Advantech PCI-1718 User manual

PCI-1718 Series

12-bit Multifunction Cards with

Universal PCI Bus

User Manual

PCI-1718 Series User Manual ii

Copyright

The documentation and the software included with this product are copy-

righted 2005 by Advantech Co., Ltd. All rights are reserved. Advantech

Co., Ltd. reserves the right to make improvements in the products

described in this manual at any time without notice. No part of this man-

ual may be reproduced, copied, translated or transmitted in any form or

by any means without the prior written permission of Advantech Co., Ltd.

Information provided in this manual is intended to be accurate and reli-

able. However, Advantech Co., Ltd. assumes no responsibility for its use,

nor for any infringements of the rights of third parties, which may result

from its use.

Acknowledgements

Intel and Pentium are trademarks of Intel Corporation.

Microsoft Windows and MS-DOS are registered trademarks of

Microsoft Corp.

All other product names or trademarks are properties of their respective

owners.

This Manual Covers the Following Models

• PCI-1718HDU

• PCI-1718HGU

Part No. 2003171800 1st Edition

Printed in Taiwan March 2005

iii

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its prod-

ucts will be free from defects in materials and workmanship for two years

from the date of purchase.

This warranty does not apply to any products which have been repaired or

altered by persons other than repair personnel authorized by Advantech,

or which have been subject to misuse, abuse, accident or improper instal-

lation. Advantech assumes no liability under the terms of this warranty as

a consequence of such events.

Because of Advantech’s high quality-control standards and rigorous test-

ing, most of our customers never need to use our repair service. If an

Advantech product is defective, it will be repaired or replaced at no

charge during the warranty period. For out-of-warranty repairs, you will

be billed according to the cost of replacement materials, service time and

freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For

example, CPU speed, Advantech products used, other hardware

and software used, etc.) Note anything abnormal and list any

onscreen messages you get when the problem occurs.

2. Call your dealer and describe the problem. Please have your man-

ual, product, and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return

merchandize authorization) number from your dealer. This allows

us to process your return more quickly.

4. Carefully pack the defective product, a fully-completed Repair and

Replacement Order Card and a photocopy proof of purchase date

(such as your sales receipt) in a shippable container. A product

returned without proof of the purchase date is not eligible for war-

ranty service.

5. Write the RMA number visibly on the outside of the package and

ship it prepaid to your dealer.

PCI-1718 Series User Manual iv

CE

This product has passed the CE test for environmental specifications

when shielded cables are used for external wiring. We recommend the use

of shielded cables. This kind of cable is available from Advantech. Please

contact your local supplier for ordering information.

Technical Support and Assistance

Step 1. Visit the Advantech web site at www.advantech.com/support

where you can find the latest information about the product.

Step 2. Contact your distributor, sales representative, or Advantech's cus-

tomer service center for technical support if you need additional

assistance. Please have the following information ready before

you call:

- Product name and serial number

- Description of your peripheral attachments

- Description of your software (operating system, version, appli-

cation software, etc.)

- A complete description of the problem

- The exact wording of any error messages

Packing List

Before setting up the system, check that the items listed below are

included and in good condition. If any item does not accord with the

table, please contact your dealer immediately.

• PCI-1718HDU/HGU DA&C card

• PCI-1718HDU/HGU User Manual

• Companion CD-ROM with DLL drivers

Safety Precaution - Static Electricity

Follow these simple precautions to protect yourself from harm and the

products from damage.

1. To avoid electrical shock, always disconnect the power from your

PC chassis before you work on it. Don't touch any components on

the CPU card or other cards while the PC is on.

