Tyan Tempest i5000V S5370 User manual

1

Tempest i5000VF

///

S5370

Version 1.2

Copyright

this manual may be reproduced or translated without prior written consent from

TYAN Computer Corp.

Trademark

All registered and unregistered trademarks and company names contained in

this manual are property of their respective owners including, but not limited to

the following.

TYAN, Tempest i5000VF are trademarks of TYAN Computer Corporation.

Intel, Blackford-VS, and combinations thereof are trademarks of Intel

Corporation.

Phoenix, Phoenix-AwardBIOS are trademarks of Phoenix Technologies.

Microsoft, Windows are trademarks of Microsoft Corporation.

SuSE,is a trademark of SuSE AG.

IBM, PC, AT, and PS/2 are trademarks of IBM Corporation.

Notice

Information contained in this document is furnished by TYAN Computer

Corporation and has been reviewed for accuracy and reliability prior to printing.

TYAN assumes no liability whatsoever, and disclaims any express or implied

warranty, relating to sale and/or use of TYAN products including liability or

warranties relating to fitness for a particular purpose or merchantability. TYAN

retains the right to make changes to product descriptions and/or specifications

at any time, without notice. In no event will TYAN be held liable for any direct or

indirect, incidental or consequential damage, loss of use, loss of data or other

malady resulting from errors or inaccuracies of information contained in this

document.

2

Table of Contents

Check the box contents! 3

Chapter 1: Introduction

1.1 Congratulations…………………………………………………………… 5

1.2 Hardware Specifications………………………………………………… 5

Chapter 2: Board Installation

2.1 Board Image……………………………………………………………… 8

2.2 Block Diagram……………………………………………………………. 9

2.3 Board Parts, Jumpers and Connectors………………………………... 10

2.4 Tips on Installing Motherboard in Chassis…………………………….. 19

2.5 Installing the Processor(s)………………………………....................... 20

2.6 Installing the Memory……………………………………………………. 23

2.7 Attaching Drive Cables………………………………………………….. 25

2.8 Installing Add-in Cards………………………………............................ 27

2.9 Connecting External Devices…………………………………………… 28

2.10 Installing the Power Supply……………………………………………... 29

2.11 Finishing up………………………………………………………………. 29

Chapter 3: BIOS Setup

3.1 About the BIOS…………………………………………………………… 31

3.2 BIOS Main Menu…………………………………………………………. 33

3.3 Advanced Menu………………………………………………………….. 41

3.4 Security Menu…………………………………………………………….. 55

3.5 Power Menu………………………………………………………………. 56

3.6 Boot Menu………………………………………………………………… 57

3.7 Exit Menu…………………………………………………………………. 58

Chapter 4: Diagnostics

4.1 Beep Codes………………………………………………………………. 59

4.2 Flash Utility……………………………………………………………….. 59

4.3 BIOS Post Code………………………………………………………….. 60

Appendix I: SMDC Information

Appendix II: How to Make a Driver Diskette

Glossary

3

Check the box contents!

1x S5370 motherboard

1x 34-Pin floppy drive cable

1 x Ultra-DMA-133/100/66/33 IDE cable

3 x Serial ATA power cable

6 x Serial ATA Cable

1 x USB2.0 cable

1 x S5370 user’s manual

1 x S5370 Quick Reference guide

1 x TYAN driver CD

1 x I/O shield

2 x CPU Back Plane

If any of these items are missing, please contact your vendor/dealer for

replacement before continuing with the installation process.

4

5

Chapter 1: Introduction

1.1 - Congratulations

You have purchased one of the most powerful server solutions. The Tempest

i5000VF (S5370) is a flexible Intel

®

platform for multiple applications, based on

Intel

®

“Blackford-VS” MCH and ESB2 chipsets.

