Argos Virgo Multi Media Storage Shelf Assembly Instructions Manual

Brand
Argos
Model
Virgo Multi Media Storage Shelf
Type
Assembly Instructions Manual
Assembly Instructions - Please keep for future reference
Dimensions
Width - 97cm
Depth - 16.8cm
Height - 15cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Virgo Multi Media Storage Shelf
issue 1 4/22/10
875/4097
875/7290
We do not
recommend the use
of power drill/ drivers
for inserting screws,
as this could damage
the unit. Only use hand
screwdrivers.
Warning: The unit weighs
approximately 5kgs.
Please lift with care.
●Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
●From time to time check that
there are no loose screws on this
unit.
●This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
Note: If required the next page
can be cut out and used as a
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
Check you have all the
components and tools listed on
pages 2 and 3.
plastic bags and separate them
into their groups.
Remove all fittings from the
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand on the panels, this
could cause damage.
Assemble the unit as close to its
final position (in the same room)
as possible.
Assemble on a soft level
surface to avoid damaging the unit
or your floor.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging carefully
and responsibly.
Components - Panels
Please check you have all the panels listed below
2
Back (97 x 15cm)
1
Bottom (97x 15cm)
2
Vertical x 5 (14.8 x 12.9cm)
3
If you have damaged or missing components,
call the Customer Helpline:08456 400800
Screw x 19
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Components - Fittings
Please check you have all the fittings listed below
Tools required
Ruler - Use this ruler to help correctly identify the screws
A
B C
D
3
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
105
110 115 120 125 130 135 140 145 150 155 160 165 170
Cover cap x 9
Drill
7mm Masonary drill bit
(for use with wall plug)
Eye protection
(when using a
hammer or glue)
50mm Screw x 4
Wall Plug x 4
Assembly Instructions
Step 1
Constructing the shelf
4
a:
Step 1
a:
Firstly, locate the Back
board . This board has
four pre-drilled holes
which are used to mount
the shelf to a wall after
assembly.
b:
b: Take one Vertical
board and attach it to
the Back board using
Screws .
Note: It would be useful to
ask someone to help you
at this stage.
1
Pre-drilled holes
1
3
3
1
1
A
A
c: Repeat the above
step for the remaining
Vertical boards and
attach them in the same
way.
c:
3
A
3
1
3
A
Assembly Instructions
5
b: To secure Back panel
1 to the Bottom panel
using Screws .
a: Attach Bottom panel
to the unit using Screws
a .A
2
Step 2
Attaching the bottom
and back panel
a:
b:
Note: It would be useful to
ask someone to help you
at this stage.
2
A
A
1
1 2
A
2
Assembly Instructions
6
Mounting the wall unit
a: Choose your preferred
location for the shelving
unit and mark four drill
holes on the wall using
the pre-drilled holes on
the back panel as a
guide.
Drill a hole in the wall at
an appropriate position
and insert Wall plug ,
secure the shelf using
the Screws .
b: Stick the Cover caps
on the screw holes of the
unit.
B
Step 3
a:
3
2
Note: It would be useful to
ask someone to help you
at this stage.
C
D
Important: When drilling
into walls always check
that there are no hidden
wires or pipes etc. Make
sure that the screws and
wall plugs supplied are
suitable for supporting
the unit. Consult a
qualified tradesperson if
you are not sure.
1
1
C
D
b:
Assembly is complete.
If you need help or have damaged or missing parts, call the
Customer Helpline : 08456 400800
B
A Guide to -Wall Mounting & Fixings
Revision 2 - 7/10/09
Important note:
Types of walls
Care &
Maintenance
No.1 “General Purpose” wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
No.3 “Cavity Fixing” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
a specialist ftting in this case. For light
loads, general purpose wall plugs can
be used.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
For use with plasterboard partitions or
hollow wooden doors.
For use when ftting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with walls stuck with
plasterboard. The hammer fxing allows
it to be fxed to the wall rather than the
plasterboard. Always check the fxing
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
Safety: Always check the ftting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the ftting to ensure the wall plugs
or screws do not become loose.
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well ftted and are a tight ft in the
drilled hole.
If plastic wall plugs
are supplied with your
product:
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualifed
tradesperson if you are unsure.
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fxings is the
responsibility of the installer.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Argos Virgo Multi Media Storage Shelf Assembly Instructions Manual

Brand
Argos
Model
Virgo Multi Media Storage Shelf
Type
Assembly Instructions Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents