Marvel MA24RAS2LB Spec sheet

Category
Fridges
Type
Spec sheet

This manual is also suitable for

24 Marvel Low Prole
All Refrigerator
ADA Height
Model # MA24RA****
Dynamic Cooling Technology
delivers rapid cooldown and the
industry’s best temperature stability
Low prole, ADA height allows for universal installation
applications, both commercial and residential
MARVEL Intuit™ Integrated Controls ensure precise temperature
management from 34°F to 42°F
MaxStore
roller-glide clear utility bin provides maximum volume to
effectively store large, bulky or loose items
Tall item storage: Half-width interior shelf and extra door storage
allows for high-clearance vertical storage
Pristine arctic white interior easily wipes clean and efcient white
LED lighting illuminates interior for better viewing
Close Door Assist System
gently and automatically closes door
Panel overlay option features soft-close integrated hinge for a truly
ush t with cabinetry
Audible and visual alarms signal when door is left ajar to protect
food integrity and energy use
Vacation/Sabbath mode conserves energy during times when the
unit is not in use and complies with Star-K requirements
Height adjustment up to 1” with leveling legs
4” black adjustable toe kick
1-year warranty
Storage Capacity
Up to (118) 12-oz cans
Storage Conguration
(1) full-width and (1) half-width cantilevered,
fully adjustable white steel-framed glass shelves
(1) xed white steel-framed glass shelf
Product Dimensions
23 W x 31 H x 25D (including handle)
Finish/Door Options
Black
Stainless Steel
White
Wood Overlay
(Panel Ready)
Certied to meet
ENERGY STAR
®
requirements
Ordering Details
Solid Stainless Steel Door,
Right Hinge
MA24RAS2RS
Solid Stainless Steel Door,
Left Hinge
MA24RAS2LS
Smooth White Door, Right Hinge MA24RAS2RW
Smooth White Door, Left Hinge MA24RAS2LW
Smooth Black Door, Right Hinge MA24RAS2RB
Smooth Black Door, Left Hinge MA24RAS2LB
Solid Panel Overlay Door,
Integrated Right Hinge
MA24RAP3RP
Solid Panel Overlay Door,
Integrated Left Hinge
MA24RAP3LP
No panel installation kit required.
Width 23 ⅞"
Interior Finish White
Capacity Up to 100 12-oz cans
Shelving System Cantilever
Shelf Fronts Stainless Steel
Other Storage MaxStore™ Utility Bin
Interior Lighting 2 White LED Pods
Toe Grill Finish Black
Hinge Classic Hinge
Handle Designer
Control Type Intuit™
Temperature Range 34° - 42° F
Lock NA
Electrical Requirements 120V / 60Hz / 15A
Length of Power Cord 5'
Product Dimensions
23 ⅞" W x 31 " H x 21 ½" D
Depth to Front of Door 23
23
/
32
"
Depth to Handle 25
21
/
32
"
Depth with door at 90° 46
13
/
32
"
Shipping Weight 160 lbs
Finishes SS, B, W, O
Vacation /
Sabbath Mode
Yes
Agency Approvals CSA
ENERGY STAR Certied
Finishes Key
SS = Stainless Steel
B = Black
W = White
O = Overlay
"A"
"B"
"C"
24" Rough-In Dimensions
"A" "B" "C"
24"
(61 cm)
31 3/8" to 32 3/8"
(79.7 to 82.2 cm)
24"
(61 cm)
9
"F"
21
1
2"
(54.6 cm)
* Depth dimension of rough-in opening may vary depend-
ing on each individual installation. To recess entire door "F"
dimension plus 1" (2.5 cm) for thickness of power cord plug
is required.
** Minimum rough-in opening required is to be larger than
the adjusted height of the cabinet.
# A grounded 15 amp dedicated circuit is required. Follow
all local building codes when installing electrical and appli-
ance.
APPLIES TO THE FOLLOWING MARVEL MODELS
ML15BC MA24BC
ML15RA MA24BR
MA24RA
ML24BC
ML24BR
ML24RA
PRODUCT DATA
MODEL
ELECTRICAL
REQUIREMENTS #
PRODUCT
WEIGHT
ML15**(G) or (S) 115V/60Hz/15A
105 lbs
(47.7 kg)
ML15**(P) or (F) 115V/60Hz/15A
105 lbs
(47.7 kg)
ML24**(G) or (S) 115V/60Hz/15A
140 lbs
(63.6 kg)
ML24**(P) or (F) 115V/60Hz/15A
140 lbs
(63.6 kg)
MA24**(G) or (S) 115V/60Hz/15A
140 lbs
(63.6 kg)
MA24**(P) or (F) 115V/60Hz/15A
140 lbs
((63.6 kg)
"D"
"E"
"H"
"J"
"G"
PRODUCT DIMENSIONS
Figure 8
!
WARNING
Floor mount Anti-tip Bracket must be installed for freestand-
ing applications. Not required for built in applications.
“G” “H” “J
25 2132
(65.2 cm)
46 1332
(117.9 cm)
25 1116”
(65.2 cm)
Dynamic Cooling Technology
delivers rapid cool down
and the industry’s best
temperature stability
The distinctive Marvel design features a
thermal-efcient cabinet and door combined
with Dynamic Cooling Technology™ for
superior temperature stability, faster cooling
times and speedy temperature recovery even
with high frequency.
Front
Side
F
r
on
t
Forced
Air Fan
Evaporator
Plate
Return
Air Intake
Front
Side
F
r
t
Forced
Air Fan
Evaporator
Plate
Return
Air Intake
Cabinet Dimensions
"D" "E" "F"
23 7⁄8”
(60.7 cm)
31 1 8” to 32 18”
(79.7 to 82.2 cm)
23 23 32
(60.2 cm)
Overlay Panels
14
!
CAUTION
1
5
32"
(2.9 cm)
Figure 17
Right Hand Hinged Door
24" (61 cm) wide appliance
Figure 18
Right Hand Hinged Door
24" (61 cm) wide appliance
OVERLAY DOOR PANEL INSTALLATION
1" (2.5 cm) diameter
x
1
4" (6 mm) deep
4 places
Clearance
for hinge
at top and
bottom
2"
(5.1 cm)
3
11
16"
(9.4 cm)
1
1
2"
(3.8 cm)
typical
1
4"
(6 mm)
Deep
Hinge side of door
Clearance for
screw head,
4 places
30
11
32"
(77.1 cm)
1
11
16"
(4.3 cm)
23
3
4"
(60.3 cm)
3
1
8"
(7.9 cm)
Top of door
Step 4: Assemble the panel to the door
The preferred method of attaching the panel to the door
is to clamp the panel to the door so it cannot move while
drilling the screw pilot holes. Use bar clamps or "C" clamps
with pads on the clamping surfaces that will not mar the
panel or the door. The custom overlay panel should be
ush with the top of the door and centered along the width
of the door. See Figure 10a. Drill holes through the gasket
extrusion using the 10 holes as pilot holes. Use the drill
size from the chart in Table "C", being careful not to drill
through the front surface of the panel, drill no deeper than
1
2" (12.7 mm) deep. If the overlay panel is thinner than
5
8" (16 mm) thick shorter screws will have to be obtained.
Fasten the panel to the door with the 10 screws provided in
the literature pack. (See Figure 19a). Remove the clamps
and replace the gasket in the gasket extrusion channels of
the door. Some force may be required to seat the gasket
into the channels. Be sure the gasket corners are seated
properly.
Material Type #10 Wood Screw
Hardwood
1
8" (3.2 mm) Diameter. Pilot Hole
Softwood
7
64 (2.8 mm) Diameter. Pilot Hole
Table C
Weight of overlay door panel must not exceed 15
pounds (6.8 kg) for a solid door model or 10 pounds
(4.5 kg) for a glass door model.
3
1
8"
(7.9 cm)
1
3
4"
(4.4 cm)
4
1
8"
(10.5 cm)
1
4" (6 mm)
radius is
permissible
This side
to door
3
1
8"
(7.9 cm)
3
27
32"
(9.8 cm)
1
3
16"
(3 cm)
14"
(35.6 cm)
4
7
8"
(12.4 cm)
For comprehensive installation instructions,
please visit www.marvelrefrigeration.com
18
OVERLAY DOOR PANEL INSTALLATION
Step 4: Assemble the panel to the door
The preferred method of attaching the panel to the door
is to clamp the panel to the door so it cannot move while
drilling the screw pilot holes. Use bar clamps or "C" clamps
with pads on the clamping surfaces that will not mar the
panel or the door. The custom overlay panel should be
ush with the top of the door and centered along the width
of the door. See Figure 12a. Drill holes through the gasket
extrusion using the 10 holes as pilot holes. Use the drill
size from the chart in Table "C", being careful not to drill
through the front surface of the panel, drill no deeper than
1
2" (12.7 mm) deep. If the overlay panel is thinner than
5
8" (16 mm) thick shorter screws will have to be obtained.
