2. Home
  3. Home security & automation
  4. Digital Video Recorders (DVR)
  5. Vitek
  6. VT-HDOC16BR

Vitek VT-HDOC16BR User manual

  • Hello! I am an AI chatbot trained to assist you with the Vitek VT-HDOC16BR User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
VITEK
OnCue Bridge
8, & 16 Channel Complete
EX-SDI, TVI, AHD, CVI, Analog &
IP Recording Solution
• 8 & 16 Channel Stand-alone Real-time Video Recorders
• Supports IP, EX-SDI, TVI, AHD, CVI, Analog (CVBS) Cameras with automatic
format detection
• Full HD MegaPixel Real-time recording, live display, and playback
• Panorama (Thumbnail) Search
• HDMI 2.0 (4K), VGA, and BNC Outputs
• Plug and Play & Auto configuration for IP Cameras via OnVIF or generic protocol
• Point-Of-Sale (POS) Integration
• Alarm In/Out
• 2-way Full Duplex Audio
• Video Analytics with Search Feature (Camera Dependent)
• Remote Viewing via CMS Software, Internet Explorer, and Mobile Phones (iOS/
Android)
• Web-based remote configuration
• Advanced Video Detection: Camera tampering, Camera lens blocking, Day&Night,
Defocus
• Supports up to 30TB Internal Storage (VT-HDOC16BR) / 12TB Internal Storage
(VT-HDOC8BR)
• eSATA for storage extension of up to 5 more HDD
• Configurable Advanced Mirroring (Dual Recording, RAID1)
• RS-485 / CoC (Control Over Coax) PTZ Control
FEATURES
OnCue Bridge: Operation Manual
1
TABLE OF CONTENTS
1. BEFORE INSTALLING ............................................................................................................... 3
2. UPDATING SYSTEM F/W ......................................................................................................... 4
2.1 WITH A USB THUMB DRIVE .......................................................................................... 4
2.1.1 How to verify the F/W version .............................................................................. 4
2.1.2 Preparing new F/W (Type *.zip) in the USB thumb driver .................................... 5
2.1.3 Upgrading System from the System Menu .......................................................... 5
2.1.4 UPDATING FROM THE WEB MENU .............................................................. 6
2.2 DESCRIPTION OF REAR PANEL .................................................................................. 9
3. GETTING STARTED ................................................................................................................ 10
3.1 CONNECT AND SWITCH ON ....................................................................................... 10
3.2 NETWORK AUTOMATIC SET UP for PC, Mobile App ................................................. 12
4. TOOL BAR ............................................................................................................................... 15
4.1 STATUS DISPLAY ........................................................................................................ 15
4.2 LOG OFF ....................................................................................................................... 15
4.3 Main Menu POP-UP ...................................................................................................... 16
4.4 QUICK COPY MENU POP-UP ...................................................................................... 16
4.5 SEARCH MENU POP-UP ............................................................................................. 16
4.6 DISPLAY POP-UP ......................................................................................................... 17
4.7 PTZ POP-UP ................................................................................................................. 17
4.8 DIGITAL ZOOM ............................................................................................................. 18
4.9 LOG LIST ....................................................................................................................... 21
4.10 PANIC RECORD ......................................................................................................... 23
5. SEARCH & PLAYBACK ........................................................................................................... 24
5.1 TIME / CALENDAR SEARCH (Premium HD DVR) ....................................................... 24
5.2 PANORAMA SEARCH .................................................................................................. 26
5.2.1 BASIC OPERATION .......................................................................................... 26
5.3 EVENT SEARCH ........................................................................................................... 27
5.4 COPY ............................................................................................................................. 30
6. QUICK MENU .......................................................................................................................... 31
7. HOW TO CONFIGURE ............................................................................................................ 35
7.1 CONFIGURING CAMERA ............................................................................................. 35
7.1.1 TITLE ................................................................................................................. 35
7.1.2 ADJUST ............................................................................................................. 36
7.1.3 PTZ .................................................................................................................... 37
7.1.4 MOTION ............................................................................................................. 37
7.1.5 PRIVACY ........................................................................................................... 39
7.2 CONFIGURING DISPLAY ............................................................................................. 43
7.2.1 OSD ................................................................................................................... 43
7.2.2 MONITOR .......................................................................................................... 44
7.2.3 SEQUENCE ....................................................................................................... 45
7.2.4 SPOT ................................................................................................................. 45
7.3 CONFIGURING STORAGE ........................................................................................... 46
7.3.1 SETUP ............................................................................................................... 46
7.3.2 FORMAT ............................................................................................................ 47
7.3.3 NAS / FTP .......................................................................................................... 48
8.4. CONFIGURING SYSTEM ............................................................................................ 50
8.4.2. MANAGEMENT ................................................................................................ 51
7.3.4 AUDIO ................................................................................................................ 53
7.3.5 RS-485 ............................................................................................................... 53
8.5. CONFIGURING EVENT / SENSOR ............................................................................. 54
8.5.1. SENSOR INPUT ............................................................................................... 54
8.5.2. RELAY OUTPUT SETUP .................................................................................. 55
8.5.3. BUZZER OUTPUT SETUP ............................................................................... 56
8.5.4. E-MAIL SETUP ................................................................................................. 57
8.5.5. PTZ PRESET .................................................................................................... 57
8.5.6. PUSH ALARM ................................................................................................... 58
8.6. CONFIGURING USER ................................................................................................. 60
8.6.1. USER REGISTER ............................................................................................. 60
8.6.2. USER AUTHORITY .......................................................................................... 62
