Lenze TA i900 Owner's manual

Inverter

i950 cabinet servo inverter

Firmware V_1_3_7

"Table Posioning" technology applicaon

Commissioning | EN

Contents

1About this document 15

1.1 Document descripon 15

1.2 Further documents 15

1.3 Notaons and convenons 16

2Safety instrucons 17

2.1 Basic safety instrucons 17

2.2 Applicaon as directed 18

2.3 Handling 18

2.4 Residual hazards 19

3Product informaon 21

3.1 Features 21

3.2 Idencaon of the products 27

3.2.1 Product codes 27

3.2.2 Nameplates 28

3.3 License informaon 29

4Commissioning 30

4.1 Important notes 30

4.2 Operang interfaces 31

4.2.1 Engineering tool »EASY Starter« 32

4.2.1.1 Generate a connecon between inverter and »EASY Starter« 33

4.3 General informaon on parameter seng 34

4.3.1 Addressing of the parameters 34

4.3.2 Structure of the parameter descripons 34

4.3.3 Parameter overview lists 34

4.3.4 Favorites 35

4.3.4.1 Conguring the "Favorites" 35

4.4 Commissioning steps 38

4.4.1 Seng and transferring safety parameters 39

4.5 Saving the parameter sengs 41

4.5.1 Save parameter sengs with »EASY Starter« 41

5Basic seng 42

5.1 Technology Applicaon 42

5.2 Device name 42

5.3 Mains voltage 43

5.4 Funcon assignment of the inputs and outputs (default seng) 43

5.5 Motor data 44

5.5.1 Select motor from motor catalog 45

5.5.2 Manual seng of the motor data 47

5.6 Motor control mode 51

Contents

3

6 Technology applicaon (TA) basic sengs 52

6.1 Kinemac sengs 53

6.1.1 Mass inera (load/motor) 53

6.1.2 Torque feedforward control 53

6.1.3 Motor/encoder mounng direcon 53

6.1.4 Motor/encoder gearbox rao 54

6.1.5 Motor/encoder feed constant 56

6.1.6 Motor/encoder travel ranges and cycle length 57

6.1.7 Virtual mode 59

6.2 Moon sengs 60

6.2.1 Quick stop 60

6.2.2 Halt 61

6.2.3 Following error monitoring 61

6.2.4 Target posion detecon 62

6.2.5 Motor/encoder standsll detecon 62

6.2.6 Condioning of the encoder signal 62

6.2.7 Behaviour in the event of inverter disable 63

6.2.8 Control modes 64

6.2.9 Manual jog (inching mode) 65

6.2.10 Homing 66

6.2.10.1 Homing modes 68

6.2.10.2 Digital input for reference switch 77

6.2.10.3 Motor/encoder behaviour aer mains switching 77

6.2.11 Limitaons 78

6.2.11.1 Torque limits 78

6.2.11.2 Maximum values for travel proles 79

6.2.11.3 Hardware limit switches 80

6.2.11.4 Soware limit switches 81

6.2.11.5 Safety limits 82

6.2.12 Dead me compensaon 84

6.2.13 Status signals 84

6.3 Dening control sources 86

6.3.1 Source of quick stop 86

6.3.2 Source of error reset 87

6.3.3 Source of digital output 1 87

6.3.4 Source of monitoring signal 88

6.4 System bus communicaon 89

6.4.1 Inputs 89

6.4.2 Outputs 89

6.4.2.1 Master value output 90

6.4.2.2 Source of touch probe me stamp 91

6.4.3 Distribuon of the master values by the master 92

6.4.3.1 Example: System bus master is master value master 93

6.4.3.2 Example: System bus slave is master value master 94

6.4.3.3 Example: Using me stamp of another axis 95

6.5 Monitoring 96

Contents

4

7Conguring the "Table Posioning" TA 97

7.1 Control sengs 98

7.2 Interface 99

7.2.1 Control signals 100

7.2.2 Status signals 101

7.2.3 Simulaon of the interface 103

7.3 Travel proles 105

7.3.1 Technology applicaon travel prole parameters 106

