CEN-TECH 93297 Assembly & Operating Instructions
- Type
- Assembly & Operating Instructions
CEN-TECH 93297 is a versatile digital caliper with a range of up to 0.904 inches or 22.95 millimeters, making it ideal for precise measurements in various applications. Its features include:
-
High Accuracy: Delivers accurate measurements with a resolution of 0.001 inches or 0.2 millimeters.
-
Dual Measuring Modes: Allows switching between inches and millimeters for convenient measurements.
-
Zero Function: Enables you to set the zero point at any position, facilitating differential measurements.
CEN-TECH 93297 is a versatile digital caliper with a range of up to 0.904 inches or 22.95 millimeters, making it ideal for precise measurements in various applications. Its features include:
-
High Accuracy: Delivers accurate measurements with a resolution of 0.001 inches or 0.2 millimeters.
-
Dual Measuring Modes: Allows switching between inches and millimeters for convenient measurements.
-
Zero Function: Enables you to set the zero point at any position, facilitating differential measurements.
SKU 93297 For technical questions please call 1-800-444-3353. Page 1
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web Site at www.harborfreight.com
Copyright
©
2005 by Harbor Freight Tools
®
. All rights reserved. No
portion of this manual or any artwork contained herein may be
reproduced in any shape or form without the express written
consent of Harbor Freight Tools.
For technical questions and
replacement parts please call 1-800-444-3353.
®
1” MINI-GAUGE DIGITAL CALIPER
Technical Specifications
Material: Precision Ground stainless steel
Inside/Outside
Measuring Capacities Maximum Range: 0 to .904” or 0 to 22.95mm
Battery: SR44SW/LR44 1.5 Volt Silver Oxide (included)
Dimensions: 3-7/8” W x 1-15/16” L x 5/8” H
LCD Display: 0-1”
Accuracy: +/- .001 or +/- 0.2mm
Max Throat: 3/4”
Anvil Diameter: .079”
Inside Jaw Length: 1/4”
Dial Readings: Inches/mms
Manual Shutoff
The Digital Caliper also has a computer port for hook up to your
computer (cord not included).
93297
ASSEMBLY & OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
SKU 93297 For technical questions please call 1-800-444-3353. Page 2
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Keep work area well lighted.
3. Store idle equipment. When not in use, the Digital Caliper must be stored
in a dry location. Always lock up products and keep out of reach of
children.
4. Use the right product for the job. There are certain applications for
which the Caliper was designed. Do not modify the Digital Caliper and do
not use the Caliper for a purpose for which it was not intended.
5. Check for damaged parts. Before using any product, any part that
appears damaged should be carefully checked to determine that it will
operate properly and perform its intended function. Check for any broken
or damaged parts and any other conditions that may affect its operation.
Replace or repair damaged or worn parts immediately.
6. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty.
7. Do not operate product if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgment or
reflexes are impaired while taking drugs. If there is any doubt, do not
operate the product.
8. Use eye protection. Always wear ANSI approved impact safety goggles.
9. Battery strength will affect performance. Use fresh batteries at all times.
Warning: The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It must
be understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
Unpacking
When unpacking your Digital Caliper, check to make sure that the product is intact
and undamaged. If any parts are missing or broken, please call
HARBOR FREIGHT TOOLS at 1-800-444-3353.
Operation
Your Digital Caliper requires no assembly. It is important that you read the entire
manual to become familiar with the product BEFORE you use the Digital Caliper.
Do not bump or shock the tool when applying it to any work piece. Rough
treatment may damage the highly sensative mechanism.
Measuring the Outside of an Object
1. Push the “On” Button (see Figure 1) to “ON”. Use the thumb control to
separate the sides of the Caliper. Slide the object you wish to measure
in-between the pins on the Caliper or between the jaws on the Caliper-see
Figure 1.
Safety Warnings and Precautions
WARNING: When using product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment.
SKU 93297 For technical questions please call 1-800-444-3353. Page 3
Operation (Cont’d)
2. The LCD readout will measure the distance between the pins or jaws as the
object is measured. Press the “Zero” button to set the readout to 0. The
LCD readout will show the measurement in either inches or mm. Press the
“Off button” to turn off when finished using.
3. To change the setting from inches to millimeters, press the ON/Inch/mm
button. Each time the button is pushed the mode will change.
Measuring the Inside of an Object
1. Set the prongs on the Caliper inside of the object being measured. Make
certain the Caliper readout is calibrated to “zero” while the prongs are
closed. Spread the prongs apart until they are touching the surface of the
object being measured. The LCD readout will show the measurement in
either inches or mm.
Replacing the Battery
1. Remove the battery cover by gently prying it off.
2. Replace the battery with the type specified on page two. Insert it into the
compartment so the positive and negative polarity match those indicated.
3. Replace the battery cover. Dispose of the old battery in accordance
with local ordinances for proper disposal.
Maintenance
1. Protect the Digital Caliper from rough use. It is susceptible to damage
from being dropped, struck with a test piece, improperly mounted or other
abuse. The precision movement is similar to a watch works, and should
be treated accordingly.
2. Protect the Caliper from exposure to water or corrosive materials. It
should be kept clean and dry. Occasional cleaning with a clean rag will
extend its life and good appearance.
3. Lock it up and store in a dry location to inhibit rust. Keep out of the reach
of children.
On/Inch/mm
Pins
Jaws
LCD readout
Figure 1
Prongs
-
1
-
2
-
3
CEN-TECH 93297 Assembly & Operating Instructions
- Type
- Assembly & Operating Instructions
CEN-TECH 93297 is a versatile digital caliper with a range of up to 0.904 inches or 22.95 millimeters, making it ideal for precise measurements in various applications. Its features include:
-
High Accuracy: Delivers accurate measurements with a resolution of 0.001 inches or 0.2 millimeters.
-
Dual Measuring Modes: Allows switching between inches and millimeters for convenient measurements.
-
Zero Function: Enables you to set the zero point at any position, facilitating differential measurements.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
CEN-TECH 47257 Operating Instructions Manual
-
-
-
-
-
-
-
-
Other documents
-
LittleMachineShop 2983 User manual
-
Pittsburgh 61585 Owner's manual
-
Harbor Freight Tools 6 In. Fractional Dial Caliper User manual
-
-
-
-
U.S. General 15 PIECE SLIDE HAMMER SET Assembly and Operating Instructions
-
CHICAGO 92474 Assembly And Operating Instructions Manual
-
Pittsburgh Item 63586-UPC 193175345486 Owner's manual
-
Pittsburgh Item 63731-UPC 193175332530 Owner's manual