8.6.3. LOG-OUT .......................................................................................................... 63
8.7. CONFIGURING RECORD ............................................................................................ 64
OnCue Bridge: Operation Manual
2
8.7.1. SETUP .............................................................................................................. 64
8.7.2. EVENT .............................................................................................................. 65
8.7.3. SCHEDULE ....................................................................................................... 65
8.7.4. PANIC ............................................................................................................... 66
8.7.5. MISC ................................................................................................................. 67
8.8. CONFIGURING NETWORK ......................................................................................... 68
8.8.1. IP SETUP .......................................................................................................... 68
7.3.2 Local port ........................................................................................................... 69
8.8.2. DDNS ................................................................................................................ 69
8.8.4. E-MAIL .............................................................................................................. 71
9. REMOTE .................................................................................................................................. 72
9.1. WEB SERVER .............................................................................................................. 72
9.1.1. CONNECT TO WEB SERVER ......................................................................... 73
9.1.2. WEB CONFIGURATION PAGE ........................................................................ 74
9.1.3. WEB VIEWER (Active-X) .................................................................................. 75
9.2. Android Viewer / iOS Viewer ........................................................................................ 87
9.2.1. How to use ........................................................................................................ 87
9.3. DDNS SERVER ............................................................................................................ 89
9.3.1. HOW TO REGISTER ........................................................................................ 90
9.3.2. REGISTER ........................................................................................................ 90
9.3.3. Input DVR information. ...................................................................................... 91
9.4. OnCue Viewer .............................................................................................................. 92
9.4.1. INSTALLATION ................................................................................................. 92
9.4.2. EXECUTION ..................................................................................................... 93
9.4.3. LIVE VIDEO MONITORING .............................................................................. 93
9.4.4. CONNECTION MANAGER ............................................................................... 94
9.4.5. LIVE VIDEO WINDOW ..................................................................................... 96
9.4.6. PLAYER .......................................................................................................... 100
OnCue Bridge: Operation Manual
1
TABLE OF CONTENTS
1. BEFORE INSTALLING ............................................................................................................... 3
2. UPDATING SYSTEM F/W ......................................................................................................... 4
2.1 WITH A USB THUMB DRIVE .......................................................................................... 4
2.1.1 How to verify the F/W version .............................................................................. 4
2.1.2 Preparing new F/W (Type *.zip) in the USB thumb driver .................................... 5
2.1.3 Upgrading System from the System Menu .......................................................... 5
2.1.4 UPDATING FROM THE WEB MENU .............................................................. 6
2.2 DESCRIPTION OF REAR PANEL .................................................................................. 9
3. GETTING STARTED ................................................................................................................ 10
3.1 CONNECT AND SWITCH ON ....................................................................................... 10
3.2 NETWORK AUTOMATIC SET UP for PC, Mobile App ................................................. 12
4. TOOL BAR ............................................................................................................................... 15
4.1 STATUS DISPLAY ........................................................................................................ 15
4.2 LOG OFF ....................................................................................................................... 15
4.3 Main Menu POP-UP ...................................................................................................... 16
4.4 QUICK COPY MENU POP-UP ...................................................................................... 16
4.5 SEARCH MENU POP-UP ............................................................................................. 16
4.6 DISPLAY POP-UP ......................................................................................................... 17
4.7 PTZ POP-UP ................................................................................................................. 17
4.8 DIGITAL ZOOM ............................................................................................................. 18
4.9 LOG LIST ....................................................................................................................... 21
4.10 PANIC RECORD ......................................................................................................... 23
5. SEARCH & PLAYBACK ........................................................................................................... 24
5.1 TIME / CALENDAR SEARCH (Premium HD DVR) ....................................................... 24
5.2 PANORAMA SEARCH .................................................................................................. 26
5.2.1 BASIC OPERATION .......................................................................................... 26
5.3 EVENT SEARCH ........................................................................................................... 27
5.4 COPY ............................................................................................................................. 30
6. QUICK MENU .......................................................................................................................... 31
7. HOW TO CONFIGURE ............................................................................................................ 35
7.1 CONFIGURING CAMERA ............................................................................................. 35
7.1.1 TITLE ................................................................................................................. 35
7.1.2 ADJUST ............................................................................................................. 36
7.1.3 PTZ .................................................................................................................... 37
7.1.4 MOTION ............................................................................................................. 37
7.1.5 PRIVACY ........................................................................................................... 39
7.2 CONFIGURING DISPLAY ............................................................................................. 43
7.2.1 OSD ................................................................................................................... 43
7.2.2 MONITOR .......................................................................................................... 44
