AmeriHome ABGLIDER4 Operating instructions

Brand: AmeriHome

Model: ABGLIDER4

Type: Operating instructions

This manual is also suitable for

801767

ABGLIDER4

4 Ft Amish Bench Glider

Assembly Instructions

Max Weight Capacity 300 Lb

READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT.

This manual provides important information on proper operation & maintenance. Every effort has been

made to ensure the accuracy of this manual. These instructions are not meant to cover every possible

condition and situation that may occur. We reserve the right to change this product at any time without

prior notice.

IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR UNSAFE,

DO NOT USE THIS PRODUCT!

DO NOT RETURN THIS PRODUCT TO THE RETAILER - CONTACT CUSTOMER SERVICE.

If you experience a problem, have questions or need parts for this product, visit our website

http://www.amerihomebrand.com or call Customer Service at 1-888-287-6981, Monday-Friday,

8 AM - 4 PM Central Time, or email : info@amerihomebrand.com. A copy of the sales receipt is required.

KEEP MANUAL, SALES RECEIPT & WARRANTY FOR FUTURE REFERENCE!

HARDWARE

(A) 4 7/16" Carriage Bolts 2 pieces

(E) Locking Nuts 24 pieces

(G) Washers 24 pieces

TOOLS YOU WILL NEED

• Hammer • 1/2" Ratchet • 1/2" Wrench

PARTS LIST

Right Arm

Rest

(B) 3 15/16" Carriage Bolts 4 pieces

Left Arm Rest

Seat

Spacer

4 Pieces

Base Legs

2 Pieces

(H) Gliding Brackets 4 pieces

(F) Nuts 8 pieces

(I) 3 1/2" Carriage Bolts 6 pieces

(D) 2 1/2" Carriage Bolts 8 pieces

Bench Back

Top Support

2 Pieces

47” Cross Support

2 Pieces

44” Cross Support

1 Pieces

BASE ASSEMBLY

1.!Lay!2!pieces!of!Base!Legs!parallel!to!each!other.!Connect!by!aligning!holes!in!44”!cross!brace!with!holes!in!the!center!

of!each!base!leg.!Place!3!½”!carriage!bolt!through!both!base!leg!and!44”!cross!brace!and!add!washer!and!locking!nut!to!

the!bottom !side!o f!the!b ase !leg.!DO !NO T!T IGH TE N!B OL T.!Yo u!w ill!first!need!to !set!the !carriage !bo lt!by!tap ping !in!place !

with!a!hammer.!You!will!next!flip!over!and!use!½”!long!ratchet!to!make!locking!nut!snug.!You!will!need!to!be!able!to!

adjust!the!legs!in!order!to!make!sure!base!is!square!in!future!steps.!!

2.!Next!you!will!need!to!attach!the!47”!cross!support!to!the!top!supports.!Place!the!47”!cross!braces!parallel!to!each!

other!on!the!ground.!Next!place!the!top!support!on!top!of!the!cross!supports!aligning!the!2!middle!holes!of!the!top!

support!with!the!two!holes!on!the!end s!of!each!cross!suppo rt.!

!!!!!!!!!!! !

Next!you!will!place!a!4!½”!carriage!bolt!through!the!aligned!holes!and!secure!with!a!washer!an d !lo ck in g!n u t!o n !t he !b a ck .!

Be!sure!to!set!carriage!bolt!by!tapping!in!place!with!a!hammer!before!tightening!the!locking!nut!with!a!½”!long!ratchet.!!!

!!! !

3.!Take!the!four!spacers!an d!set!th em !on !top !of!the !bas e!legs!yo u!a ssem b led !in!step!one .!!Be!sure!you!have!aligned!the!

holes!in!base!legs!with!the!holes!in!the!spacers.!!

Carriage Bolts

4.!You!will!now!place!the!part!of!the!base!assembled!in!Step!2!on!top!of!the!spacers.!Be!sure!to!align!the!holes!on!the!

top!support!w ith!th e!ho les!in!th e!spa cers.!S e e!p h o to !be lo w .!!

5.!Next!insert!the!4!pieces!8!7/8”!carriage!bolts!in!each !of !th e !fo u r!h ole s .!It!w ill!r un !t h ro u gh !th e !to p !s u pp o rt ,!th e!s p a ce r!

and!the!leg!base.!You!will!secure!by!taping!in!place!with!a!hammer!and!tighten!using!a!washer!and!locking!nut!on!the!

underside!of!the!base!leg.!See!photos!below.!!

