Page is loading ...
GE
Lighting
imagination at work
(BL Series - Pendant Mount Option)
Lumination
TM
LED Luminaires
Installation Guide
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING/AVERTISSEMENT
RISK OF ELECTRIC SHOCK
• Turn power off before inspection, installation or removal.
• Properly ground electrical enclosure.
RISK OF FIRE
• Follow all NEC and local codes.
• Use only UL approved wire for input/output connections.
Minimum size 14 AWG, rated minimum 300V.
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l’alimentation avant d’’inspecter, installer ou déplacer le luminaire.
• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation électrique.
RISQUES D’INCENDIE
• Respectez tous les codes NEC et codes locaux.
• N’utilisez que des ls approuvés par UL pour les entrées/sorties de
connexion. Taille minimum 14 AWG.
Save These Instructions
Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
Prepare Electrical Wiring Important
Required Components Based on Safety Standard
• Intended for new installlations only. Not meant to convert an
existing BL Series recessed luminaire already mounted in the
ceiling into a surface mount pendant.
• Only to be used with BL Series luminaire purchased separately,
which includes BL Series Lumination LED Luminaires
Installation Guide instructions.
• UL Listed conduit connections and ttings per NEC/CEC for
nominal conduit trade size 1/2”.
• UL Listed twist-on wire connectors.
• Use min. 600V 75°C supply conductor.
• Follow local building codes and safety regulations.
Electrical Requirements
The LED luminaire must be connected to the mains
supply according to its ratings on the luminaire
product label.
Grounding Instructions
The grounding and bonding of the overall system
shall be done in accordance to local electric code
of the country where the luminaire is installed.
Components Supplied
Part Number Description Quantity
BRA-00096-01 BL Pendant Mount Bracket 2
SCW-00015-01 M4-0.7X8 PPOZI TRS Z 4
Refer the BL Series Lumination LED Luminaires Installation
Guide provided with luminaire for luminaire electrical
connections details. See wiring diagram for reference.
Ceiling Mounting Method Options
Wiring Diagram
CAUTION
Use mounting options that are appropriate for use with your mounting surface and weight of the xture.
Description:
Mount xture directly to building structural
member such as:
• Bar joists, strut, purlins, beams roof trusses, etc.
Equipment Required (not supplied):
• 1/4”-20 or M6 threaded rod
• Contact supplier for other options
Description:
Mount xture to ceiling canopies (not supplied).
Equipment Required (not supplied):
• Suspension cable
• Single-feed Canopy Kit (67654)
• Contact supplier for other options
Black
AC
White
Green/Yellow
Grey
Violet
Violet/White
Black/White
Blue/White
Yellow
Line
Neutral
Ground
1-10V(-)
1-10V(+) DALI/PROG.
DALI/PROG.
LED Driver
Remote
Switch
(Optional)
Mount to Building Structure
Mount to Ceiling Canopy
OPTION 1
OPTION 2
NOTE:
• Use appropriate connectors to make
connections in accordance to local electric
code of the country where the luminaire is
installed as described in BL Series Lumination
LED Luminaires Installation Guide instructions
provided with the luminaire.
• UL Listed conduit connections and ttings per
NEC/CEC.
• When connecting to (optional) switch, run wires
from controller or dimmer through a different
knockout than the AC input wire. Follow lighting
controller installation instructions.
3
Move brackets to desired
locations. Ensure brackets are
not blocking wire access holes.
4 5 6
Use provided M4 tapping screws
only. Turn each screw into
bracket at an even amount so
the bracket is push up by the
screws evenly, until it is secured.
Repeat Step 4 for the other
bracket.
Follow local building codes and
acceptable mounting options.
When using shoulder-bolt or
threaded rod, 1/4”-20 or M6 is
recommended for mounting
into the ceiling structure. Use
nut above and below bracket to
prevent xture movement.
Brackets Installation
1
Carefully unpack unit from its
packaging. Properly inspect for
defects before installing. Wear
work gloves to prevent dirt and
oil from being transferred to the
luminaire.
2
Slide brackets into the top
grooves of the xture as shown.
Use one bracket on each end of
the xture.
IND124-072514
GE Lighting • 1-888-MY-GE-LED (1-888-69-43-533) • www.gelighting.com
GE Lighting Solutions, LLC is a subsidiary of the General Electric Company. The GE brand, logo, and Lumination are trademarks of the General Electric Company.
© 2014 GE Lighting Solutions, LLC. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.
/