Designed to support Intel

®

Xeon 5000/5100/5300 series processor and 16GB

DDR2-533/667 FB-DIMM memory, and featured with integrated Dual Gigabit

Ethernet LAN, built-in 16MB XGI XG20

TM

video plus six serial ATA ports, the

S5370 offers exceptional performance and versatile solution for your server

platform.

Remember to visit TYAN’s Website at http://www.TYAN.com. There you can

find information on all of TYAN’s products with FAQs, online manuals and BIOS

upgrades.

1.2 - Hardware Specifications

Processor

•Dual LGA771 sockets

•Supports up to two Intel

®

Xeon

5000/5100 series processors

•Supports up to two Intel

®

Xeon

5300 series processors

•667/1066/1333 MHz FSB

•VRD 11.0

Chipset

•Intel

®

“Blackford-VS” MCH+ESB2

chipset

•SMSC SCH5017 super I/O chip

Memory

•Four 240-pin DDR2 FBDIMM

sockets

•2 memory channels

•Supports ECC DIMMs

•Maximum of 16/8GB DDR2-

533/667 FB-DIMM*

Integrated LAN Controllers

•Intel

®

Gigabit from ESB2

(w/”Gilgal”) (ASF2.0 option)

•Two front panel LED headers

(Link/Act)

•Two RJ-45 port with LEDs

Integrated Video Controller

•XGI XG20

•PCI interface

•16MB DDR memory

Integrated SATA 2.0 Controller

•Six SATA2.0 ports from Intel

ESB2

•Integrated RAID 0/1/5/10 support

BIOS

•Phoenix

®

BIOS on 8Mbit Flash

ROM

•Supports ACPI 1.0b

6

*FB-DIMM: Fully Buffered DIMM

Expansion Slots

•Two (2) PCI-Express x8 slots

(with x4 signal)

•One (1) PCI-X 133/100MHz slot

•Two (2) PCI 32-bit 33MHz slots

Total Five expansion slots from

ESB2

Integrated I/O

•One (1) 9-pin 16550 UART serial

port

•One (1) 15-pin VGA port

•Eight (8) USB2.0 ports (two ports

at rear, three front headers

support six ports)

•PS/2 mouse and keyboard

connectors

•One (1) FDD connector

•One (1) IDE connector supports

ATA100

•Six standard/integrated SATA

connectors

•Two side by side RJ-45

10/100/1000 LAN ports

System Management

•Winbond W83793G Hardware

Monitor ASIC

•CPU thermal & voltage monitor

support

•2-pin chassis intrusion header

•4-pin fan monitoring header

•Five (5) fan headers with

Tachometer and auto fan control

(4-pin configuration)

•Serial Console Redirect

•PXE via Ethernet, USB device

boot

•User-configurable H/W monitoring

•Auto-configuration of hard disk

types

•Multiple boot options

•48-bit LBA support

Form Factor

•SSI/CEB 1.01 (12” x 10.5”)

•EPS12V/SSI (24+8pin) power

connectors

•Stacked PS/2 keyboard and

mouse connectors

•Stacked USB2.0 (2) connectors

•Serial (1) and VGA (1) connectors

•Two side-by-side RJ-45 LAN

connectors with LEDs

7

Chapter 2: Board Installation

You are now ready to install your motherboard. The mounting hole pattern of

the Tempest i5000VF S5370 matches the ATX specification. Before continuing

with installation, confirm that your chassis supports an ATX motherboard.

How to install our products right… the first time

The first thing you should do is reading this user’s manual. It contains important

information that will make configuration and setup much easier. Here are some

precautions you should take when installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the

antistatic bag. Unplug the power from your computer power supply and

then touch a safely grounded object to release static charge (i.e. power

supply case). For the safest conditions, TYAN recommends wearing a

static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the

board, or flex the board in any way.

(3) Avoid touching the motherboard components, IC chips, connectors,

memory modules, and leads.

(4) Place the motherboard on a grounded antistatic surface or on the

antistatic bag that the board was shipped in.