7.3.2 External travel prole parameters 110

7.3.3 Travel prole linkage 112

7.4 Signal ow 112

7.5 Funcons 113

7.5.1 Posioning modes 114

7.5.1.1 Absolute posioning 114

7.5.1.2 Absolute posioning in clockwise direcon 115

7.5.1.3 Absolute posioning in an-clockwise direcon 115

7.5.1.4 Relave posioning 115

7.5.1.5 Connuous posioning 116

7.5.1.6 Posioning with nal velocity 116

7.5.2 Source of hardware limit switch 117

7.5.3 External torque limitaon 118

7.5.4 Posioning to torque limit 119

7.5.5 Touch probe posioning 120

7.5.6 Source of reference switch (touch probe) 122

7.5.7 Execung and interrupng posioning 122

7.5.8 Flying homing 123

7.5.9 Connecng the speed override 124

7.6 Diagnoscs 124

8Congure posion control 125

8.1 Basic seng 126

8.1.1 Following error detecon and in-posion detecon 127

8.1.2 Interpolaon 128

8.2 Operang mode "CiA 402 cyclic sync posion mode (csp)" 130

8.2.1 Default mapping 130

8.2.2 Signal ow 131

8.2.3 Control commands and status informaon 133

8.3 Process input data (CiA 402 objects) 133

8.4 Process output data (CiA 402 objects) 134

8.5 Monitoring the posion error 134

8.6 Posion detecon with touch probe (TP) 135

8.6.1 Default mapping 135

8.6.2 General mode of operaon 136

8.6.3 Filtering of the touch probe signal 136

8.6.4 Compensaon of runme delays 137

8.6.5 Touch probe control word 138

8.6.6 Touch probe status word 139

8.6.7 Extension for the digital inputs DI3 and DI4 140

8.6.8 Detected me stamp and posions 140

8.7 Setpoint diagnoscs 141

Contents

5

9Congure speed control 142

9.1 Basic seng 142

9.2 Operang mode "CiA 402 velocity mode (vl)" 143

9.2.1 Default mapping 143

9.2.2 Signal ow (servo control) 144

9.2.3 Signal ow (V/f characterisc control) 146

9.2.4 Setpoint factor 148

9.2.5 Dimension factor 148

9.3 Operang mode "CiA 402 cyclic sync velocity mode (csv)" 149

9.3.1 Default mapping 149

9.3.2 Signal ow (servo control) 150

9.3.3 Signal ow (V/f characterisc control) 152

9.3.4 Control commands and status informaon 154

9.4 Process input data (CiA 402 objects) 154

9.5 Process output data (CiA 402 objects) 155

9.6 Monitoring the speed deviaon 155

10 Conguring the torque control 156

10.1 Basic seng 157

10.1.1 Torque limits 158

10.1.2 Speed limitaon 159

10.2 Operang mode "CiA 402 cyclic sync torque mode (cst)" 160

10.2.1 Default mapping 160

10.2.2 Signal ow 161

10.2.3 Control commands and status informaon 163

10.3 Process input data (CiA 402 objects) 163

10.4 Process output data (CiA 402 objects) 163

10.5 Setpoint diagnoscs 163

Contents

6

11 Conguring the feedback system 164

11.1 Congure feedback system for motor control 165

11.1.1 General sengs 166

11.1.2 Resolver sengs 168

11.1.2.1 Resolver error compensaon 169

11.1.3 Encoder sengs 172

11.1.3.1 SinCos encoder 172

11.1.3.2 SinCos absolute value encoder with HIPERFACE® protocol 173

11.1.3.3 SSI encoder 175

11.1.3.4 One cable technology (OCT) via HIPERFACE DSL® 178

11.1.3.5 Evaluaon of the signal quality 179

11.1.4 Detecon of changed sengs of the feedback system 180

11.1.5 Diagnoscs 180

11.2 Second feedback system for the techology applicaon 181

11.2.1 General sengs 181

11.2.2 Resolver sengs 182

11.2.2.1 Resolver error compensaon 184

11.2.3 Encoder sengs 187