6.!Your!base!should!now!be!squared!and!you!can!complete!tightening!the!two!bolts!from!step!one!on!the!underneath!

side!of!the!leg!base!in!the!center.!!

Carriage Bolts

BENCH ASSEMBLY

1. You!will!need!to!lay!the!bench!seat!on!the!ground!an d!plac e!be nc h!b ack !in!betw e en !the!ex ten sion s!of!the !bas e!

seat.!You!will!need!to!align!the!holes!at!the!back!of!the!bench!seat!and!the!bottom!of!the!bench!back.!Insert!a!3!

½”!carriage!bolt!(from!inside!out)!through!the!bench!back!and!bench!seat.!See!photo!below .!NOTE:!DO!NOT!SET!

CARRIAGE!BOLT!OR!SECURE!WITH!LOCKING!NUT.!THIS!STEP!IS!TO!JUST!HOLD!THESE!TWO!PIECES!TOGETHER!

AND!IN!PLACE!FOR!NEXT!STEP.!

!!!!!!!!!!!!!! !

2. Attach!the!arm!rest!to!the!bench!seat!and!the!bench!back.!!

a. You!will!need!the!box!the!product!was!shipped!in,!left!arm!rest,!right!arm!rest,!2!pieces!4!½”!carriage!

bolt,!2!pieces!3!½”!carriage!bolt!!

b. Place!the!box!the!product!was!shipped!in!on!its!side!and!place!attached!bench!back!and!bench!seat!on!

top!as!show n!in!the !ph oto !be low .!Be!su re!yo u! stab ilize!the!box!so!it!does!not!fall!over!and!damage!the!

product!or!cause!injury.!!

c. Next!you!will!take!the!left!arm!rest!and!insert!a!3!½”!carriage!bolt!in!the!front!leg!of!the!arm!rest!and!a!4!

½”!carriage!bolt!in!the!back!leg!of!the!arm!rest.!You!will!not!push!them!all!the!way!through.!You!will!

insert!the m!just!so !th e y!a re !sh o w in g !o n !th e !o pp o s ite !sid e !o f!th e !w o o d .!T h es e !are !t he !h o le s!midZway!up!

the!leg!of!the!arm !rest.!See !ph oto !belo w .!!

3. You!will!then!align!the!bolts!with!the!preZdrilled!holes!on!the!left!side!of!the !ch a ir!s ea t.!!

Note:!the!bolt!in!the!back !leg!of!the !arm !rest!w ill!run!thro ug h!th e!leg!of!th e!arm !res t,!the!sea t!

bottom!and!the!bottom!of!the!chair!back.!This!should!push!the!3!½”!carriage!bolt!in!the!chair!

back!and!seat!bottom!(which!was!inserted!in!step!1)!out.!!

a. Repeat!steps!2!and!3!on!the!opposite!side!and!tighten.!Use!hammer!to!set!carriage!bolts.!Next!use!½”!

ratchet!to!tighten !all!bolts!w ith!a !wa she r!an d!loc king !nut.!

4. Next!you!will!align!the!preZdrilled!holes!in!the!back!of!the!arm!rest!and!the!midd le!of!th e!ch air!bac k.!!

4 1/2”

Carriage Bolt

in Back Leg

3 1/2”

Carriage Bolt

in Back Leg

Left Arm Rest

a. Insert!3!½”!carria g e!b o lt .!U s e!hammer!to!se t!t h e!c a rria g e !b o lt.!Next!tigh t en !with!w as h e r!a n d !lo c kin g !n u t!

using!½”!wrench.!!

b. Repeat!on!Opposite!side!

ASSEMBLING BENCH AND BASE

1. On!top!support!you!should!still!have!two!holes!in!the!front!and!back.!You!will!take!a!2!½”!carriage!bolt!and!place!

through!eac h!ho le.!Th is!bolt!w ill!run!from !the !inside !ou t.!You !will!nex t!place !a!wa sh er,!regu lar!nu t,!gliding!bra ce,!

and!locking!nut!on!the!carriage!bolt.!Be!sure!to!set!the!carriage!bolt!before!tightening!the!regular!nut!and!

locking!n u t.!!B e !su re !to !n o te !h o w !th e !g lid ing !b ra ck e ts !are !p la ce d !o n !th e !ca rria g e!b o lt!in !b e lo w !p h o to s. !

!!!!!!!! !

Placement of

Gliding Brackets