2. Disconnect power before making any configuration changes. The

sudden rush of power as you connect a jumper or install a card may

damage sensitive electronic components.

v

Contents

Chapter 1 Introduction ..................................................... 2

1.1 Features ............................................................................. 3

1.2 Applications ..................................................................... 4

1.3 Installation Guide ............................................................. 5

Figure 1.1:Installation Flow Chart ................................. 6

1.4 Software Overview ........................................................... 7

1.5 Device Driver Programming Roadmap ............................ 8

1.6 Accessories...................................................................... 10

Chapter 2 Installation ..................................................... 12

2.1 Unpacking ....................................................................... 12

2.2 Driver Installation ........................................................... 13

Figure 2.1:Setup Screen of Automation Software ....... 14

Figure 2.2:Different Options for Driver Setup ............ 14

2.3 Hardware Installation ...................................................... 15

2.4 Device Setup & Configuration ....................................... 16

Figure 2.3:The Device Manager Dialog Box ............... 16

Figure 2.4:The Device Setting Dialog Box ................. 17

Figure 2.5:Device Name Appearing on the List of Devic-

es Box .............................................................. 17

Figure 2.6:The Test Utility Dialog Box ....................... 18

Chapter 3 Signal Connections ........................................ 20

3.1 Overview ......................................................................... 20

3.2 Switch and Jumper Settings ........................................... 20

Figure 3.1:Card Conn., Jumper & Switch Locations ... 20

3.2.1 Setting the BoardID Switch (SW1) ............................. 21

Table 3.1:Board ID Setting (SW1) .............................. 21

3.2.2 Channel Configuration, S/E or DIFF (SW2) ............... 22

Table 3.2:Summary of Switch SW2 Settings .............. 22

3.2.3 D/A Reference Voltage, int./ext. (JP11) ...................... 22

Table 3.3:Summary of Jumper JP11 Settings .............. 22

3.2.4 Internal Voltage Reference, -10 V or -5 V (JP10) ....... 23

Table 3.4:Summary of Jumper JP10 Settings .............. 23

3.2.5 Timer Clock Selection (JP8) ........................................ 24

Table 3.5:Summary of Jumper JP8 Settings ................ 24

3.2.6 Ext. trigger and Counter Gate 0 Control (JP5) ............ 25

Table 3.6:Summary of Jumper Settings ....................... 25

3.2.7 Digital Output, 20-pin or 37-pin Connector (JP1) ....... 25

Table 3.7:Summary of Jumper Settings ....................... 26

3.2.8 Setting the Time to Reset Digital Outputs ................... 27

Table 3.8:JP21 Jumper Settings ................................... 27

3.3 Signal Connections.......................................................... 28

Figure 3.2:I/O Connector Pin Assignments for the PCI-

1718 Series ....................................................... 28

3.3.1 I/O Connector Signal Description ................................ 29

PCI-1718 Series User Manual vi

Table 3.9:I/O Connector Signal Descriptions .............. 29

3.3.2 Analog Input Connections ........................................... 30

Figure 3.3:Analog Output Connections ....................... 33

3.3.3 Digital Signal Connections .......................................... 34

3.4 Field Wiring Considerations .......................................... 35

Chapter 4 Programming Guide ..................................... 38

4.1 Overview ......................................................................... 38

4.2 Programming with the Driver ......................................... 38

4.3 Register Programming..................................................... 38

4.3.1 Software Trigger and Polling ....................................... 39

4.3.2 Pacer Trigger Mode with Interrupt .............................. 41

4.3.3 Pacer Trigger Mode with Interrupt and FIFO .............. 45

4.4 Programming with LabVIEW and ActiveDAQ.............. 49

Appendix A Specifications ................................................. 52

A.1 Analog Input.................................................................... 52

A.2 Analog Output................................................................. 53

A.3 Digital Input .................................................................... 53

A.4 Digital Output.................................................................. 54

A.5 Counter/Timer ................................................................. 54

A.6 General ............................................................................ 55

Appendix B Block Diagrams ............................................. 58

Appendix C Register Structure & Format....................... 60

C.1 Overview ......................................................................... 60

