Tyan Tiger i5000XL User manual

http://www.tyan.com

1

Tiger i5000XL

///

S2692

Version 1.0

Copyright

this manual may be reproduced or translated without prior written consent from

TYAN Computer Corp.

Trademark

All registered and unregistered trademarks and company names contained in

this manual are property of their respective owners including, but not limited to

the following.

TYAN, Taro and Tiger i5000XL are trademarks of TYAN Computer Corporation.

AMD, Opteron, and combinations thereof are trademarks of AMD Corporation.

Intel, Xeon, and combinations thereof are trademarks of Intel Corporation.

Nvidia and nForce are trademarks of Nvidia Corporation

Microsoft, Windows are trademarks of Microsoft Corporation.

SuSE,is a trademark of SuSE AG.

Linux is a trademark of Linus Torvalds

IBM, PC, AT, and PS/2 are trademarks of IBM Corporation.

Winbond is a trademark of Winbond Electronics Corporation.

Notice

Information contained in this document is furnished by TYAN Computer

Corporation and has been reviewed for accuracy and reliability prior to printing.

TYAN assumes no liability whatsoever, and disclaims any express or implied

warranty, relating to sale and/or use of TYAN products including liability or

warranties relating to fitness for a particular purpose or merchantability. TYAN

retains the right to make changes to product descriptions and/or specifications

at any time, without notice. In no event will TYAN be held liable for any direct or

indirect, incidental or consequential damage, loss of use, loss of data or other

malady resulting from errors or inaccuracies of information contained in this

document.

http://www.tyan.com

2

Table of Contents

Chapter 1: Introduction

1.1 Congratulations Page 5

1.2 Hardware Specifications Page 5

Chapter 2: Board Installation

2.1 Board Image Page 8

2.2 Block Diagram Page 9

2.3 Board Parts, Jumpers and Connectors Page 10

2.4 Mounting the Motherboard Page 22

2.5 Installing the Memory Page 23

2.6 Installing the Processor and Cooling Fan Page 25

2.7 Attaching Drive Cables Page 27

2.8 Installing Add-In Cards Page 29

2.9 Installing Optional SO-DIMM Modules Page 32

2.10 Connecting External Devices Page 33

2.14 Installing the Power Supply Page 34

2.15 Finishing Up Page 35

Chapter 3: BIOS

3.1 About the BIOS` Page 37

3.2 Main BIOS Setup Page 39

3.3 Main Page 40

3.4 Advanced Page 46

3.5 Security Page 58

3.6 Power Page 59

3.7 Boot Page 60

3.8 Exit Page 61

Chapter 4: SATA/RAID Setup

4.1 BIOS Configuration Page 63

4.2 Installing Serial ATA (SATA) hard disks Page 63

4.3 Adaptec RAID Configuration Utility Page 64

4.4 Manage Array Page 64

4.5 Create Array Page 66

4.6 Add/Delete Hotspare Page 68

4.7 Initialize Drives Page 68

4.8 Disk Utilities Page 70

Chapter 5: Diagnostics

5.1 Beep Codes Page 73

5.2 Flash Utility Page 73

5.3 BIOS Post Code Page 74

Appendix I: SMDC Information

Page 79

Appendix II: How to Make a Driver Diskette

Page 81

Glossary

Page 83

Technical Support

Page 89

http://www.tyan.com

3

Check the box contents!

The retail motherboard package should contain the following:

1 x Tiger i5000XL S2692 motherboard

1 x 34-Pin floppy drive cable

2 x Ultra-DMA-133/100/66/33 IDE cable

1 x Tiger i5000XL S2692 User’s Manual

1 x Tiger i5000XL S2692 Quick Reference Guide

1 x TYAN driver CD

1 x I/O shield

1 x Cable set (9 pin serial and 24 pin parallel)

2 x CEK Spring

1 x Serial ATA power cable

2 x Serial ATA cable

1 x USB2.0 cable

If any of these items are missing, please contact your vendor/dealer for

replacement before continuing with the installation process.

http://www.tyan.com

4

NOTE

http://www.tyan.com

5

Chapter 1: Introduction

1.1 - Congratulations

Congratulations on your purchase of the powerful Dual Intel processor solution,

the Tiger i5000XL S2692. Based on Intel® 5000X Greencreek MCH and Intel®

6321ESB I/O Controller chipsets, the S2692 offers exceptional performance.

Compatible with EPS12V power supplies, the CEB form factor S2692 features

an onboard RealTek ALC888 audio controller, one 10/100/1000 Ethernet port

and SATA/RAID, which provides a versatile solution for your workstation needs.

Remember to visit TYAN’s Website at http://www.tyan.com. There you can find

information on all of TYAN’s products with FAQ’s, online manuals and BIOS

upgrades.

1.2 - Hardware Specifications

Processors

 Dual LGA771 sockets

 Supports up to two Dual-Core Intel®

Xeon® Processors 5000/5100 Series

processors

 1333/1066 MHz FSB

 VRD11.0

Chipset

 Intel® 5000X Greencreek MCH +

Intel® 6321ESB I/O Controller

 Winbond W82627EHF Super I/O

chip

Memory

 Four 240-pin DDR2 FBDIMM sockets

 Four memory channels

 Supports ECC DIMMs

 Maximum of 16/8GB DDR2-533/667

Integrated LAN Controllers

 Intel® 82564 Gilgal Single-Port

GbE – ASF 2.0

 One RJ-45 port with LEDs

Integrated I/O

 One 9-pin 16550 UART serial port

 Eight USB 2.0 ports (four at rear,

four via headers)

 PS/2 mouse and keyboard

connectors

 Six Standard/integrated SATA2

connectors

 One RJ-45 10/100/1000 LAN

ports

 One IDE and one Floppy

connectors

Integrated Serial ATAII (SATA-II)

RAID

 Six (6) SATA-II ports

 3.0 Gb/s per port

 RAID 0, 1, 10 supported

BIOS

 Phoenix TrustedCore BIOS on

8Mbit Flash ROM

 Supports APM 1.2, ACPI 2.0

 Serial Console Redirect

 PXE via Ethernet, USB device

http://www.tyan.com

6

Expansion Slots

 One (1) PCI Express x16 slot with

x16 signal

 One (1) PCI Express x8 slot with x4

signal

 One (1) PCI Express x16 slot with x8

signal

 Two (2) PCI-X 133/100MHz slots

 One (1) PCI 32-bit 33MHz slot

 Total six (6) expansion slots

System Management

 ADT7470 Hardware Monitor

 CPU thermal & voltage monitor

support

 Five (5) fan headers (4-pin

configuration)

Integrated Audio Controller

 HDA link

 RealTek ALC888 controller (High

Definition Audio)

 Line-in, Line-out, Mic-in rear ports

 SPDIF In/Out in rear

 Front panel audio header

 CD-in, Aux headers (4-pin

configuration)

Regulatory

 FCC Class B (DoC)

 European Community CE (DoC)

 BSMI

boot

 PnP, DMI 2.0 WfM 2.0 Power

Management

 User-configurable H/W monitoring

 Auto-configuration of hard disk

types

 Multiple boot options

 48-bit LBA support

Form Factor

 CEB (12” x 10.5”)

 EPS 12V/SSI (24+8 pin) power

connectors

 Stacked PS/2 keyboard and

mouse connectors

 One Serial port

 Stacked USB 2.0 (2)

 Stacked USB 2.0 (2) and RJ-45

(1) connectors

 Stacked Line-in, Line-out, Mic-in

audio connectors

 SPDIF port

Power

 On board dual 4-phase VRM

 EPS 12V (24-pin + 8-pin) power

connectors

http://www.tyan.com

7

Chapter 2: Board Installation

Precautions: The Tiger i5000XL supports SSI, EPS12V type power supplies

(24pin + 8pin) and will not operate with any other types. For proper power

supply installation procedures see page 37.

DO NOT USE ATX 2.x or ATXGES power supplies as they will damage the

board and void your warranty.

How to install our products right… the first time

The first thing you should do is reading this user’s manual. It contains important

information that will make configuration and setup much easier. Here are some

precautions you should take when installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the

antistatic bag. Unplug the power from your computer power supply and

then touch a safely grounded object to release static charge (i.e. power

supply case). For the safest conditions, TYAN recommends wearing a

static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the

board, or flex the board in any way.