7.2.3 SEQUENCE ....................................................................................................... 45
7.2.4 SPOT ................................................................................................................. 45
7.3 CONFIGURING STORAGE ........................................................................................... 46
7.3.1 SETUP ............................................................................................................... 46
7.3.2 FORMAT ............................................................................................................ 47
7.3.3 NAS / FTP .......................................................................................................... 48
8.4. CONFIGURING SYSTEM ............................................................................................ 50
8.4.2. MANAGEMENT ................................................................................................ 51
7.3.4 AUDIO ................................................................................................................ 53
7.3.5 RS-485 ............................................................................................................... 53
8.5. CONFIGURING EVENT / SENSOR ............................................................................. 54
8.5.1. SENSOR INPUT ............................................................................................... 54
8.5.2. RELAY OUTPUT SETUP .................................................................................. 55
8.5.3. BUZZER OUTPUT SETUP ............................................................................... 56
8.5.4. E-MAIL SETUP ................................................................................................. 57
8.5.5. PTZ PRESET .................................................................................................... 57
8.5.6. PUSH ALARM ................................................................................................... 58
8.6. CONFIGURING USER ................................................................................................. 60
8.6.1. USER REGISTER ............................................................................................. 60
8.6.2. USER AUTHORITY .......................................................................................... 62
8.6.3. LOG-OUT .......................................................................................................... 63
8.7. CONFIGURING RECORD ............................................................................................ 64
OnCue Bridge: Operation Manual
2
8.7.1. SETUP .............................................................................................................. 64
8.7.2. EVENT .............................................................................................................. 65
8.7.3. SCHEDULE ....................................................................................................... 65
8.7.4. PANIC ............................................................................................................... 66
8.7.5. MISC ................................................................................................................. 67
8.8. CONFIGURING NETWORK ......................................................................................... 68
8.8.1. IP SETUP .......................................................................................................... 68
7.3.2 Local port ........................................................................................................... 69
8.8.2. DDNS ................................................................................................................ 69
8.8.4. E-MAIL .............................................................................................................. 71
9. REMOTE .................................................................................................................................. 72
9.1. WEB SERVER .............................................................................................................. 72
9.1.1. CONNECT TO WEB SERVER ......................................................................... 73
9.1.2. WEB CONFIGURATION PAGE ........................................................................ 74
9.1.3. WEB VIEWER (Active-X) .................................................................................. 75
9.2. Android Viewer / iOS Viewer ........................................................................................ 87
9.2.1. How to use ........................................................................................................ 87
9.3. DDNS SERVER ............................................................................................................ 89
9.3.1. HOW TO REGISTER ........................................................................................ 90
9.3.2. REGISTER ........................................................................................................ 90
9.3.3. Input DVR information. ...................................................................................... 91
9.4. OnCue Viewer .............................................................................................................. 92
9.4.1. INSTALLATION ................................................................................................. 92
9.4.2. EXECUTION ..................................................................................................... 93
9.4.3. LIVE VIDEO MONITORING .............................................................................. 93
9.4.4. CONNECTION MANAGER ............................................................................... 94
9.4.5. LIVE VIDEO WINDOW ..................................................................................... 96
9.4.6. PLAYER .......................................................................................................... 100
OnCue Bridge: Operation Manual
3
1. BEFORE INSTALLING
• Installation should be carried out only by qualified personnel and in accordance with electrical regulations in
force.
• The DVR must be placed on a stable surface or mounted in an approved cabinet. Adequate ventilation must
be provided, taking particular care not to block any of the air vents on the DVR.
• Adequate protection against lightning strikes and power surges must be installed to prevent damage to the
DVR.
• Any safety warnings on the DVR and in these instructions must be adhered to.
• If cleaning is necessary, shutdown the DVR and disconnect the power source first. Use a soft dry cloth only –
never use an abrasive cleaner.
• Do not attempt to service or repair the DVR as opening or removing covers may expose dangerous voltages
or other hazards. Refer all servicing to qualified service personnel
OnCue Bridge: Operation Manual
4
2. UPDATING SYSTEM F/W
2.1 WITH A USB THUMB DRIVE
User can upgrade the system firmware if required. F/W upgrading could be required to increase the
stability and the reliability or apply new updated features. The following steps are a process to
upgrade the f/w
.
VerifythecurrentF/Wversion
PreparenewF/WintheUSBthumbdrive
Dotheupgradingprocess
2.1.1 How to verify the F/W version
You may need to check the F/W version provided and the F/W version currently used in the
system. From the Setup=>SYSTEM=>MANAGEMENT=>INFO, you can see the current version of
F/W.
F/W version of new provided one: From the filename of the provided F/W file,
you can see the version number.
Check the F/W version.
Ø The ‘FW_X.XXX_UI_Y.Y.YS’ in the file
name means the F/W version.
Do not update F/W if the version number of F/W file is lower than the current F/W version.
OnCue Bridge: Operation Manual
3
1. BEFORE INSTALLING
• Installation should be carried out only by qualified personnel and in accordance with electrical regulations in
force.
• The DVR must be placed on a stable surface or mounted in an approved cabinet. Adequate ventilation must
be provided, taking particular care not to block any of the air vents on the DVR.
• Adequate protection against lightning strikes and power surges must be installed to prevent damage to the
DVR.
• Any safety warnings on the DVR and in these instructions must be adhered to.
• If cleaning is necessary, shutdown the DVR and disconnect the power source first. Use a soft dry cloth only –
never use an abrasive cleaner.
• Do not attempt to service or repair the DVR as opening or removing covers may expose dangerous voltages
or other hazards. Refer all servicing to qualified service personnel
OnCue Bridge: Operation Manual
4
2. UPDATING SYSTEM F/W
2.1 WITH A USB THUMB DRIVE
User can upgrade the system firmware if required. F/W upgrading could be required to increase the
stability and the reliability or apply new updated features. The following steps are a process to
upgrade the f/w
.
VerifythecurrentF/Wversion
PreparenewF/WintheUSBthumbdrive
Dotheupgradingprocess
2.1.1 How to verify the F/W version
You may need to check the F/W version provided and the F/W version currently used in the
system. From the Setup=>SYSTEM=>MANAGEMENT=>INFO, you can see the current version of
F/W.
F/W version of new provided one: From the filename of the provided F/W file,
you can see the version number.
Check the F/W version.
Ø The ‘FW_X.XXX_UI_Y.Y.YS’ in the file
name means the F/W version.
Do not update F/W if the version number of F/W file is lower than the current F/W version.
OnCue Bridge: Operation Manual
5
2.1.2 Preparing new F/W (Type *.zip) in the USB thumb driver
1) Unzip firmware file.
After unzipped, you can see above system file.
According to Upgrade, the number of downloaded files might be different.
2) Make a folder in the root of the USB thumb drive labelled ‘dvr’.
The characters, ‘d’,’v’,’r’, in the folder name have to be in lower case not capitals.
3) Copy the unzipped files into the ‘dvr’ folder in the USB thumb drive.
2.1.2.1 Preparing new F/W (Type *.tgz) in the USB thumb driver
1) Copy the released F/W *.tgz file into the root of the USB thumb drive.
2.1.3 Upgrading System from the System Menu
Following steps will guide you to upgrade the system with the new F/W.
1) Plug the prepared USB thumb drive into the USB port of NVR.
2) Open Setup=>SYSTEM=>MANAGEMENT menu.
3) Click ‘UPGRADE’ button.
4) Checking the Product code.
OnCue Bridge: Operation Manual
6
If the product codes are different, the upgrade will not be processed
ProductCode:Press‘OKbuttonthenprocessthefirmwareupgrade
The whole upgrading process may take 1~5 minutes.
DO NOT remove the USB thumb driver during upgrade.
DO NOT turn off power to the system during upgrade.
5) When the firmware upgrade is finished, system will reboot automatically.
2.1.4 UPDATING FROM THE WEB MENU
The web menu service in the DVR provides a way to update the system F/W remotely. The
following steps explain how to do this.
To access the internal web menu service, refer to section 7.1, ‘WEB SERVER’ of this user’s
guide.
1) Login the DVR through the web server.
2) Enter the ‘SYSTEM MANAGEMENT’ page under the ‘SYSTEM’ menu page. Refer to
the below picture.
OnCue Bridge: Operation Manual
5
2.1.2 Preparing new F/W (Type *.zip) in the USB thumb driver
1) Unzip firmware file.
After unzipped, you can see above system file.
According to Upgrade, the number of downloaded files might be different.
2) Make a folder in the root of the USB thumb drive labelled ‘dvr’.
The characters, ‘d’,’v’,’r’, in the folder name have to be in lower case not capitals.
3) Copy the unzipped files into the ‘dvr’ folder in the USB thumb drive.
2.1.2.1 Preparing new F/W (Type *.tgz) in the USB thumb driver
1) Copy the released F/W *.tgz file into the root of the USB thumb drive.
2.1.3 Upgrading System from the System Menu
Following steps will guide you to upgrade the system with the new F/W.
1) Plug the prepared USB thumb drive into the USB port of NVR.
2) Open Setup=>SYSTEM=>MANAGEMENT menu.
3) Click ‘UPGRADE’ button.
4) Checking the Product code.
OnCue Bridge: Operation Manual
6
If the product codes are different, the upgrade will not be processed
ProductCode:Press‘OKbuttonthenprocessthefirmwareupgrade
The whole upgrading process may take 1~5 minutes.
DO NOT remove the USB thumb driver during upgrade.
DO NOT turn off power to the system during upgrade.
5) When the firmware upgrade is finished, system will reboot automatically.
2.1.4 UPDATING FROM THE WEB MENU
The web menu service in the DVR provides a way to update the system F/W remotely. The
following steps explain how to do this.
To access the internal web menu service, refer to section 7.1, ‘WEB SERVER’ of this user’s
guide.
1) Login the DVR through the web server.
2) Enter the ‘SYSTEM MANAGEMENT’ page under the ‘SYSTEM’ menu page. Refer to
the below picture.
OnCue Bridge: Operation Manual
7
3) Click the button ‘UPGRADE’ and open the update page.
4) In ‘F/W Update’ pop-up, click the ‘BROWSE’ button and locate and select the firmware.
5) Choose the provided F/W file which has the file extension ‘tar.gz or tgz’.
6) Click the ‘UPLOAD’ button to upload the F/W to the system.
7) After the firmware has uploaded, the system will be ready for the update. Click the ‘START’
button to begin the updating processes.
If the product code is different, the upgrade will not be processed
8) During the update, the progress will be displayed (see below).
OnCue Bridge: Operation Manual
8
9) When the update is completed, the DVR will restart.
The whole upgrading process may take 5~10 minutes depending on the network.
DO NOT disconnect the network during upgrade.
DO NOT turn off power to the system during upgrade.