(5) Inspect the board for damage.

The following pages include details on how to install your motherboard into your

chassis, as well as installing the processor, memory, disk drives and cables.

NOTE

DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN

DAMAGED

8

2.1- Board Image

This picture is representative of the latest board revision available at

the time of publishing. The board you receive may or may not look

exactly like the above picture.

9

2.2 - Block Diagram

Tempest i5000VF S5370 Block Diagram

10

2.3 - Board Parts, Jumpers and Connectors

DIMM 2

DIMM 1

DIMM 0

CN1

CN3

KB/MS

USB x 2

COM1

VGA

LAN1

LAN2

CN23

CN22

BIOS

PCIE1

PCIE3

PCIX1

BMC1

PCI1PCI1

PCI2

CN12

JP16

CN26

SATA0

SATA1

SATA4

SATA2 SATA5

SATA3

CN15

CN19

JP9

CN20

CN28

CN25

CN14

CN24

Intel

BF-VS MCH

Intel

ESB2

JP5

Intel

BF-VS MCH

Intel

BF-VS MCH

CPU1

CPU0

DIMM 3

CN21

This diagram is representative of the latest board revision available at the time of

publishing. The board you receive may not look exactly like the above diagram.

11

Jumper Legend



OPEN - Jumper OFF, without jumper cover



CLOSED – Jumper ON, with jumper cover

Jumper/Connector Function

JP5 Clear CMOS Jumper

JP9 IPMB Connector

JP16 Video Disable Jumper

CN1/CN3 EPS 12V Power Supply Connector

CN11 COM1 Port

CN12 Floppy Connector

CN13 Keyboard/Mouse Connector

CN14 IDE Connector

CN15/CN25/CN28 USB Header

CN19 Front Panel Header

CN20/CN21 CPU Fan Connectors

CN22/CN23/CN24 Chassis Fan Connectors

CN26 SMDC Connector

CN27 Onboard Video Connector

12

JP16 JP5

JP9

13

JP5: Clear CMOS Jumper

3

1

Normal

(Default)

3

1

Clear

Use this jumper when you forgot your system/setup

password or need to clear system BIOS setting.

How to clear the CMOS data

- Power off system and disconnect power

supply from AC source

- Use jumper cap to close Pin_2 and 3 for

several seconds to Clear CMOS

- Replace jumper cap to close Pin_1 and 2

Reconnect power supply to AC source

Power on system

JP16: Video Disable Jumper

3

1

(Default)

Enable the video function.

3

1

Disable the video function.

JP9: IPMB Connector

1

Pin 1 IPMB

DATA

Pin 2 GND

Pin 3 IPMB

CLK

Pin 4 NC

14

CN15 CN28

CN25

CN26

15

CN15: Front Panel USB2.0 Connector (used alone or with CN28/CN25)

2 1 0

1

9

Signal Pin Pin Signal

USB PWR

1 2

USB PWR

USB_P6_N_FB

3 4

USB_P7_N_FB

USB_P6_FB

5 6

USB_P7_FB

GND

7 8

GND

Key

9 10

GND

Use these headers to connect to the USB devices

via the enclosed USB cable.

CN28: Front Panel USB2.0 Connector (used alone or with CN15/CN25)

2 1 0

1

9

Signal Pin Pin Signal

USB PWR

1 2

USB PWR

USB_P2_N_FB

3 4

USB_P3_N_FB

USB_P2_FB

5 6

USB_P3_FB

GND

7 8

GND

Key

9 10

GND

Use these headers to connect to the USB devices

via the enclosed USB cable.

CN25: Front Panel USB2.0 Connector (used alone or with CN15/CN28)

1

2

9

10

Signal Pin Pin Signal

USB PWR

1 2

USB PWR

USB_P4_N_FB

3 4

USB_P5_N_FB

USB_P4_FB

5 6

USB_P5_FB

GND

7 8

GND

Key

9 10

GND

Use these headers to connect to the USB devices

via the enclosed USB cable.