C.2 I/O Port Address Map .................................................... 60

Table C.1:PCI-1718HDU/HGU Reg. Format (Part 1) 61

Table C.2:PCI-1718HDU/HGU Reg. Format (Part 2) 62

Table C.3:PCI-1718HDU/HGU Reg. Format (Part 3) 63

C.3 A/D Data and Channels — BASE+00H~01H ................ 64

Table C.4:Register for A/D Data and Channels .......... 64

C.4 Software A/D Trigger — BASE+00H ............................ 64

Table C.5:Register for Software A/D Trigger ............. 64

C.5 A/D Range Control — BASE+01H ............................... 65

Table C.6:Register for A/D Range Control ................. 65

C.6 MUX Scan Channel Control — BASE+02H.................. 67

Table C.7:Register for MUX Scan Channel Control ... 67

C.7 MUX Scan Channel Status — BASE+02H .................... 68

Table C.8:Register for MUX Scan Channel Status ..... 68

C.8 Digital I/O Registers - BASE + 03/0BH ......................... 68

Table C.9:Register for Digital Output ......................... 68

Table C.10:Register for Digital Output ...................... 69

C.9 D/A Output — BASE+04/05H ....................................... 69

Table C.11:Register for D/A Output ........................... 69

C.10 FIFO Interrupt Control — BASE+06H........................... 70

Table C.12:Register for FIFO Interrupt Control .......... 70

C.11 Clear Interrupt Request — BASE+08H.......................... 71

Table C.13:Register for Clear Interrupt Request ......... 71

C.12 A/D Status — BASE+08H.............................................. 71

Table C.14:Register for A/D Status ............................. 71

vii

C.13 A/D Control — BASE+09H ........................................... 73

Table C.15:Register for A/D Control ......................... 73

C.14 Timer/Counter Enable — BASE+0AH........................... 74

Table C.16:Register for Timer/Counter Enable ........... 74

C.15 Programmable Timer/Counter — BASE+0C~0FH ........ 74

C.16 Clear FIFO Interrupt Request — BASE+14H ................ 75

Table C.17:Register for Clear FIFO Interrupt Request 75

C.17 A/D Data and Channel from FIFO - BASE + 17/18H .... 75

Table C.18:Register for A/D Data and Channel from

FIFO ................................................................. 75

C.18 FIFO Status — BASE+19H ............................................ 76

Table C.19:Register for FIFO Status ........................... 76

C.19 FIFO Clear — BASE+19H ............................................. 76

Table C.20:Register for FIFO Clear ............................ 76

C.20 Register Programming Flow Chart ................................. 77

C.20.1 Software Trigger Mode with Polling ........................... 77

C.20.2 Pacer Trigger Mode with Interrupt .............................. 78

C.20.3 Pacer Trigger Mode with Interrupt [FIFO Used] ......... 79

Appendix D Calibration ..................................................... 82

D.1 VR Assignment .............................................................. 83

Figure D.1:PCI-1718 VR Assignment ......................... 83

D.2 A/D Calibration............................................................... 84

D.3 D/A Calibration............................................................... 85

PCI-1718 Series User Manual viii

2

CHAPTER

1

Introduction

This chapter introduces the PCI-1718

cards and their typical applications.

Sections include:

• Features

• Applications

• Installation Guide

• Software Overview

• Device Driver Programming Road-

map

• Accessories

PCI-1718 Series User Manual 2

Chapter 1 Introduction

Thank you for buying the Advantech PCI-1718HDU/HGU. PCI-

1718HDU/HGU is a PCI-Bus multifunction card for IBM PC/XT/AT or

compatible computers. It offers the five most desired measurement and

control functions:

• 12-bit A/D conversion

• D/A conversion

• Digital input

• Digital output

• Timer/counter.

A programmable-gain instrument amplifier lets you acquire different

input signals without external signal conditioning. An onboard 1 K word

FIFO buffer provides high-speed data transfer and predictable perfor-

mance under Windows. Automatic channel scanning circuitry and

onboard SRAM let you perform multiple-channel A/D conversion with

DMA and individual gains for each channel.