(3) Avoid touching the motherboard components, IC chips, connectors,

memory modules, and leads.

(4) Place the motherboard on a grounded antistatic surface or on the

antistatic bag that the board was shipped in.

(5) Inspect the board for damage.

The following pages include details on how to install your motherboard into your

chassis, as well as installing the processor, memory, disk drives and cables.

NOTE

DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN

DAMAGED.

http://www.tyan.com

8

2.1- Board Image

This picture is representative of the latest board revision available at

the time of publishing. The board you receive may or may not look

exactly like the above picture.

The following page includes details on the vital components of this

motherboard.

http://www.tyan.com

9

2.2 - Block Diagram

Tiger i5000XL (S2692) Block Diagram

http://www.tyan.com

10

2.3 - Board Parts, Jumpers and Connectors

JP16

P2

PS/2

KB/MS

USB x 2

COM

RJ45

USB x 2

L-in

L-out

Mic

JP25

CN1

J12

J1 3

CN3

DIMM0

DIMM1

DIMM2

DIMM3

CN21

CPU0

CPU1

CN20

CN22

J11

PCIE x16 Slot (x16)

CN24

P3

JP20

JP23

J7

JP15

JP26

JP18

CN19

JP5

SATA0 SATA1 SATA2 SATA3

SATA4 SATA5

CN15

CN28

FDD

IDE

CN23

JP19

JP27

PCIE x8 Slot (x4)

PCIE x16 Slot (x8)

PCIX 133 Slot

PCI 33 Slot

JP7

JP8

JP6

JP24

JP14

P1

This diagram is representative of the latest board revision available at the time of

publishing. The board you receive may not look exactly like the above diagram.

Jumper Legend



OPEN - Jumper OFF, without jumper cover



CLOSED – Jumper ON, with jumper cover

http://www.tyan.com

11

Jumper/Connector Function

CN20/21/22/23/24 4-pin FAN Connector

J12/J13 LEC/LCD Interface Connector

P2 CD_IN Connector

P3 AUX_IN Connector

J7 Audio Front Panel Connector

J11 PC2004 Power Supply Connector

J16 3-pin Chassis Intrusion Header

CN15/CN28 USB2.0 Connector

JP6/JP7/JP8 CPU Bus Clock Select Jumper

JP5 Clear CMOS Jumper

JP19 BIOS Recovery Jumper

JP20 FWH Write Protect Jumper

JP18 Internal buzzer Enable/Disable Jumper

JP23 LAN Enable/Disable Jumper

JP24 PCIX Frequency Setting Jumper

JP25 PS/2 Wake Up Jumper

JP26 Power for Hardware Monitor

JP27 Reset Signal for Hardware Monitor

JP14/JP15 External Thermal Diode Header

http://www.tyan.com

12

CN21

CN15

CN20CN22

J16

CN28

CN24

CN23

http://www.tyan.com

13

CN15: USB2.0 Connector

10

2

9

1

This is used to connect 2 USB 2.0 ports on USB2.0

connector.

Signal Pin Pin Signal

USBPWR 1 2 USBPWR

USB_2D- 3 4 USB_3D-

USB_2D+ 5 6 USB_3D+

GND 7 8 GND

KEY 9 10 NC

CN20/CN21/CN22/CN22/CN23: 4-pin FAN Connector

Use these headers to connect the cooling fans to the

motherboard to keep the system stable and reliable.

Pin 1 Pin 2 Pin 3 Pin 4

GND +12V Tachometer Fan PWM (speed)

Control

J16: 3-pin Chassis Intrusion Header

1

Pin Signal

1 Detect signal

Low means intruder device pluged.

2 Signal intruder

3 GND

http://www.tyan.com

14

J7

CN19

http://www.tyan.com

15

CN19: Front Panel Header

SMBUS Clock

SMBUS Data

5VSB

Non-mask

Interrupt (NMI)

RESET

Switch

HDD LED-

HDD LED+

17

15

13

11

9

7 5

3

1

18

16

14

12

10 8 6

4 2

NC

GND

Key

Warning LED-

Warning LED+

POWER

Switch

PWR LED-

PWR LED+

The motherboard

provides one front

panel header for

electrical

connection to the

front panel

switches and

LED’s.