OnCue Bridge: Operation Manual
7
3) Click the button ‘UPGRADE’ and open the update page.
4) In ‘F/W Update’ pop-up, click the ‘BROWSE’ button and locate and select the firmware.
5) Choose the provided F/W file which has the file extension ‘tar.gz or tgz’.
6) Click the ‘UPLOAD’ button to upload the F/W to the system.
7) After the firmware has uploaded, the system will be ready for the update. Click the ‘START’
button to begin the updating processes.
If the product code is different, the upgrade will not be processed
8) During the update, the progress will be displayed (see below).
OnCue Bridge: Operation Manual
8
9) When the update is completed, the DVR will restart.
The whole upgrading process may take 5~10 minutes depending on the network.
DO NOT disconnect the network during upgrade.
DO NOT turn off power to the system during upgrade.
OnCue Bridge: Operation Manual
9
2.2 DESCRIPTION OF REAR PANEL
① ②
③
④ ⑤
⑥
⑦ ⑧
⑨
⑩ ⑪⑪ ⑫
[RearpanelofBridgeAll-in-one4chDVR]
①
② ③
④
⑤
⑥
⑦
⑧ ⑨
⑩
⑪
⑫
[RearpanelofBridgeAll-in-one8chDVR]
⑥ ⑦
⑧ ⑨
④① ② ③
⑤
⑩
⑪ ⑫
[RearpanelofBridgeAll-in-one16chDVR]
OnCue Bridge: Operation Manual
10
1.HD-SDIorAnalogCameraInput
EX-SDI/HD-SDI / Analog HD Camera input
(AnalogHD/TVI/CVI/960H)  
2.AudioInputs
RCAconnectorsfortaudiosignalinput
(4xAudioIn)
3.Alarm(Sensor)Inputs,RS-485,andRelayOutput
• Alarm (16ch: 16 x Input, 8ch: 8 x Input, 4ch: 4 x
input)  
• RS-485 Signals. (D+: RX/TX + signal, D-: RX/TX-
signal)
• Relay output for relay 2 (NO: Normal Open, NC:
NormalClosed,CM:Common)
4.eSATAConnectionPort(Option)
connect e-SATA storage to expand HDD
5.AudioOutput
RCAconnectorforaudiosignalout.(Lineout)
6.CVBSMonitorOutput&TVIHDSpot
Composite video output for the spot live screen. (
BNC&TVI-FullHDfor8/16ch)
7.VGAOutput(VideoGraphicArray)
15-pinD-subconnectorfortheanalogueVGAoutput.
8.DIGITALVIDEOOUT
Digitalvideooutputforthemainmonitor(HDMI).
9.RJ-45NetworkPort(1GBase-T)
• PortforIPcamera
• 8&16ch:1Gbase-T(Ethernet&LocalPort)
• 4ch:100Mbase-T(EthernetPort)
10.RearUSB2.0ports
USB 2.0 ports. Provides functions ‘Copy to USB
storage’, ‘F/W Upgrade’ and ‘mouse’ operation.
11.PowerIn
12VDCPowersocket.
12.PowerSwitch
SwitchtoturntheDVRON&OFF.
3. GETTING STARTED
3.1 CONNECT AND SWITCH ON
w ConnectHD/AnalogcamerastocamerainputsonthebackoftheDVR.
w ConnectoneormoremonitorstoDVRusingDigitalVideooutput,VGAandCVBS.
w ConnectpowertoDVR.PressthepowerbuttononthebackpanelofDVRtobeginoperation.
[Logo Image]
Initialsetresolutionis1280x1024,soyoushouldusemonitorhigherthan1280x1024
OnCue Bridge: Operation Manual
9
2.2 DESCRIPTION OF REAR PANEL
① ②
③
④ ⑤
⑥
⑦ ⑧
⑨
⑩ ⑪⑪ ⑫
[RearpanelofBridgeAll-in-one4chDVR]
①
② ③
④
⑤
⑥
⑦
⑧ ⑨
⑩
⑪
⑫
[RearpanelofBridgeAll-in-one8chDVR]
⑥ ⑦
⑧ ⑨
④① ② ③
⑤
⑩
⑪ ⑫
[RearpanelofBridgeAll-in-one16chDVR]
OnCue Bridge: Operation Manual
10
1.HD-SDIorAnalogCameraInput
EX-SDI/HD-SDI / Analog HD Camera input
(AnalogHD/TVI/CVI/960H)  
2.AudioInputs
RCAconnectorsfortaudiosignalinput
(4xAudioIn)
3.Alarm(Sensor)Inputs,RS-485,andRelayOutput
• Alarm (16ch: 16 x Input, 8ch: 8 x Input, 4ch: 4 x
input)  
• RS-485 Signals. (D+: RX/TX + signal, D-: RX/TX-
signal)
• Relay output for relay 2 (NO: Normal Open, NC:
NormalClosed,CM:Common)
4.eSATAConnectionPort(Option)
connect e-SATA storage to expand HDD
5.AudioOutput
RCAconnectorforaudiosignalout.(Lineout)
6.CVBSMonitorOutput&TVIHDSpot
Composite video output for the spot live screen. (
BNC&TVI-FullHDfor8/16ch)
7.VGAOutput(VideoGraphicArray)
15-pinD-subconnectorfortheanalogueVGAoutput.