PCI-1718HDU/HGU is compatible* with its ISA-Bus predecessor, the

PCL-818HD/HG. This puts rich software support and a wide variety of

external signal conditioning boards at your disposal.

The following sections of this chapter will provide further information

about features of the multifunction cards, a Quick Start for installation,

together with some brief information on software and accessories for the

PCI-1718 cards.

Note*

1. PCI-1718HDU/HGU is register-level- pro-

gramming compatible with PCL-818HD/HG

2. Due to the difference between ISA and PCI

architecture, we use “interrupt + FIFO” to emu-

late the DMA function. But it makes no differ-

ence to your programming and applications.

3 Chapter 1

1.1 Features

• Register level programming compatible with PCL-818HD/HG

• 16 single-ended or 8 differential A/D inputs, switch selectable

• 12-bit A/D converter, up to 100 kHz sampling rate

• Programmable gain for each input channel

• Automatic Channel/Gain Scanning

• On-board 1 K word FIFO buffer with software selectable interrupt

• Software selectable Bipolar/Unipolar analog input ranges

• 16 digital inputs and 16 digital outputs, TTL/DTL compatible

• One 12-bit analog output channel

• Data transfers by program control and interrupt handler routine

• Universal PCI-Bus (Support 3.3V or 5V PCI-Bus signal)

• BoardID switch

PCI-1718HDU/HGU offers the following main features:

PCI-Bus Plug & Play

The PCI-1718 cards use a PCI controller to interface the card to the PCI

bus. The controller fully implements the PCI bus specification Rev 2.2.

All configurations related to the bus, such as base address and interrupt

assignment, are automatically controlled by software. No jumper or

switch is required for user configuration.

Automatic Channel/Gain Scanning

PCI-1718HDU/HGU features an automatic channel/gain scanning circuit.

This circuit, instead of your software, controls multiplexer switching dur-

ing sampling. On-board SRAM stores different gain values for each chan-

nel. This combination lets user perform multi-channel high-speed

sampling (up to 100 kHz) for each channel.

PCI-1718 Series User Manual 4

Onboard FIFO

There are 1 K samples FIFO for A/D (AI) on PCI-1718HDU/HGU. This

is an important feature for faster data transfer and more predictable per-

formance under Windows system.

Onboard Programmable Timer/Counter

PCI-1718HDU/HGU provides a programmable timer counter for generat-

ing pacer trigger for the A/D conversion. The timer/counter chip is

82C54, which includes three 16-bit counters of 10 MHz clock. One

counter is used as an event counter for counting events coming from the

input channel. The other two are cascaded together to make a 32-bit timer

for pacer trigger time base.

BoardID Switch

PCI-1718HDU/HGU has a built-in DIP switch that helps define each

card’s ID when multiple PCI-1718HDU/HGU cards have been installed

on the same PC chassis. The BoardID setting function is very useful when

building a system with multiple PCI-1718 cards. With the correct Boar-

dID settings, you can easily identify and access each card during hard-

ware configuration and software programming.

1.2 Applications

• Transducer and sensor measurements

• Waveform acquisition and analysis

• Process control and monitoring

• Vibration and transient analysis

Note: For detailed specifications of the PCI-

1718HDU/HGU, please refer to Appendix A.