J7: Front Panel Audio Connector

10 2

9 1

The front panel audio connector allows you to connect

to the front panel audio. It contains line-out and MIC

signal for front panel.

PIN Signal

1 AUD_MIC_L

2 GND

3 AUD_MIC_R

4 AFP_PRESENT

5 AUD_FP_R

6 MIC_JD

7 F_AUD_DET

8 KEY

9 AUD_FP_L

10 LINE_JD

J11: Power Supply Header (for FSC)

1

It can detect and contoll FSC power supply's FAN

speed.

http://www.tyan.com

16

P1

P3

J12

P2

J13

http://www.tyan.com

17

P2: CD_IN Connector

RGND

L

This is for CD-ROM audio connector.

P3: AUX_IN Connector

RGND

L

AUX_IN is used for input and mixing of MPEG, TV tuner, or

other audio sources.

J12/J13: LED Interface Connector (reserved)

J1

2

30

29

1

2

J13

1

2

13

1

4

J12

Pin Signal Pin Signal

1 GND 2 SPKR_OUT_L

3 SLP_LED+ 4 <KEY>

5 <KEY> 6 GND

7 PWR_LED+_0 8 SPKR_OUT_H

9 PWR_LED+_1 10 NC1

11 GND 12 NC2

13 3.3V 14 <KEY>

15 MSG_LED- 16 NC3

17 <KEY> 18 SCSI_LED-_0

19 3.3V 20 SCSI_LED-_1

21 HD_LED- 22 NC4

23 GND 24 <KEY>

25 PWRBTN_N 26 GND

27 SLPBTN_N 28 GND

29 RESET_N 30 GND

J13 is reserved for FSC only.

J13

Pin Signal Pin

1 LCD_SMBCLK 2 GND

3 LCD_SMBDAT 4 GND

5 KEY 6 LCD_LAN_LNK1000

7 LCD_LAN_ACT_L 8 LCD_LAN_LNK_L

9 LCD_IDE_LED_L 10 LCD_ALERT_L

11 LCD_MSG 12 LCD_SLEEP_L

13 LCD_PWR_ACT_L 14 LCD_VDD

http://www.tyan.com

18

JP8

JP19

JP5

JP7

JP6

JP18

http://www.tyan.com

19

P1: High Definition Audio Header

1

2

1

5

1

6

P1 is a standard HDA header,you can plug

another HDA audio card on it

.

Pin Signal Pin Signal

1 ACZ_BIT_CLK_HDA 2 GND1

3 ACZ_RST_N_HDA 4 DVDD

5 ACZ_SYNC_HDA 6 GND2

7 ACZ_SDOUT_HDA 8 DVDD_CORE

9 ACZ_ADIN_0_HDA 10 +12V

11 FNT_PRT_N_HDA 12 KEY

13 ACZ_SDIN_1_HDA 14 3.3VSBY

15 ACZ_SDIN_2_HDA 16 GND3

JP5: Clear CMOS Jumper

3

1

Default

1

3

Clear

You can reset CMOS settings by using this jumper if

you have lost your system/setup password or need to

clear the system BIOS settings.

Power off the system and set JP5 to (2-3) position, and

then power on the system. The CMOS will be cleared

when the POST screen is visible. Finally shut down the

power and move JP5 to it’s default (1-2) position and

power on the system again.

JP6/JP7/JP8: CPU Bus Clock Select Jumper

3

1

1-2 close: CPU select (Default)

1

3

2-3 close: 0

1

3

2-3 open: 1

JP18: Internal Buzzer Enable/Disable Jumper

1

Close: enable internal buzzer (Default)

1

Open: disable internal buzzer

http://www.tyan.com

20

JP24

JP23

JP25

JP20 JP26

Page is loading ...

Tyan Tiger i5000XL User manual

This manual is also suitable for

Tyan Tiger i5000XL User manual

Related papers

Other documents