CN26: SMDC Connector

The SMDC connector allows you to connect with Tyan Server Management

Daughter Card (SMDC). The S5370 supports Tyan SMDC M3291. See

Appendix II for more information on SMDC.

16

CN23 (FAN1): Chassis Fan Connector

12V

Speed Control

GND

Tachometer

Use this header to connect the chassis cooling

fan to your motherboard to keep the system at

optimum performance levels.

CN21

CN20

CN23

CN22

SATA 0/1/2/3/4/5

CN24

CN19

17

CN22/CN24: Chassis Fan Connector

12V

Speed Control

GND

Ta c h o m et e r

Use this header to connect the chassis cooling

fan to your motherboard to keep the system at

optimum performance levels.

CN22: FAN2; CN24: FAN3

CN20 (CPU_FAN1): CPU_FAN Connector

+12

V

Speed Control

GND

Ta chom et e r

Use this header to connect the processor cooling

fan to your motherboard to keep the system at

optimum performance levels.

CN21 (CPU_FAN0): CPU_FAN Connector

Speed Control

GND

Ta c h o m et e r

12V

Speed Control

GND

Ta c h o m et e r

Use this header to connect the processor cooling fan to

your motherboard to keep the system stable and

reliable.

This connector supports the tachometer monitoring and

auto fan speed control.

CN19: Front Panel Header

The Front Panel Header is used to connect some control or signal wires from

motherboard to chassis, such as HDD LED, power LED, power button, and

reset button.

HDDLED+

1 2

PWR LED+

HDDLED-

3 4

PWR LED-

GND

5 6

PWR SW+

Reset SW+

7 8

GND

VCC5

9 10

Warning LED+

NMI

11 12

Warning LED-

5VSB

13 14

key

SMBus Data

15 16

GND

SMBus Clock

17 18

Chassis Intr# (Active Low)

18

SATA0/1/2/3/4/5: Serial ATA RAID Connector

7 GND

6 RXP

5 RXN

4 GND

3 TXN

2 TXP

7

1

1 GND

Connects to the Serial ATA ready drives via the

Serial ATA cable

You may use these six Serial ATA ports to

have the support of RAID 0 and 1 through the

on board Intel ESB2 chipset.

19

2.4 - Tips on Installing Motherboard in Chassis

Before installing your motherboard, make sure your chassis has the

necessary motherboard support studs installed. These studs are usually

metal and are gold in color. Usually, the chassis manufacturer will pre-install

the support studs. If you are unsure of stud placement, simply lay the

motherboard inside the chassis and align the screw holes of the

motherboard to the studs inside the case. If there are any studs missing,

you will know right away since the motherboard will not be able to be

securely installed.

Some chassis’ include plastic studs instead of metal. Although the plastic

studs are usable, TYAN recommends using metal studs with screws that will

fasten the motherboard more securely in place.

Below is a chart detailing what the most common motherboard studs look

like and how they should be installed.

20

2.5 - Installing the Processor(s)

Your Tempest i5000VF S5370 supports the latest processor technologies from

Intel. Check the TYAN website for latest processor support:

http://www.tyan.com

Processor Installation

The processor should be installed carefully. Make sure you are wearing an

antistatic strap and handle the processor as little as possible.

Follow these instructions to install your processor

1. Locate the processor socket on the motherboard and lift the protective

cover off as shown.

WARNING:

This new processor socket

designed by Intel is easy to be

damaged. The processor has to be

installed very carefully to prevent

the contact pins of the socket from

breaking. It is strongly

recommended the processor

installation job to be handled by the

experienced technician.

2. Pull the locking lever out of it’s locked position and let it spring into the

open position.

Page is loading ...

Tyan Tempest i5000V S5370 User manual

This manual is also suitable for

Tyan Tempest i5000V S5370 User manual

Related papers

Other documents