11.2.3.1 SinCos encoder 187

11.2.3.2 SinCos absolute value encoder with HIPERFACE® protocol 188

11.2.3.3 SSI encoder 190

11.2.3.4 Evaluaon of the signal quality 193

11.2.4 Detecon of changed sengs of the feedback system 194

11.2.5 Diagnoscs 194

11.3 Encoder: Evaluaon of safely speed and posion 195

11.4 Synchronous motor: Pole posion idencaon (PPI) 196

11.4.1 Monitoring the pole posion idencaon 197

11.4.2 Pole posion idencaon (PPI) 360° 198

11.4.3 Pole posion idencaon (PPI) with minimum movement 203

11.4.4 Pole posion idencaon (PPI) without movement 206

11.5 Cable check 209

Contents

7

12 Conguring the motor control 213

12.1 Servo control for synchronous motor (SC-PSM) 214

12.1.1 Required commissioning steps 214

12.2 Servo control for asynchronous motor (SC-ASM) 215

12.2.1 Required commissioning steps 215

12.3 Sensorless control for synchronous motor (SL-PSM) 215

12.3.1 Required commissioning steps 215

12.4 V/f characterisc control for asynchronous motor (VFC open loop) 216

12.4.1 Required commissioning steps 216

12.4.2 Basic seng 217

12.4.3 Dene V/f characterisc shape 218

12.4.3.1 Linear V/f characterisc 218

12.4.3.2 Square-law V/f characterisc 218

12.4.3.3 User-denable V/f characterisc 219

12.4.4 Acvate voltage vector control (Imin controller) 219

12.4.5 Set voltage boost 221

12.4.6 Set load adjustment 222

12.4.7 Set slip compensaon 222

12.4.8 Set oscillaon damping 223

12.4.9 Opmising the stalling behaviour 224

12.4.10 Flying restart circuit 225

12.5 Parameterisable motor funcons 228

12.5.1 DC braking 228

12.5.2 Short-circuit braking 229

12.5.3 Holding brake control 230

12.5.3.1 Basic seng 231

12.5.3.2 Brake holding load 233

12.5.3.3 Torque feedforward control 233

12.5.3.4 Manual brake control 234

12.5.3.5 Reducon of brake supply voltage 234

12.6 Opons for opmizing the control loops 235

12.6.1 Automac motor idencaon (energized) 235

12.6.2 Tuning of the motor and the speed controller 236

12.6.3 Inverter characterisc 238

12.6.3.1 Compensang for inverter inuence 239

12.6.3.2 Extended sengs for idencaon 240

12.6.3.3 Load standard inverter characterisc 241

12.6.4 Motor equivalent circuit diagram data 241

12.6.5 Motor control sengs 243

12.6.5.1 Speed controller 243

12.6.5.2 Current controller 246

12.6.5.3 ASM eld controller 249

12.6.5.4 ASM eld weakening controller 250

12.6.5.5 ASM eld weakening controller (extended) 250

12.6.5.6 PSM eld weakening controller 251

12.6.5.7 Imax controller 252

12.6.5.8 Flying restart controller 252

12.6.5.9 Posion controller 253

Contents

8

12.7 Fine adjustment of the motor model 254

12.7.1 Correcon of the stator leakage inductance (Lss)... 255

12.7.2 Synchronous motor (SM): Compensate temperature and current inuences 260

12.7.3 Asynchronous motor (ASM): Idenfying Lh saturaon characterisc 261

12.7.4 Esmate opmum magnesing current 263

12.8 Parameterise lter elements in the setpoint path 264

12.8.1 Jerk limitaon 264

12.8.2 Notch lter (band-stop lter) 265

12.9 Motor protecon 268

12.9.1 Motor overload monitoring (i²xt) 268

12.9.1.1 Parameters for the thermal model 270

12.9.1.2 Speed-dependent evaluaon of the motor current 272

12.9.1.3 UL 508-compliant motor overload monitoring 275

12.9.2 Motor temperature monitoring 276

