Dometic Slide Topper Deluxe And Elite 85-86-87.- User guide

Brand: Dometic

Model: Slide Topper Deluxe And Elite 85-86-87.-

Type: User guide

USA

SERVICE OFFICE

Dometic Corporation

2320 Industrial Parkway

Elkhart, IN 46516

CANADA

Dometic Corporation

46 Zatonski, Unit 3

Brantford, ON N3T 5L8

CANADA

For Service Center

Or Dealer Locations

Please Visit:

www.eDometic.com

ww.RV.com

SLIDE TOPPER™

APPLICATION GUIDE

DELUXE & ELITE MODELS:

85, 86, & 87(XXX)(CC).(XXX)-(C)

SLIDE TOPPER SIZING

A. Slide Out Room And Slide Topper Dimensions

1. Full extension of slide out room MUST NOT exceed 44″. See (FIG. 1).

2. Determine Slide Topper width.

Slide Toppers 198″ or wider REQUIRE a bracket option that includes STEEL extensions; a second anti-

billow stop kit and anti-billow bracket kit (one at each end cap); a cradle kit for center support (of FRTA).

Slide Toppers 360″ or wider may use a second (optional) cradle kit.

The Elite Slide Topper is not available in sizes 198″ or wider.

a. Measure slide out room width. See (FIG. 1).

b. Match Slide Topper fabric width (B) as closely as possible to slide out room width. See (FIG. 1) & (FIG. 2).

Slide Topper fabric should completely cover slide out room. See table for selection guidance.

FIG. 1

Slide Out

Room Width

(Including Flange)

Slide Out

Room

Maximum

Extension

44″

FIG. 2

(A)

(B)

(C)

Nominal Awning Width

FRTA

Nominal

Awning Width

SLIDE OUT ROOM WIDTH

(Including Flange)

(Subtract Value Below

From Nominal Awning Width)

SLIDE TOPPER AWNING WIDTH

(Add/Subtract Value Below

To/From Nominal Awning Width)

(Subtract Value Below

From Nominal Awning Width)

Minimum Maximum (A) Overall (B) Fabric 15 3/8″ Extension

Minimum

18 5/8″ Extension

Minimum

< 150″

Example: 102″

- 10″

92″

- 4 1/4″

97 3/4″

+ 2 7/8″

104 7/8″

- 4 1/2″

97 1/2″

- 14″

88″

- 20 1/2″

81 1/2″

≥ 150″

Example: 162″

- 10 1/2″

151 1/2″

- 4 3/4″

157 1/4″

+ 2 3/8″

164 3/8″

- 5″

157″

- 14 1/2″

147 1/2″

- 21″

141″

REVISION

Form No. 3106883.055 01/13

(Replaces 3106883.048)

(French 3108157.037)

LaGrange, IN 46761

3106883.055

A. Mounting Bracket Selection

1. Determine mounting bracket type. See (FIG. 3), (FIG. 4), & (FIG. 5).

Mounting brackets may be installed on slide out room ange ONLY if it provides solid structural support.

The 3106992.X21# mounting bracket kit will accommodate slide out rooms that project 1/4″ to 1″ beyond RV

wall (when closed). This kit is not for use on slide out rooms that close ush to RV wall.

FIG. 3 Mounting Bracket Kit

3106992.X21#

Awning Rail

Awning

Rail

Extension

5 1/4″ Max.

6″ Min.

7″ Max.

Slide Out Room Flange

(With Edge Protector)

Slide Out Room Flange

Mounting Bracket

3/4″ Mounting Bracket

Slide Out

Projection

(Closed)

1/4″ Min.

1″ Max.

FIG. 4 Mounting Bracket Kit

3106992.X39#, .X54#, & .X96#

Awning Rail

Awning

Rail

Extension

5 1/4″ Max.

6″ Min.

7″ Max.

Slide Out Room Flange

(With Edge Protector)

Slide Out Room Flange

Mounting Bracket

1 1/4″ Mounting Bracket

MOUNTING BRACKETS

FIG. 5 Mounting Bracket Kit

3106992.X47# & .X88#

Awning Rail

Awning

Rail

Extension

3 1/2″

Max.

4″ Min.

5″ Max.

Slide Out Room Flange

(With Edge Protector)

Slide Out Room Flange

Mounting Bracket

1 1/4″

Mounting Bracket

Z-Clip

2. Determine mounting bracket location relating to awning rail and slide out room ange. See (FIG. 3), (FIG. 4), (FIG.

5), (FIG. 6), & (FIG. 7).

If slide out room has extra large anges, it may be necessary to install mounting brackets directly on ange,

but ONLY if it provides solid structural support.

To help accommodate water and debris runoff, awning fabric should have as steep a pitch (slope) as feasible

without exceeding the maximum distance shown between awning rail and mounting bracket. Exceeding the

maximum distance will expose awning fabric to catch wind (causing fabric to billow or tear).

FIG. 6

Mounting Bracket Shown

In Typical Position

(Below Flange)

FIG. 7

Mounting Bracket Shown

Directly On Flange

B. Mounting Bracket Spacer (Optional)

If slide out room ange has special features (large curve, recessed into RV wall, etc.) that will interfere with normal

operation of Slide Topper, a mounting bracket spacer (NOT INCLUDED) must be installed. See (FIG. 8) & (FIG. 9).

FIG. 8

Mounting

Bracket Spacer

Large Curve

In Flange

3/4″ 1 1/4″

3106992.X39#

Bracket

FIG. 9

Mounting

Bracket Spacer

RV Wall

Recessed

Flange

3/4″

1 1/4″ 3106992.X47#

Bracket

MOUNTING BRACKETS

Dometic Slide Topper Deluxe And Elite 85-86-87.- User guide

Dometic Slide Topper Deluxe And Elite 85-86-87.- User guide

Dometic Slide Topper Deluxe And Elite 85-86-87.- User guide

Related papers

Other documents