Lightolier 9196 User manual

Lightolier
Brand
Lightolier
Model
9196
Category
Floodlights
Type
User manual
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FlfiURE
INSTRUCTION SHEET NO.
“his fixture is intended for installation in accordance with the National Electrical Code and local regulations.
‘o assure full compliance with local codes and regulations, check with your local electrical inspector before
nstallation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
IS:9196
Retain these instructions for maintenance reference.
0395
Page 1 of 1
T-BARLIVEEND
FOR USE WITH PROFILE, TRACK SYSTEMS ONLY
WARNING:
● TURN OFF POWER AT FUSE BOX BEFORE INSTALLING ELECTRICAL CONNECTOR AND TRACK.
c DO NOT USE ELECTRICAL CONNECTOR AS A CONDUIT SUPPORT. INDEPENDENT CONDUIT SUPPORTS (SUCH AS
CONDUIT STRAPS) MUST BE USED TO AllACH THE CONDUIT INSTALLATION TO THE BUILDING STRUCTURE.
● OBSERVE POLARITY; WHITE NEUTRAL WIRE MUST BE CONNECTED TO THE TERMINAL MARKED “NEUT” IN THE
ELECTRICAL CONNECTOR.
● USE 12 OR 14 GAUGE SOLID WIRE IN ELECTRICAL CONNECTOR ONLY.
NOTE: Special care must be taken when making the hole in the mounting surface to prevent the hole from being visible
when the track is mounted. The screws on the ELECTRICAL FITTING may have to be cut to conceal the mounting hole.
A. INSTALLING SURFACE FEED CONNECTOR
1.
Point the POLARITY TAB away from the BEAD on the track.
.
.—
2. Insert SURFACE FEED CONNECTOR into track. Ensure CONTACT
BLADES insert into the TRACK CONDUCTOR GAPS.
4. Tighten LOCKING SCREW.
!? **OR
ELECTRICALFITTING
B. DIRECT POWER FEED.
1.Remove BOTTOM COVER by removing SCREW (retain).
2. Remove one K,O,
-
ELECTRICALFl~lNG V’
) (ByOTHEPS) ‘
3. Attach the ELECTRICAL FITTING onto the METAL PLATE
4. Mount TRACK ASSEMBLY to T-RUNNER using CLIPS 9188 or 9189.
/
(SOLD SEPARATELY),
/ ‘+
5. Pass Supply LEADS through ELECTRICAL Fl~lNG and
*
.
secure conduit to ELECTRICAL Fl~lNG.
6. Strip and form Supply LEADS to fit into
&>*
*
SURFACE FEED CONNECTOR, Fasten Supply
LEADS to SCREW TERMINALS; NEUTRAL
(WHITE) LEAD to terminal marked “NEUT”
GROUND LEAD to TERMINAL marked “GND”,
p~~~, -OK,N~~~Ew
HOT (BLACK) LEAD to BRASS SCREW.
\
‘:.:’”’~-’--z:-z.. -,---- / . ~~;- -’::-
7, Fasten BOTTOM COVER to SURFACE FEED
\\=.-yy: \
~~~~& \c_-_—-— –/ *
CONNECTOR using SCREW.
,F=~Q ‘k’+ ‘: ‘: : –
----~–-’’’=l’ -‘ J-
‘a, ,,
/
BOTTOM COVER
‘d> ~;:fRITy
r
TRACK —
Y
/
BEAD
-\
‘~>
P
4
w 7/16”
,. . ... .... ..!.5/
g>
STRIP
/iL/
~.._—
SUPPLY
WIRE
SCREW --
TWO WIRES MAY BE ATTACHED
TO ONE SCRE’AJTERMINAL
1.1 C> I+ TC>I. I 1: 1?
@
FALL RIVER, MASSACHUSETTS, 02720
MONTREAL, QUEBEC, CANADA
d
  • Page 1 1

Lightolier 9196 User manual

Lightolier
Brand
Lightolier
Model
9196
Category
Floodlights
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents