Rugged Ridge 15201.09 Installation guide

Brand
Rugged Ridge
Model
15201.09
Category
Car kits
Type
Installation guide

This manual is also suitable for

Page 1
Rev (3) 11/20/09
Important: Please read instructions completely before installing wheel spacer - adaptor.
Jeep®
Wheel Spacers and Adaptors (CJ, YJ, TJ, JK)
Part numbers:
15201.02 - (Spacer 1.25") Designed for 1987-2006 Jeep® vehicles with 5 x 4.5 bolt pattern
15201.08 - (Spacer 1.50") Designed for 1987-2006 Jeep® vehicles with 5 x 4.5 bolt pattern
15201.03 - (Spacer 1.25") Designed for 1945-1986 Jeep® vehicles with 5 x 5.5 bolt pattern
15201.09 - (Spacer 1.50") Designed for 1945-1986 Jeep® vehicles with 5 x 5.5 bolt pattern
15201.05 - (Spacer 1.50") Designed for 2007 - UP Jeep® vehicles with 5" x 5" bolt pattern
15201.06 - (Adaptor 1.37") Designed for 2007 - UP Jeep® vehicles with 5" lug spacing to 4.5"
15201.07 - (Adaptor 1.37") Designed for 2007 - UP Jeep® vehicles with 5" lug spacing to 5.5"
15201.04 - (Adaptor 1.25") Designed for 1987-2006 Jeep® vehicles with lug 4.5" spacing to 5.5"
Kit content: (2) T6 Aluminum spacer or adaptor
(10) Grade 8 Wheel Stud (pre-pressed)
(10) Lug Nuts
(1) Remove tire using the proper procedures called out in the Jeep® service manual
(2) Remove any retainer clips from the mating surface of drums and or rotors.
WARNING: It is very important that all retainer clips be removed before installing spacers or adaptors
Surface of rotor or drum must be cleaned. All mud, dirt, rust and or scaling must be removed
before spacer or adaptor can be installed. Failure to follow instructions may not allow spacer
or adaptor to be properly tightened.
(3) Clean wheel studs with wire brush. Apply a quality thread lock to axle wheel studs.
WARNING: Attach spacer - adaptor using supplied lug nuts only. Make sure axle studs clear spacer
- adaptor and allow full engagement of lug nut threads.
NEVER DOUBLE STACK wheel spacer-adaptors. you can be KILLED or SERIOUSLY HURT
if warning is ignored.
(4) Thread supplied lug nuts to axle studs with tapered end oriented to toward spacer- adaptor. Tighten
lug nuts in a crisscross pattern. Set torque to 85-100 ft-lbs. It will help to have another person holding
the brake pedal when tightening.
(5) Clean and remove any dirt, rust or scaling from mating surface of road wheel. Reinstall tire to spacer
- adaptor with factory lug nuts. Tighten to factory specifications.
15201.02 - (Spacer 1.25") Designed for 1987-2006 Jeep® vehicles with 5 x 4.5 bolt pattern
Factory Lug Nut
Install to spacer
adaptor stud
Wheel Spacer - Adaptor
Supplied Lug Nut
Install to axle stud
  • Page 1 1

Rugged Ridge 15201.09 Installation guide

Brand
Rugged Ridge
Model
15201.09
Category
Car kits
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents