipment
Dimensions H x W x D mm 247 x 166 x 5
Packing dimensions H x W x
D
mm 310 x 230 x 100
Weight g 430
Shipping weight g 600
604377 • 2020-11-27 • en-US • Made in Denmark
SKOV A/S • Hedelund 4 • Glyngøre • DK-7870 Roslev
Tel. +45 72 17 55 55 • www.skov.com • E-mail: [email protected]
/