5 Chapter 1

1.3 Installation Guide

Before you install your PCI-1718HDU/HGU card, please make sure you

have the following necessary components:

• PCI-1718HDU/HGU DA&C card

• PCI-1718HDU/HGU User Manual

• Driver software Advantech DLL drivers (included in the companion

CD-ROM)

• Personal computer or workstation with a PCI-bus slot (running Win-

dows 98/2000/XP)

• PCL-10120 or PCL-10137 Wiring cable (optional)

• ADAM-3920/3937, PCLD-7216/780/782/782B/785/785B/786/788/

789D/880/885/8115 Wiring board (optional)

Some other optional components are also available for enhanced opera-

tion:

• ActiveDAQ, ADAQView, LabView or other third-party software pack-

ages

After you get the necessary components and maybe some of the accesso-

ries for enhanced operation of your multifunction card, you can then

begin the installation procedure. Figure 1.1 on the next page provides a

concise flow chart to give users a broad picture of the software and hard-

ware installation procedures:

PCI-1718 Series User Manual 6

Figure 1.1: Installation Flow Chart

7 Chapter 1

1.4 Software Overview

Advantech offers a rich set of DLL drivers, third-party driver support and

application software to help fully exploit the functions of your PCI-

1718HDU/HGU card:

• Device Drivers (on the companion CD-ROM)

• LabVIEW driver

• Advantech ActiveDAQ

• Advantech ADAQView

Programming choices for DA&C cards

You may use Advantech application software such as Advantech Device

Drivers. On the other hand, advanced users can use register-level pro-

gramming, although this is not recommended due to its laborious and

time-consuming nature.

Device Drivers

Advantech Device Driver software is included on the companion CD-

ROM at no extra charge. It also comes with all Advantech DA&C cards.

Advantech’s Device Drivers features a complete I/O function library to

help boost your application performance. Advantech Device Drivers for

Windows 98/2000/XP works seamlessly with development tools such as

Visual C++, Visual Basic, Borland C++ Builder and Borland Delphi.

Register-level Programming

Register-level programming is available for experienced programmers

who find it necessary to write code directly at the level of the device reg-

ister. Since register-level programming requires much effort and time, we

recommend that you use the Advantech Device Drivers instead. How-

ever, if register-level programming is indispensable, you should refer to

the relevant information in Appendix C, Register Structure and Format,

or to the example codes included on the companion CD-ROM.

PCI-1718 Series User Manual 8

1.5 Device Driver Programming Roadmap

This section will provide you a roadmap to demonstrate how to build an

application from scratch using Advantech Device Drivers with your

favorite development tools such as Visual C++, Visual Basic, Delphi and

C++ Builder. The step-by-step instructions on how to build your own

applications using each development tool will be given in the Device

Drivers Manual. Moreover, a rich set of example source code is also

given for your reference.

Programming Tools

Programmers can develop application programs with their favorite devel-

opment tools:

• Visual C++

• Visual Basic

• Delphi

• C++ Builder

For instructions on how to begin programming works in each develop-

ment tool, Advantech offers a Tutorial Chapter in the Device Drivers

Manual for your reference. Please refer to the corresponding sections in

this chapter on the Device Drivers Manual to begin your programming

efforts. You can also look at the example source code provided for each

programming tool, since they can get you very well oriented.

The Device Drivers Manual can be found on the companion CD-ROM.

Alternatively, if you have already installed the Device Drivers on your

system, The Device Drivers Manual can be readily accessed through the

Start button:

Start\Advantech Automation\Device Manager\Device Driver's Manual

The example source code could be found under the corresponding instal-

lation folder such as the default installation path:

Program Files\Advantech\ADSAP\Examples

For information about using other function groups or other development

tools, please refer to the Creating Windows 98/2000/XP Application with

Device Drivers chapter and the Function Overview chapter on the Device

Drivers Manual.

9 Chapter 1

Programming with Device Drivers Function Library

Advantech Device Drivers offer a rich function library that can be uti-

lized in various application programs. This function library consists of

numerous APIs that support many development tools, such as Visual

C++, Visual Basic, Delphi and C++ Builder.

According to their specific functions or services, APIs can be categorized

into several function groups:

• Analog Output Function Group

• Digital Input/Output Function Group

• Counter Function Group

• Port Function Group (direct I/O)

• Event Function Group

For the usage and parameters of each function, please refer to the Func-

tion Overview chapter in the Device Drivers Manual.