12.9.2.1 Individual characterisc for motor temperature sensor 278

12.9.3 Overcurrent monitoring 278

12.9.4 Motor phase failure detecon 279

12.9.5 Motor speed monitoring 280

12.10 Frequency and speed limitaons 281

12.11 Tesng the motor control 282

12.11.1 General sengs for test modes 282

12.11.2 Manual "tension/frequency" test mode 284

12.11.3 Manual "current/frequency" test mode 285

12.11.4 Manual "current pulse" test mode 286

13 I/O extensions and control connecons 288

13.1 Congure digital inputs 288

13.2 Congure analog inputs 291

13.2.1 Analog input 1 291

13.3 Congure digital outputs 293

13.3.1 Digital output 1 293

13.3.2 Digital output 2 294

13.3.3 Digital output 3 294

13.3.4 Digital output 4 294

13.3.5 Digital output 5 294

13.3.6 Digital output 6 294

14 Congure engineering port 295

14.1 Basic seng 296

14.2 NTP server addresses 298

14.3 Diagnoscs 298

Contents

9

15 Conguring the network 299

15.1 CiA 402 device prole 300

15.1.1 Supported operang modes 300

15.1.2 Basic seng 301

15.1.3 Process input data 302

15.1.4 Process output data 302

15.1.5 Commands for device state control 303

15.1.5.1 Switch on 305

15.1.5.2 Enable operaon 306

15.1.5.3 Acvate quick stop 307

15.1.5.4 Pulse inhibit 308

15.1.5.5 Reset fault 309

15.1.6 Device states 310

15.1.6.1 Not ready to switch on 312

15.1.6.2 Switch-on inhibited 313

15.1.6.3 Ready to switch on 314

15.1.6.4 Switched on 315

15.1.6.5 Operaon enabled 316

15.1.6.6 Quick stop acve 317

15.1.6.7 Fault reacon acve 318

15.1.6.8 Trouble 319

15.2 onboard EtherCAT 320

15.2.1 Commissioning 321

15.2.2 Basic seng and opons 322

15.2.3 Process data transfer 323

15.2.3.1 Process output data 324

15.2.3.2 Process input data 324

15.2.4 Monitoring 325

15.2.5 Diagnoscs 326

15.2.5.1 LED status displays 326

15.2.5.2 Informaon on the network 326

15.2.5.3 Device idencaon 328

Contents

10

15.3 EtherCAT 330

15.3.1 Commissioning 331

15.3.2 Basic seng and opons 332

15.3.2.1 Synchronisaon with "distributed clocks" (DC) 332

15.3.2.2 Parameterising addional funcons 333

15.3.3 Process data transfer 338

15.3.3.1 Standard mapping 338

15.3.3.2 Dynamic (free) conguraon 339

15.3.3.3 Further communicaon objects 339

15.3.3.4 Expert sengs 339

15.3.4 Parameter data transfer 340

15.3.5 Monitoring 340

15.3.6 Diagnoscs 341

15.3.6.1 LED status display 341

15.3.6.2 Informaon on the network 341

15.3.6.3 EtherCAT master diagnoscs 343

15.3.6.4 Error history buer 352

15.3.6.5 Device idencaon 352

15.3.7 EoE communicaon 353

15.4 PROFINET 354

15.4.1 Commissioning 356

15.4.1.1 Sengs in the »EASY Starter« 356

15.4.1.2 Restarng or stopping the communicaon 357

15.4.1.3 Sengs in the Siemens »TIA Portal« 358

15.4.1.4 Device descripon le 358

15.4.1.5 Establishing a connecon to the »EASY Starter« via PROFINET 359

15.4.2 Basic seng and opons 359

15.4.2.1 Staon name and IP conguraon 359

15.4.2.2 Suppress diagnosc messages to the IO controller 361

15.4.3 Process data transfer 361

15.4.4 Parameter data transfer 362

15.4.5 Monitoring 363

15.4.6 Diagnoscs 364

15.4.6.1 LED status display 364

15.4.6.2 Informaon on the network 364

15.4.7 PROFIsafe 366

15.4.8 PROFIenergy 367

15.4.8.1 Supported commands 367

15.4.8.2 Supported measured values 367

Contents

11

16 Device funcons 368

16.1 Opcal device idencaon 368

16.2 Reset parameters to default 369

16.3 Saving/loading the parameter sengs 370

16.4 Enabling the device 372

16.5 Restart device 372

16.6 Start/stop applicaon 373

16.7 Restarng Extended Safety 373

16.8 Export logbook 374

16.9 Delete logbook les 374

16.10 Acvate loaded applicaon 375

16.11 Uploading the applicaon 375

16.12 Inverter control word 376

16.13 Access protecon 376

16.13.1 Brand protecon 376

16.14 Switching frequency changeover 377

16.15 Device overload monitoring (ixt) 378

16.16 Heatsink temperature monitoring 379

16.17 Update device rmware 379

16.17.1 Firmware download with »EASY Starter (rmware loader)« 379

16.17.1.1 Download via Ethernet connecon 379

17 Addional funcons 380

17.1 Brake energy management 380

17.1.1 Use of a brake resistor 380

17.2 Manual jog parameters 382

17.3 Mains failure control 383

17.4 Oscilloscope funcon 384

Contents

12

18 Safety funcons 393

18.1 General informaon and basics 394

18.1.1 Safety address 394

18.1.2 Stop funcons 394

18.1.3 Priorisaon 395

18.1.4 Restart 395

18.2 Safe torque o (STO) 396

18.3 Safe stop emergency (SSE) 398

18.4 Safe stop 1 (SS1) 399

18.5 Safe stop 2 (SS2) 402

18.6 Ramp monitoring 404

18.7 Safe operang stop (SOS) 406

18.8 Safe maximum speed (SMS) 408

18.9 Safely-limited speed (SLS) 409

18.10 Safe speed monitor (SSM) 416

18.11 Safely-limited increment (SLI) 417

18.12 Safe direcon (SDI) 419

18.13 Safely-limited posion (SLP) 422

18.14 Posion-dependent safe speed (PDSS) 425

18.15 Safe homing (SHom) 428

18.15.1 Mini-homing 432

18.15.2 Slip compensaon 433

18.16 Safe cam (SCA) 435

18.17 Operaon mode selector (OMS) 437

18.18 Repair mode selector (RMS) 440

18.19 Enable switch (ES) 443

18.20 STO cascading (CAS) 444

18.21 Safe brake control (SBC) 445

18.22 Safe Mung (MUT) 448

18.23 Safe network interfaces 450

18.23.1 PROFIsafe connecon 451

18.23.2 FSoE connecon 453

18.24 Connecon to the applicaons 456

18.24.1 Safe inputs 456

18.24.2 Safe output 457

18.24.3 Control signals 457

18.24.4 Status signals 460

18.25 Safe parameter seng 465

18.25.1 Safety address 465

18.25.2 Parameter set informaon 465

18.26 Response mes 466

18.27 Diagnoscs 469

18.27.1 LED status display 469

18.27.1.1 LED status during parameter set transfer 470

18.27.2 Event history 471

18.27.3 Diagnosc parameters 472

Contents

13

19 Diagnoscs and fault eliminaon 473

19.1 LED status display 473

19.2 Logbook 474

19.3 Diagnosc parameters 476

19.3.1 Inverter diagnoscs 478

19.3.2 Motor diagnoscs 481

19.3.3 Network diagnoscs 482

19.3.4 I/O diagnoscs 484

19.3.4.1 Digital inputs and outputs 484

19.3.4.2 Analog inputs and outputs 485

19.3.5 Diagnoscs of the applicaon 485

19.3.6 Service life diagnoscs 486

19.3.7 Device idencaon 486

19.4 Error handling 488

19.4.1 Error types 488

19.4.1.1 Timeout for error response 488

19.4.2 Error conguraon 488

19.4.3 Error reset 489

19.5 Error codes, causes and remedies 490

19.5.1 Error code overview 490

19.5.2 Extended Safety - Parameter set plausibility errors 507

20 Technical data 510

21 Appendix 511

21.1 Parameter aribute list 511

21.2 Glossary 545

Contents

14

1 About this document

WARNING!

Read this documentaon carefully before starng any work.

▶Please observe the safety instrucons!

1.1 Document descripon

This documentaon is valid up to rmware version:

Firmware version Soware data version Date

V_1_3_7 V_1_3_7_001 2019-06-07

1.2 Further documents

For certain tasks, informaon is available in further documents.

Document Contents/topics

Planning manual Basic informaon on project planning and ordering the product

Mounng and switch-on instrucons Basic informaon on mounng and inial switch-on of the product

More informaon

For certain tasks, informaon is available in other media.

Medium Contents/topics

Engineering Tools For commissioning

AKB arcles Addional technical informaon for users in the Applicaon Knowledge Base

CAD data Download in dierent formats from the EASY Product Finder

EPLAN macros Project planning, documentaon and management of projects for EPLAN P8.

Device descripons Standardized les for network conguraon

Informaon and tools with regard to the Lenze products can be found on the

Internet:

www.Lenze.com à Downloads

About this document

Document descripon

15

1.3 Notaons and convenons

Convenons are used in this document to disnguish between dierent types of informaon.

Numeric notaon

Decimal separator Point Generally shown as a decimal point.

Example: 1 234.56

Warnings

UL Warnings UL Are used in English and French.

UR warnings UR

Text

Engineering Tools " " Soware

Example: "Engineer", "EASY Starter"

Icons

Page reference ¶Reference to another page with addional informaon.

Example: ¶ 16 = see page 16

Documentaon reference ,Reference to other documentaon with addional informaon.

Example: , EDKxxx = see documentaon EDKxxx

Layout of the safety instrucons

DANGER!

Indicates an extremely hazardous situaon. Failure to comply with this instrucon will result

in severe irreparable injury and even death.

WARNING!

Indicates an extremely hazardous situaon. Failure to comply with this instrucon may result

in severe irreparable injury and even death.

CAUTION!

Indicates a hazardous situaon. Failure to comply with this instrucon may result in slight to

medium injury.

NOTICE

Indicates a material hazard. Failure to comply with this instrucon may result in material

damage.

About this document

Notaons and convenons

16

2 Safety instrucons

Disregarding the following basic safety measures and safety informaon may lead to severe

personal injury and damage to property!

Observe all specicaons of the corresponding documentaon supplied. This is the

precondion for safe and trouble-free operaon and for obtaining the product features

specied.

Please observe the specic safety informaon in the other secons!

2.1 Basic safety instrucons

DANGER!

Danger to life due to electrical voltage!

The product's power connecons can sll be carrying voltage when the mains supply has been

switched o.

Possible consequences: Death, severe injury, or burns

▶Do not touch the power connecons immediately.

▶Take note of the corresponding warning plates on the product.

▶Check power terminals for isolaon from supply.

DANGER!

Dangerous electrical voltage

Possible consequences: Death or severe injuries from electric shock

▶Any work on the device must only be carried out in a deenergized state.

▶Aer switching o the mains voltage, observe the signs on the product.

Personnel

Only qualied and skilled personnel are allowed to work with the product. IEC 60364 and/or

CENELEC HD 384 dene the qualicaons of these persons as follows:

•They are familiar with the installaon, mounng, commissioning, and operaon of the

product.

•They possess the appropriate qualicaons for their tasks.

•They are familiar with all regulaons for the prevenon of accidents, direcves, and laws

applicable at the locaon and are able to apply them.

Process engineering

The procedural notes and circuit details described are only proposals. It is up to the user to

check whether they can be adapted to the parcular applicaons. Lenze does not take any

responsibility for the suitability of the procedures and circuit proposals described.

Device protecon

•The maximum test voltage for insulaon tests between a control potenal of 24 V and PE

must not exceed 110 V DC (EN 61800−5−1).