8.DIGITALVIDEOOUT
Digitalvideooutputforthemainmonitor(HDMI).
9.RJ-45NetworkPort(1GBase-T)
• PortforIPcamera
• 8&16ch:1Gbase-T(Ethernet&LocalPort)
• 4ch:100Mbase-T(EthernetPort)
10.RearUSB2.0ports
USB 2.0 ports. Provides functions ‘Copy to USB
storage’, ‘F/W Upgrade’ and ‘mouse’ operation.
11.PowerIn
12VDCPowersocket.
12.PowerSwitch
SwitchtoturntheDVRON&OFF.
3. GETTING STARTED
3.1 CONNECT AND SWITCH ON
w ConnectHD/AnalogcamerastocamerainputsonthebackoftheDVR.
w ConnectoneormoremonitorstoDVRusingDigitalVideooutput,VGAandCVBS.
w ConnectpowertoDVR.PressthepowerbuttononthebackpanelofDVRtobeginoperation.
[Logo Image]
Initialsetresolutionis1280x1024,soyoushouldusemonitorhigherthan1280x1024
OnCue Bridge: Operation Manual
11
[Loading….]
When DVR is prepared for initial operation, display screen as above and shows booting progress.
Fromloadingscreendisplay,recordingstartsaccordingtopre-setcondition.
Whenloading,screencouldbeflashingoddcolorswhileDVRisprocessingtooptimizedisplay.
All operation of DVR is ready, automatically log-in and show as below screen.
OnCue Bridge: Operation Manual
12
Loginwithremotecontrol,operateasbelow
Ø Using direction button, move to user’s selected menu, press “enter” on remote control and
move to user account selection mode.
Ø Using Up/Down key, select account, and press “Enter” on remote control for selecting user’s
account
Ø Using numeric key and input pin code,
Ø If required, using direction key and move to virtual keyboard and input pin code.
Ø After inputting pin code, using direction key, move to ‘enter’ or ‘confirm’ over virtual keyboard
and press ‘enter’ ( ) to log-in
[Live mode of 16 channels]
Bottom of screen shows the tool-bar for operation. Tool bar has current time and date, network connection
status ( ), back up storage connection status ( ), automatic screen switch operation ( ), HDD
installation ( ), currently working audio ( ). Also tool bar includes log on/off for DVR operation ( ),
Setup menu ( ), VA related menu button ( ), easy copy button ( ), search ( ), Screen display
selection ( ), Pan/tilt ( ), Digital zoom ( ), system log ( ), Panic button ( )
3.2 NETWORK AUTOMATIC SET UP for PC, Mobile App
OnCue Bridge: Operation Manual
11
[Loading….]
When DVR is prepared for initial operation, display screen as above and shows booting progress.
Fromloadingscreendisplay,recordingstartsaccordingtopre-setcondition.
Whenloading,screencouldbeflashingoddcolorswhileDVRisprocessingtooptimizedisplay.
All operation of DVR is ready, automatically log-in and show as below screen.
OnCue Bridge: Operation Manual
12
Loginwithremotecontrol,operateasbelow
Ø Using direction button, move to user’s selected menu, press “enter” on remote control and
move to user account selection mode.
Ø Using Up/Down key, select account, and press “Enter” on remote control for selecting user’s
account
Ø Using numeric key and input pin code,
Ø If required, using direction key and move to virtual keyboard and input pin code.
Ø After inputting pin code, using direction key, move to ‘enter’ or ‘confirm’ over virtual keyboard
and press ‘enter’ ( ) to log-in
[Live mode of 16 channels]
Bottom of screen shows the tool-bar for operation. Tool bar has current time and date, network connection
status ( ), back up storage connection status ( ), automatic screen switch operation ( ), HDD
installation ( ), currently working audio ( ). Also tool bar includes log on/off for DVR operation ( ),
Setup menu ( ), VA related menu button ( ), easy copy button ( ), search ( ), Screen display
selection ( ), Pan/tilt ( ), Digital zoom ( ), system log ( ), Panic button ( )
3.2 NETWORK AUTOMATIC SET UP for PC, Mobile App
OnCue Bridge: Operation Manual
13
Right click of mouse on Live mode, select Network SETUP WIZARD
Step 1.
1. Mobile APP install.
You can install “OnCueviewer” for Android phone, “iOnCueviewer” for I-phone.
2. P2P connection activation.
Move to dvr registration menu on mobile app and activate P2P.
If you want to receive dvr event on mobile app, then activate push alarm.
3. QR code use
On mobile app, you can move to registration of P2P and take picture of the QR code
4. Click Next below
Step 2.
1. Email account registration
Network set up information, Self-Diagnosis result,
DVR event can be reported by email if you fill in below.
2. Password set up
Please fill in password for ADMIN to access remotely and locally.
3. Use above password when you register DVR to mobile APP.
4. Click below Next and start automatic set up.
OnCue Bridge: Operation Manual
14
Click Next, then you can receive report by email.
Network automatic setting report
- Device IP address: 192.168.123.174
- Global IP: 000.000.000.000
- Subnet mask: 255.255.255.0
- DNS server address:
- DVR port:
- Automatically assigned ddns address: xxxxxxxx.ns.oncueddns.com
Step 3.
