Lightolier 9147 User manual

Brand: Lightolier

Model: 9147

Category: Floodlights

Type: User manual

Lightolier 9147 is a surface feed connector designed for use with a Profile track system. It allows for a direct power feed using surface conduit or from above the ceiling. The connector features a polarity tab to ensure proper polarity and uses 12 or 14 gauge solid wire. It also has a removable bottom cover for easy access to the screw terminals and a locking screw to secure the cover. The Lightolier 9147 is a versatile and convenient solution for providing power to track lighting systems.

READAND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE INSTRUCTION SHEET NO.

“his fixture is intended

for installation in accordance with the National Electrical Code and local regulations.

“o assure full compliance with local codes and regulations, check with your local electrical inspector before

wtallation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

IS:9147

Retain these instructions for maintenance reference.

0395

Page 1 of 1

SURFACEFEEDCONNECTOR

FORUSEWITH PROFILETRACKSYSTEM ONLY

WARNING:

● TURN OFF POWER AT FUSE BOX BEFORE INSTALLING ELECTRICAL CONNECTOR AND TRACK.

● DO NOT USE ELECTRICAL CONNECTOR AS A CONDUIT SUPPORT. INDEPENDENT CONDUIT SUPPORTS (SUCH AS

CONDUIT STRAPS) MUST BE USED TO ATTACH THE CONDUIT INSTALLATION TO THE BUILDING STRUCTURE.

. OBSERVE POLARITY; WHITE NEUTRAL WIRE MUST BE CONNECTED TO THE TERMINAL MARKED “NEUT” IN THE

ELECTRICAL CONNECTOR.

. USE 12 GA. OR 14 GA. SOLID WIRE IN ELECTRICAL CONNECTOR ONLY.

INSTALLING SURFkCE FEED CONNECTOR.

—

~/; —

/,/

1.Point the POLARITY TAB away from the BEAD ON the track.

,,,

\\\ ‘

2, Insert SURFACE FEED CONNECTOR into track. Ensure CONTACT

b<!—.~

—

BLADES insert

into the GAP of the TRACK COPPER CONDUCTOR.

3. Tighten LOCKING SCREW.

(BYOTHERS)

CONTACT BLAOE

B. DIRECT POWER FEED USING SURFACE CONDUIT.

THROUGH CE!LING FEEO

Remove BO~OM COVER by removing SCREW (retain).

2. Remove PLASTIC TAB from BOTTOM COVER.

3. Screw the ELECTRICAL FITTING into the METAL PI-ATE of the

SURFACE FEEOI

Surface Feed Connector.

4. Pass Supply LEAOS through ELECTRICAL FITTING and secure

conduit to ELECTRICAL FITTING.

5. Strip and form Supply LEADS to fit into SURFACE FEED

CONNECTOR. Fasten Supply LEADS to SCREW TERMINALS;

NEUTRAL (WHITE) LEAD to terminal marked “NEUT”. GROUND

LEAD to TERMINAL marked “GND”. HOT (BLACK) LEAD to

BRASS SCREW.

6. Fasten BOTTOM COVER to SURFACE FEED CONNECTOR using SCREW.

DIRECT POWER FEED FROM ABOVE CEILING

NEUTRAL SUPPLY

TRACK

Remove BOTTOM COVER by removing SCREW (retain).

BEAO

! WIRE (WHITEi

~ LOCKING SCREW ~

2. Remove Knock Out from METAL PLATE.

3. Secure ELECTRICAL FITTING TO MEAL PLATE using the NUT

provided.

,,———— ——

“- ~~d=.. “ —.

(c b, —-— .:

NOTE: Special care must be taken when making the

,(3T f—.— -- -—

hole in the mounting surface to prevent the hole from

(~:~p:-- ‘~~--

-F”--- ~

being visible when the track is mounted. The screws

-~’/---.-=>._-, ::$~ “–-

on the ELECTRICAL FllllNG may have to be cut to

conceal the mounting hole.

,’––-. .—.

~.–

w—--- ~—z::

Follow instruction 4, 5 and 6 above.

—HOT SUPPLYWIRE

- SUPPLYWIRE(BLACK)

- POLARllYTAB

D. POWER FEED FROM STEM KIT

GROUNO

—–- 7/16STRIP

Remove BOTTOM COVER by removing SCREW.

~;”,

SUPPLYWIRE

2. Remove KNOCK OUT from the TOP METAL PLATE.

YCH

~ — ________ --

3. Pass SUPPLY LEADS through KNOCK OUT HOLE.

/ --.-——–––-

4. Follow instructions 5 and 6 above.

‘lWO WIRES MAY BE ATTACHEO

FALL RIVER MASSACHUSETTS, 02720

l-I c> 1+ ~c>lm I 1= 1? MON::::::;EC, CANADA

Lightolier 9147 User manual

Brand: Lightolier

Model: 9147

Category: Floodlights

Type: User manual

Download PDF

report

Lightolier 9147 User manual

Lightolier 9147 User manual

Related papers

Other documents