ALIBI ALI-TS7012V Quick Installation Manual

Brand: ALIBI

Model: ALI-TS7012V

Category: Security cameras

Type: Quick Installation Manual

www.observint.com

ALI-TS7012V_CQ

170224

— RS-485 address: 0

— Baud Rate: 2400

— RS-485 termination resistor: O

Using the tables below, set the switches in accordance with the following:

• The address of each device (camera) on the RS-485 network must be dierent.

• The baud rate must be the same for each device on the RS-485 network.

• The DIP switches 1 - 9, used for setting the address, baud rate, and protocol of the RS-485 network,

function logically in this way: ON=1 and OFF=0.

• The camera is self-adaptive to the Pelco-P, Pelco-D and Private-Code protocols. You don’t have to set

the DIP switches for these RS-485 control protocol.

• DIP switch 10 provides RS-485 end-of-line termination and cannot be set using the DVR interface. If

used, it must be set by opening the camera enclosure and manually setting the switch to ON.

To set the DIP switches manually, do the following:

1. Remove the lower dome cover from the camera by extracting the three screws.

Dome screws (3)

Dome

Remove lower dome

2. Locate the DIP switches inside the housing.

DIP switches

a. For DIP switches 1 .. 10 (SW1 .. SW10), use SW1 .. SW5 to set the RS-485 network address

according to the table below.

Camera address SW 1 SW 2 SW 3 SW 4 SW 5

0 OFF OFF OFF OFF OFF

1 ON OFF OFF OFF OFF

2 OFF ON OFF OFF OFF

3 ON ON OFF OFF OFF

4 OFF OFF ON OFF OFF

: : : : : :

OFF OFF ON ON ON

29 ON OFF ON ON ON

30 OFF ON ON ON ON

31 ON ON ON ON ON

ALI-TS7012V 2.0MP 23x Zoom

HD-TVI Outdoor PTZ Camera

Quick Installation Guide

The ALIBI™ ALI-TS7012V HD-TVI outdoor PTZ camera enables you to pan, tilt and zoom in on suspicious

activity and capture high denition video of wide areas such as parking lots, shopping malls and sports

facilities. The camera features:

• 2.0 MP CMOS image sensor

• On-screen displays (OSD) for conguration and programming

• 1080p HD-TVI and CVBS video output

• 23X optical zoom, 16X digital zoom

• Privacy Masking, 3D DNR, D WDR, EIS, true Day&Night

• 3D intelligent positioning

• 24 Vac power supply included

• Seven mounting bracket options (see Specications section)

For more information about this camera, including use of the On-screen displays (OSD), lightening

protection, RS-485 bus design and general warnings and cautions, refer to the ALI-TS7012V 2.0MP

HD-TVI 23x Zoom Outdoor PTZ Camera User Manual available from your vendor.

What’s in the box

This product includes:

• 24 Vac power supply

• Security wrench

• Gloves

What you need

• Tools and additional fasteners (may be required) for mounting the camera and mounting bracket

• Video and power extension cable

• HD-TVI or CVBS video setup monitor (optional)

• HD-TVI compatible (Alibi) security video recorder

Before you start, check the package contents and make sure that the device in the package is in good

condition and all the assembly parts are included.

Step 1. Set the DIP switches

DIP switches, located in the housing are used to setup the RS-485 network address (switches 1 - 5), baud

rate (switches 6 - 7), protocol (switches 8 - 9) and TVI mode (switch 10). These switches can also be setup

manually or through the DVR PTZ interface. Two additional switches are provided for RS-485 network

termination. The default DIP switch settings congure the camera for:

2 www.observint.com

b. Set switches 6 and 7 to match the RS-485 network baud rate according to the table below.

Baud rate SW 6 SW 7

2400 OFF OFF

4800 ON OFF

9600 OFF ON

19200 ON ON

c. Set switches SW8 and SW9 for the preferred RS-485 network protocol according to the table

below.

Protocol SW 8 SW 9

Protocol self-adaptive OFF OFF

Pelco-D OFF ON

d. Switch 10 congures the TVI mode.

TVI Mode SW 10

V1.0 ON

V2.0 OFF

e. Termination switches 1 and 2 provide RS-485 end of line termination. Refer to the ALI-

TS7012V 2.0MP HD-TVI 23x Zoom Outdoor PTZ Camera User Manual available from

your vendor for guidance about when these switches should be ON.

Termination SW 1 SW 2

Termination on ON ON

Termination o OFF OFF

3. Reattach the lower dome cover.

Step 2. Camera wall mount installation

The camera can be wall mounted to any indoor or outdoor solid wall using the appropriate bracket. Bracket

options are shown in the ALI-TS7012V 2.0MP HD-TVI 23x Zoom Outdoor PTZ Camera User Manual

available from your vendor.

NOTE

• The wall must be thick enough to mount the expansion screws.

• The wall must be strong enough to withstand more than 4 times the weight of the dome and its accessories.

1. Prepare the mounting surface for the camera.

a. Obtain the best fasteners for attaching the camera wall mount bracket to the mounting

surface. The fasteners must t the wall mount bracket.

b. Position the wall mount bracket in the location where you want to install it, then use it as a

guide to mark the location of the screw holes.

Screws (4)

Set screw (2)

Wall mount installation

c. Drill four screw holes according to the screw holes on the wall mount.

d. Drill a 1-1/4” hole in the mounting surface between the mounting screws appropriate for the

camera drop and interface cables.

2. Secure the camera onto the wall mount bracket as shown below:

a. Clip the camera safety cable to the loop on the mounting bracket.

b. Route the camera drop cables through the wall mount bracket.

c. Rotate the connector of the camera housing onto the wall mount bracket.

d. Tighten the set screws with the hex wrench (supplied) to hold the two units together.

Drop cable

Loop for

safety

cable

Set screw (2)

Secure the camera to the bracket

3. Route the camera drop cables through the hole for them drilled in the mounting surface.

4. Using four fasteners, secure the camera to the mounting surface.

Screw (4)

5. Remove the protective plastic lm from the lower dome.

Step 3. Connecting the cables

Before you start, remove power from the power supply cables before connect them to the camera power

cables.

The cable interfaces of camera is shown below. Two video outputs are provided: one using HD-TVI

technology that must connect to an HD-TVI compatible device, such as a Hybrid DVR, and a CVBS (NTSC)

video output that can connect to any NTSC compatible device. The RS-485 interface, power and ground,

and alarm in/out cables are distinguished by dierent colors. Please refer to the labels on the camera drop

cables and the gure below for identication.

www.observint.com

24 Vac

Ground

24 Vac

RS-485 –

RS-485 +

Alarm connections*

HD-TVI Video output

CVBS Video output

Camera drop cable

*Alarm Connections coding: Alarm connections are color coded. These wires are identied on the

Alarm Connections cable tag.

Connect the drop cable to supporting devices:

1. Route extension cables for ground, power, video (HD-TVI and CVBS), alarms and RSS-485 between

the devices to be connected and the camera as needed.

2. Connect the camera ground cable to an earth ground. Follow local electrical codes for specic

requirements.

3. Connect the two camera alarm input drop cables to normally open (NO) or normally closed (NC)

alarm sensors, if needed.

4. Connect the camera alarm output drop cables to an alarm reporting device. See the Specications

section for interface requirements and the diagram below.

Camera

Relay

output

Camera

Relay

output

The alarm provides the relay output (no voltage), and the external power supply is required when it

connects to the alarm device. With a DC power supply (left diagram), the input voltage must be no

more than 12 Vdc, 30 mA. For AC power supply (right diagram), the external relay must be used to

prevent damages to the camera and avoid risk of electric shock.

5. Connect the camera HD-TVI video drop cable to an HD-TVI compatible ALIBI video recorder.

6. Connect the CVBS video drop cable to an NTSC video compatible device, if needed.

7. Connect the RS-485 drop cables to an RS-485 network if needed. Refer to the ALI-TS7012V 2.0MP

HD-TVI 23x Zoom Outdoor PTZ Camera User Manual available from your vendor.

8. Connect the 24 Vac camera drop cable to the 24 Vac power supply provided.

9. Apply power to the camera. When the camera powers on, an information display appears in the

video from the camera (see below). (NOTE: The image below shows only the information displayed.

A video image stream from the camera will appear in the background.)

Important information about the camera settings is shown in the system information display. See below.

System Information Description

SN The serial number of the camera.

ADDRESS The default communication address of the camera.

System Information Description

COM FORMAT

The communication settings of the RS-485 interface: baud rate (4 digits), data bit (1 digit) and

number of stop bits (1 digit).

PROTOCOL Protocol conguration for communicating with other devices.

FIRMWARE The version of the rmware.

HARDWARE The version of the hardware.

BUILD DATE The date when the software was compiled.

TILT SUCCESS The tilt function test was successful.

PAN SUCCESS The pan function test was successful.

If the address of your camera is the same as another camera on the RS-485 network, one of them has to

change. Also, if the communication parameters (COM FORMAT) are not the same as the settings on RS-485

network, they must be congured to match. Use the features with your control keyboard or recorder to

congure these parameters.

Step 4. Perform basic operations

Access the camera in either of the three dierent ways included below and verify that the manual Pan and

Tilt controls and Zoom, Focus and Iris lens controls function as expected.

• Through the ALIBI recorder Live View display. In the Live View display, open the quick setting

toolbar and click the PTZ Control icon. In the PTZ Control menu, click the direction keys (p, q, t,

u) to point the camera in dierent directions. Click the Zoom +/−, Focus +/−, and Iris +/− to

verify the lens controls functions normally.

Direction keys

• Through the PTZ Control panel in the recorder. In the PTZ Control panel, click the direction

keys (p, q, t, u) to point the camera in dierent directions. Click the Zoom +/−, Focus +/−,

and Iris +/− to verify the lens controls functions normally. Specic instructions for using the PTZ

Control panel are included in the ALIBI recorder user manual.

Direction keys

• Using the PTZ control panel in the remote access interface to the recorder. Log into the

recorder remotely. Open the Live View display of the camera, and then click the direction keys (p,

q, t, u) to point the camera in dierent directions. Click the Zoom +/−, Focus +/−, and Iris

+/− to verify the lens controls functions normally.

www.observint.com

PTZ control panelPreset95 Call icon

NOTE: You can click the Preset95 call icon (see above) to open the camera OSD display. For more

information about using the OSD, refer to the ALI-TS7012V 2.0MP HD-TVI 23x Zoom Outdoor

PTZ Camera User Manual available from your vendor.

NOTE

If the camera is connected to an RS-485 network, motion and lens control functions can be controlled

with a PTZ controller. Refer to the ALI-TS7012V 2.0MP HD-TVI 23x Zoom Outdoor PTZ Camera

User Manual for information about supported PTZ Preset functions.

Step 5. Use the camera OSD to configure the camera

The on-screen display OSD menus are used to congure the video image setup, presets, patrols, time tasks,

patterns, motion, privacy zones, and alarms. Common setup tasks include conguration of the following:

• Image parameters: Image parameters include focus, zoom limit, Day/Night mode, noise reduction,

sharpness, wide dynamic range, iris, gain, shutter speed, exposure, white balance, privacy and OSD

settings.

• Presets: Presets are user-denable settings for pointing the camera at a specic eld of view. Each of

the user-denable presets can be programmed to use pan, tilt, zoom, iris, and other settings. When a

preset is called, the dome will automatically move to the dened position. You can modify, delete and

call each preset you dene.

• Tours: Tours are composed of a combination of Presets that are called automatically and sequentially.

For each preset called, a congurable dwell time, the pause time for each preset, is applied.

• Pattern: A pattern is a memorized, repeating series of pan, tilt, zoom, and preset functions that

can be recalled with a command from a controller or automatically by a congured function (alarm,

park, time task, or power-up). By default, focus and iris are in auto status when the preset is being

memorized.

• Time Task: A time task is a pre-congured action that is performed automatically at a specic date

and time. The programmable actions include: preset 1-8, pattern 1-4, patrol 1-4, pan scan, tilt scan,

panorama scan, day/night mode or none.

• Privacy zones are portions of the eld of view that are blocked (for privacy) or sensed for motion.

Refer to the ALI-TS7012V 2.0MP HD-TVI 23x Zoom Outdoor PTZ Camera User Manual available from

your vendor for a description of the camera OSD features.

Specications

Area Parameter Specication

Camera

Image sensor 1/2.8" Progressive Scan CMOS

Image resolution 1920 × 1080 max.

Resolution 30 fps (1920 × 1080)

Minimum illumination Color: 0.05 lux @ ( F1.4,AGC ON); B/W: 0.005 lux @ ( F1.4, AGC ON)

White balance Auto / Manual / ATW / Indoor / Outdoor

AGC Auto / Manual

S / N ratio ≥ 50 dB

3D-DNR Supported

Digital WDR Supported

EIS Supported

Area Parameter Specication

Camera (cont.)

Backlight Compensation Supported

Shutter time 1 ~ 1/10,000 second

Day and Night IR cut lter

Digital zoom 16X

Privacy Mask

8 privacy masks programmable; a maximum of 8 zones can be masked

simultaneously on the same video screen

Focus model Auto / Semiautomatic / Manual

Lens

Lens type Varifocal

Focus Auto

Focal length 4 ~ 92 mm, 23X

Iris DC driven

Field of View 53˚ (wide) ~ 3.1˚ (tele)

Optical zoom 23× optical, 16× digital zoom

Zoom speed ~3 second (optical wide-tele)

Angle of view 49 ~ 2.2 degree (wide-tele)

Min. Working Distance 10 ~1000 mm (wide-tele)

Aperture Range F1.4 ~ F3.5

Pan and Tilt

Pan range 360° endless

Pan speed Pan manual speed: 0.1° ~ 160° / second, pan preset speed: 160°/ second

Tilt Range 0° ~ 90° (auto ip)

Tilt Speed Tilt manual speed: 0.1° ~ 120° / second, tilt preset speed: 120° / second

Proportional zoom

Rotation speed can be adjusted automatically according to zoom

multiples

Number of preset 256

Patrol 8 patrols, up to 32 presets per patrol

Pattern 4 patterns, with a total recording time not less than 10 minutes

Power-o memory Support

Park action Preset / Patrol / Pattern / Pan Scan / Tilt Scan / Panorama scan

Scheduled Task Preset / Patrol / Pattern / Pan Scan / Tilt Scan / Panorama scan

RS-485 communication

diagnosis

Support

Input / Output

Monitor output 1 HD-TVI output, 1 CVBS output: 1.0 Vp-p / 75 Ω, NTSC composite, BNC

RS-485 interface Half-duplex mode, Self-adaptive, COAXITRON, Pelco-D protocols

UTC function COAXITRON or ALI-UTC controller

CVBS resolution 1000 TVL

Alarms 2 alarm inputs, 1 alarm output

General

Menu Language English, Chinese

Power 24 Vac, outdoor: 18 W max. (heater: 6 W), indoor: Max.12 W

Working Temperature /

Humidity

-22 °F ~ 149 °F (-30 °C ~ 65 °C) / 90% or less

Protection Level

IP66 standard (outdoor dome) TVS 4,000 V lightning protection, surge

protection, voltage transient protection

Impact protection IEC60068-275Eh, 20J; EN50102, up to IK10

Mounting Use with bracket. See Mounting Options below.

Dimension Φ7.28” × 12.99” (Φ185 × 330 mm) (outdoor)

Weight (approx.) 8.81 Ib (4 Kg)

Mounting Options

Ceiling Mount Bracket: ALI-PTZCL;

Short Arm Wall Bracket 4” PTZ: ALI-PTZWBS;

Wall Mount: ALI-PTZWB;

Wall Mount with Junction Box: ALI-PTZWBJ;

Pole Mount PTZ Bracket: ALI-PTZPM;

Corner Mount PTZ Bracket: ALI-PTZCM

ALIBI ALI-TS7012V Quick Installation Manual

Brand: ALIBI

Model: ALI-TS7012V

Category: Security cameras

Type: Quick Installation Manual

Download PDF

report

ALIBI ALI-TS7012V Quick Installation Manual

ALIBI ALI-TS7012V Quick Installation Manual

Related papers

Other documents