1. We are setting up network automatically, it require 1 to 2 minutes depending on network situation.
2. When success, you can check connection on mobile phone
Step 4.
Network automatic set up completed.
You can select newly registered DVR on mobile app and click “connect” button you can confirm connection.
If you want to receive report by email, you can click right marked email transmission button
OnCue Bridge: Operation Manual
13
Right click of mouse on Live mode, select Network SETUP WIZARD
Step 1.
1. Mobile APP install.
You can install “OnCueviewer” for Android phone, “iOnCueviewer” for I-phone.
2. P2P connection activation.
Move to dvr registration menu on mobile app and activate P2P.
If you want to receive dvr event on mobile app, then activate push alarm.
3. QR code use
On mobile app, you can move to registration of P2P and take picture of the QR code
4. Click Next below
Step 2.
1. Email account registration
Network set up information, Self-Diagnosis result,
DVR event can be reported by email if you fill in below.
2. Password set up
Please fill in password for ADMIN to access remotely and locally.
3. Use above password when you register DVR to mobile APP.
4. Click below Next and start automatic set up.
OnCue Bridge: Operation Manual
14
Click Next, then you can receive report by email.
Network automatic setting report
- Device IP address: 192.168.123.174
- Global IP: 000.000.000.000
- Subnet mask: 255.255.255.0
- DNS server address:
- DVR port:
- Automatically assigned ddns address: xxxxxxxx.ns.oncueddns.com
Step 3.
1. We are setting up network automatically, it require 1 to 2 minutes depending on network situation.
2. When success, you can check connection on mobile phone
Step 4.
Network automatic set up completed.
You can select newly registered DVR on mobile app and click “connect” button you can confirm connection.
If you want to receive report by email, you can click right marked email transmission button
OnCue Bridge: Operation Manual
15
*Device IP Address: Displays the internal IP address of the network environment where the DVR is installed.
*Global IP Address: Displays the external IP address of the network environment where the DVR is installed.
*SUBNET MASK: Displays the SUBNET MASK of the network environment where the DVR is installed.
*DNS Server: Displays the DNS Server of the network environment where the DVR is installed.
*DVR Port: Displays DVR port
*Automatic DDNS Address: Displays the DVR DDNS
*Web browser address: DVR address when access web browser
*PUSH ALARM: Ready for Push Alarm
*P2P Connection: Ready for P2P
*DHCP (Automatic IP Allocation): Ready for DHCP
4. TOOL BAR
You can view the following Tool Bar when you move the mouse to the bottom of screen.
The Tool-bar displays when the mouse pointer moves to bottom of screen, disappears after pre-defined menu
setting time or exit with exit button ( ). In the menu you can set to display all the time.
4.1 STATUS DISPLAY
You can check the current time / Network connection/ USB storage connection/ Auto sequence/ HDD location
currently recording / Audio.
: Display current time.(Year / Mouth / Day / Hour / Minute / Second)
: Shows Network connection.
: Shows USB Storage connection
: Shows Auto sequence
: Shows HDD location which is currently recording.
: Shows default audio channel.
4.2 LOG OFF
There are two ways to log off. One is manual log off and the other one is to automatic log off after configured
amount of time.
OnCue Bridge: Operation Manual
16
To manually log off click log off/on button as seen below
[Log-Off by using TOOL BAR]
Once Log off is selected as above, current account can be logged off.
Log Off: After logging off, the login window like the initial screen will be displayed after
booting the DVR, and the login method is the same as the initial login.
Onceyoulogoff,youwillnotbeabletooperatetheDVRuntilyouloginagain.
[Howtologoffautomaticallyusingmenusettings]
Under Main Setting Menu, user-> log out, you can set up automatic log off after certain time period.
4.3 Main Menu POP-UP
Click the main menu button, main menu will POP-UP.
4.4 QUICK COPY MENU POP-UP
Click the following icon, instant Backup menu will pop up. You can save the data 10 minutes from the current
time.
4.5 SEARCH MENU POP-UP
To search a particular section of recorded footage, press the SEARCH button.
To protect unauthorized viewing of footage, only authorized users can playback footage.
OnCue Bridge: Operation Manual
15
*Device IP Address: Displays the internal IP address of the network environment where the DVR is installed.
*Global IP Address: Displays the external IP address of the network environment where the DVR is installed.
*SUBNET MASK: Displays the SUBNET MASK of the network environment where the DVR is installed.
*DNS Server: Displays the DNS Server of the network environment where the DVR is installed.
*DVR Port: Displays DVR port
*Automatic DDNS Address: Displays the DVR DDNS
*Web browser address: DVR address when access web browser
*PUSH ALARM: Ready for Push Alarm
*P2P Connection: Ready for P2P
*DHCP (Automatic IP Allocation): Ready for DHCP
4. TOOL BAR
You can view the following Tool Bar when you move the mouse to the bottom of screen.
The Tool-bar displays when the mouse pointer moves to bottom of screen, disappears after pre-defined menu
setting time or exit with exit button ( ). In the menu you can set to display all the time.
4.1 STATUS DISPLAY
You can check the current time / Network connection/ USB storage connection/ Auto sequence/ HDD location
currently recording / Audio.
: Display current time.(Year / Mouth / Day / Hour / Minute / Second)
: Shows Network connection.
: Shows USB Storage connection
: Shows Auto sequence
: Shows HDD location which is currently recording.