Troubleshooting Device Drivers Error

Driver functions will return a status code when they are called to perform

a certain task for the application. When a function returns a code that is

not zero, it means the function has failed to perform its designated func-

tion. To troubleshoot the Device Drivers error, you can pass the error

code to DRV_GetErrorMessage function to return the error message.

Alternatively, you can refer to the Device Drivers Error Codes Appendix

in the Device Drivers Manual for a detailed listing of Error Codes, Error

IDs and Error Messages.

PCI-1718 Series User Manual 10

1.6 Accessories

Advantech offers a complete set of accessory products to support the

PCI-1718HDU/HGU card. These accessories include:

Wiring Cables

PCL-10120

The PCL-10120 cable is a 20-pin flat cable for PCI-1718HDU/HGU

cards.

PCL-10137

The PCL-10137 shielded cable is specially designed for PCI-1718HDU/

HGU cards to provide high resistance to noise. To achieve a better signal

quality, the signal wires are twisted in such a way as to form a “twisted-

pair cable”, reducing cross-talk and noise from other signal sources. Fur-

thermore, its analog and digital lines are separately sheathed and shielded

to neutralize EMI/EMC problems.

Wiring Boards

• ADAM-3920 20-pin wiring terminal for DIN-rail mounting

• ADAM-3937 37-pin D-type wiring terminal for DIN-rail mounting

• PCLD-7216 16-channel SSR I/O module carrier board

• PCLD-780 Universal screw-terminal board

• PCLD-782 16-channel opto-isolated D/I board

• PCLD-782B 24-channel opto-isolated D/I board

• PCLD-785 16-channel relay output board

• PCLD-785B 24-channel relay output board

• PCLD-786 8-channel SSR I/O module carrier board

• PCLD-788 16-channel relay multiplexer board

• PCLD-789D Amplifier and multiplexer board

• PCLD-880 Universal screw-terminal board

• PCLD-885 16-channel power relay output board

• PCLD-8115 Industrial wiring terminal with CJC circuit

2

CHAPTER

2

Installation

This chapter provides a packaged item

checklist, proper instructions for

unpacking and step-by-step procedures

for both driver and card installation..

Sections include:

• Unpacking

• Driver Installation

• Hardware Installation

• Device Setup & Configuration

PCI-1718 Series User Manual 12

Chapter 2 Installation

2.1 Unpacking

After receiving your PCI-1718HDU/HGU package, please inspect its

contents first. The package should contain the following items:

• PCI-1718HDU or PCI-1718HGU card

• Companion CD-ROM (Device Drivers included)

• User Manual

The PCI-1718 cards harbor certain electronic components vulnerable to

electrostatic discharge (ESD). ESD can easily damage the integrated cir-

cuits and certain components if preventive measures are ignored.

Before removing the card from the antistatic plastic bag, you should take

the following precautions to ward off possible ESD damage:

• Touch the metal part of your computer chassis with your hand to dis-

charge the static electricity accumulated on your body. Alternatively,

one can also use a grounding strap.

• Touch the anti-static bag to a metal part of your computer chassis

before opening the bag.

• Take hold of the card only by the metal bracket when removing it out of

the bag.

After taking out the card, you should first:

• Inspect the card for any possible signs of external damage (loose or

damaged components, etc.). If the card is visibly damaged, please

notify our service department or our local sales representative immedi-

ately. Do not install a damaged card into your system.

Also, pay extra caution to the following aspects during installation:

• Avoid physical contact with materials that could hold static electricity

such as plastic, vinyl and Styrofoam.

• Whenever you handle the card, grasp it only by its edges. DO NOT

TOUCH the exposed metal pins of the connector or the electronic com-

ponents.

Page is loading ...

Advantech PCI-1718, PCI-1718 Series, PCI-1718HDU User manual

Related papers

Other documents