Safety instrucons

Basic safety instrucons

17

2.2 Applicaon as directed

•The product serves as a component for the control of three-phase AC motors and servo

motors.

•The product must only be actuated with motors that are suitable for the operaon with

inverters.

•The product is not a household appliance, but is only designed as electrical equipment for

commercial or professional use in terms of EN 61000−3−2.

•The product is exclusively suitable for installaon in control cabinets or similarly closed

operang areas.

•The product must only be operated under the operang condions prescribed in this

documentaon.

•The product meets the protecon requirements of 2014/35/EU: Low-Voltage Direcve.

•The product is not a machine in terms of 2006/42/EC: Machinery Direcve. With the

excepon of all funconal safety funcons.

•Commissioning or starng the operaon as directed of a machine with the product is not

permied unl it has been ensured that the machine meets the regulaons of the EC

Direcve 2006/42/EC: Machinery Direcve; observe EN 60204−1.

•Commissioning or starng operaon as directed is only permissible if the EMC Direcve

2014/30/EU is complied with.

•As the product may cause EMC interferences in residenal areas, the operator is

responsible for taking interference suppression measures.

2.3 Handling

•Connect/disconnect all pluggable terminals only in de-energized condion.

•Only remove the product from the installaon in the de-energized state.

Safety instrucons

Applicaon as directed

18

2.4 Residual hazards

Product

Observe the warning labels on the product!

DANGER!

Danger to life due to electrical voltage!

The product's power connecons can sll be carrying voltage when the mains supply has been

switched o.

Possible consequences: Death, severe injury, or burns

▶Do not touch the power connecons immediately.

▶Take note of the corresponding warning plates on the product.

▶Check power terminals for isolaon from supply.

Electrostac sensive devices:

Before working on the product, the sta must ensure to be free of electrostac charge!

WARNING!

Dangerous electrical voltage

Device error causes an overvoltage in the system.

▶For a voltage supply with DC 24 V (± 20 %), use only a safely separated power supply unit

according to the valid SELV/PELV requirements.

Motor protecon

With some sengs of the inverter, the connected motor can be overheated.

•E. g. by longer operaon of self-venlated motors at low speed.

•E. g. by longer operaon of DC-injecon braking.

Dangerous electrical voltage:

Before working on the product, make sure there is no voltage applied to the power terminals!

Aer mains disconnecon, the power terminals will sll carry the hazardous electrical voltage for the me given next to the

symbol!

High leakage current:

Carry out xed installaon and PE connecon in compliance with:

EN 61800−5−1 / EN 60204−1

Protecon of the machine/system

Drives can reach dangerous overspeeds.

•E. g. by seng high output frequencies in connecon with motors and machines not

suitable for this purpose.

•The inverters do not provide protecon against such operang condions. For this

purpose, use addional components.

Switch contactors in the motor cable only if the controller is inhibited.

•Switching while the inverter is enabled is only permissible if no monitoring funcons are

acvated.

Hot surface:

Use personal protecve equipment or wait unl the device has cooled down!

Motor

If there is a short circuit of two power transistors, a residual movement of up to 180°/number

of pole pairs can occur at the motor! (e. g. 4-pole motor: residual movement max. 180°/2 =

90°).

Safety instrucons

Residual hazards

19

NOTICE

High input voltage at the device.

Destrucon of the device.

▶Observe maximum permissible input voltage.

▶Fuse device at the input against too high input voltage.

NOTICE

Short circuit at the device due to electrostac discharge.

Destrucon of the device.

▶The personnel must be free of electrostac charge prior to working on the device.

Degree of protecon - protecon of persons and device protecon

•Informaon applies to the mounted and ready-for-use state.

•Informaon does not apply to the wire range of the terminals.

-Terminals that are not wired have low protecon against physical contact.

-Terminals for large cable cross-secons have lower classes of protecon, e. g. from

15 kW IP10 only.

Safety instrucons

Residual hazards

20

Page is loading ...

Lenze TA i900 Owner's manual

This manual is also suitable for

Lenze TA i900 Owner's manual

Related papers

Other documents