: Shows default audio channel.
4.2 LOG OFF
There are two ways to log off. One is manual log off and the other one is to automatic log off after configured
amount of time.
OnCue Bridge: Operation Manual
16
To manually log off click log off/on button as seen below
[Log-Off by using TOOL BAR]
Once Log off is selected as above, current account can be logged off.
Log Off: After logging off, the login window like the initial screen will be displayed after
booting the DVR, and the login method is the same as the initial login.
Onceyoulogoff,youwillnotbeabletooperatetheDVRuntilyouloginagain.
[Howtologoffautomaticallyusingmenusettings]
Under Main Setting Menu, user-> log out, you can set up automatic log off after certain time period.
4.3 Main Menu POP-UP
Click the main menu button, main menu will POP-UP.
4.4 QUICK COPY MENU POP-UP
Click the following icon, instant Backup menu will pop up. You can save the data 10 minutes from the current
time.
4.5 SEARCH MENU POP-UP
To search a particular section of recorded footage, press the SEARCH button.
To protect unauthorized viewing of footage, only authorized users can playback footage.
OnCue Bridge: Operation Manual
17
4.6 DISPLAY POP-UP
Configure display mode by pressing display button of Tool bar.
Select Quad / Single/ Auto sequence by selecting item in pop-up menu.
: Single Screen Mode
: Quad Screen Mode.
: 9-split Mode.
: 16-split Mode.
: Auto Sequence Mode.
: Auto Sequence Mode of Spot output
4.7 PTZ POP-UP
Move to the PTZ control mode.
When the display mode is in quad, the PTZ control panel will be opened for the selected camera which is
previously highlighted by mouse click. If there is not a highlighted camera, the PTZ control panel is opened for
controlling camera 1. In single display mode, the PTZ control panel is opened for the currently displayed
camera.
SupportonlyafterPTZIPcameraintegrationwithDVRiscompleted.
TocontrolPan/Tilt,youneedtosetthePan/TiltMenu
SupportedPTZprotocols.
Ø PELCO-D
Ø PELCO-P
Ø SAMSUNG-T
OnCue Bridge: Operation Manual
18
Ø SAMSUNG-E
Ø EZ
Ø HIK TYPE 1
Ø VITEK CoC
[PTZ Controller Screen]
1: Select channel for PTZ control.
2: Number to configure Preset.
3: Select the tour function start or end.
4: Control the PTZ.
5: Change the size of control box.
6: Display PTZ control parameters which are set under the ‘DETAIL’ of PTZ
menu settings
7: execute automatic focus.
8: execute auto scan.
4.8 DIGITAL ZOOM
You can move to the Zoom mode by selecting the menu in Tool bar.
You can use the mouse (Drag) or tool bar to zoom in or Zoom out.
[Zoom by using TOOL BAR]
Split screen mode, you have to enter Zoom mode through channel number 1.
At Full screen mode, you can enter Zoom mode at current Full screen.
OnCue Bridge: Operation Manual
17
4.6 DISPLAY POP-UP
Configure display mode by pressing display button of Tool bar.
Select Quad / Single/ Auto sequence by selecting item in pop-up menu.
: Single Screen Mode
: Quad Screen Mode.
: 9-split Mode.
: 16-split Mode.
: Auto Sequence Mode.
: Auto Sequence Mode of Spot output
4.7 PTZ POP-UP
Move to the PTZ control mode.
When the display mode is in quad, the PTZ control panel will be opened for the selected camera which is
previously highlighted by mouse click. If there is not a highlighted camera, the PTZ control panel is opened for
controlling camera 1. In single display mode, the PTZ control panel is opened for the currently displayed
camera.
SupportonlyafterPTZIPcameraintegrationwithDVRiscompleted.
TocontrolPan/Tilt,youneedtosetthePan/TiltMenu
SupportedPTZprotocols.
Ø PELCO-D
Ø PELCO-P
Ø SAMSUNG-T
OnCue Bridge: Operation Manual
18
Ø SAMSUNG-E
Ø EZ
Ø HIK TYPE 1
Ø VITEK CoC
[PTZ Controller Screen]
1: Select channel for PTZ control.
2: Number to configure Preset.
3: Select the tour function start or end.
4: Control the PTZ.
5: Change the size of control box.
6: Display PTZ control parameters which are set under the ‘DETAIL’ of PTZ
menu settings
7: execute automatic focus.
8: execute auto scan.
4.8 DIGITAL ZOOM
You can move to the Zoom mode by selecting the menu in Tool bar.
You can use the mouse (Drag) or tool bar to zoom in or Zoom out.
[Zoom by using TOOL BAR]
Split screen mode, you have to enter Zoom mode through channel number 1.
At Full screen mode, you can enter Zoom mode at current Full screen.
OnCue Bridge: Operation Manual
19
: You can move Zoom Box
: If you press this button, you can control zoom box by 5 levels.
CurrentlyZoomingscreen.
[ZoombyusingMouse]
OnCue Bridge: Operation Manual
20
At full screen mode, you can select the area to zoom in/out by clicking left button of Mouse. (Drag), Clicking on
the zoomed screen, the display returns to the original screen.
Digital Zoom supported in Live / Play mode
Digital Zoom supported at Full screen mode only.
/