Fasten the panel to the door with the 10 screws provided in
the literature pack. (See Figure 22a). Remove the clamps
and replace the gasket in the gasket extrusion channels of
the door. Some force may be required to seat the gasket
into the channels. Be sure the gasket corners are seated
properly.
MODEL
DOOR
DESCRIPTION DIM "A"
ML15RAP*RP Solid, Right Hand
30
11
32" (77.1 cm)
ML15RAP*LP Solid, Left Hand
ML15BCF*RP Glass, Right Hand
ML15BCF*LP Glass, Left Hand
ML15BCP*RP Solid, Right Hand
ML15BCP*LP Solid, Left Hand
ML24RAP*RP Solid, Right Hand
ML24RAP*LP Solid, Left Hand
ML24BRF*RP Glass, Right Hand
ML24BRF*LP Glass, Left Hand
ML24BRP*RP Solid, Right Hand
ML24BRP*LP Solid, Left Hand
MA24BRF*RP
Glass, Right Hand
with Lock
27
23
32" (70.4 cm)
MA24BRF*LP
Glass, Left Hand
with Lock
MA24RAP*RP
Solid, Right Hand
with Lock
MA24RAP*LP
Solid, Left Hand
with Lock
Table C
Table D
Material Type #10 Wood Screw
Hardwood
1
8" (3.2 mm) Diameter. Pilot Hole
Softwood
7
64 (2.8 mm) Diameter. Pilot Hole
18
OVERLAY DOOR PANEL INSTALLATION
Step 4: Assemble the panel to the door
The preferred method of attaching the panel to the door
is to clamp the panel to the door so it cannot move while
drilling the screw pilot holes. Use bar clamps or "C" clamps
with pads on the clamping surfaces that will not mar the
panel or the door. The custom overlay panel should be
ush with the top of the door and centered along the width
of the door. See Figure 12a. Drill holes through the gasket
extrusion using the 10 holes as pilot holes. Use the drill
size from the chart in Table "C", being careful not to drill
through the front surface of the panel, drill no deeper than
1
2" (12.7 mm) deep. If the overlay panel is thinner than
5
8" (16 mm) thick shorter screws will have to be obtained.
Fasten the panel to the door with the 10 screws provided in
the literature pack. (See Figure 22a). Remove the clamps
and replace the gasket in the gasket extrusion channels of
the door. Some force may be required to seat the gasket
into the channels. Be sure the gasket corners are seated
properly.
MODEL
DOOR
DESCRIPTION DIM "A"
ML15RAP*RP Solid, Right Hand
30
11
32" (77.1 cm)
ML15RAP*LP Solid, Left Hand
ML15BCF*RP Glass, Right Hand
ML15BCF*LP Glass, Left Hand
ML15BCP*RP Solid, Right Hand
ML15BCP*LP Solid, Left Hand
ML24RAP*RP Solid, Right Hand
ML24RAP*LP Solid, Left Hand
ML24BRF*RP Glass, Right Hand
ML24BRF*LP Glass, Left Hand
ML24BRP*RP Solid, Right Hand
ML24BRP*LP Solid, Left Hand
MA24BRF*RP
Glass, Right Hand
with Lock
27
23
32" (70.4 cm)
MA24BRF*LP
Glass, Left Hand
with Lock
MA24RAP*RP
Solid, Right Hand
with Lock
MA24RAP*LP
Solid, Left Hand
with Lock
Table C
Table D
Material Type #10 Wood Screw
Hardwood
1
8" (3.2 mm) Diameter. Pilot Hole
Softwood
7
64 (2.8 mm) Diameter. Pilot Hole
15
Step 2: Remove the door gasket
With the door laying on a at surface and starting at a
corner of the door remove the magnetic door gasket from
the interior side of the door, see Figure 12. Set the gasket
aside on a at surface.
There are 10 holes in the gasket retainer extrusions, (3 on
each side and 2 at the top and bottom which are used to
fasten the panel to the front of the door. The screws are
provided in the literature pack along with the door lock,
which is provided on certain models.
Figure 11
Press and hold down this
tab on the wire connec-
tor and pull the connector
apart.
Figure 12
Figure 12a
Overlay panel
ush with top
of door.
Holes in
gasket
retainer.
Magnetic Gasket
remove starting at a
corner, grasp and pull
away from the door.
OVERLAY DOOR PANEL INSTALLATION
Step 3: Cut and drill the overlay panel
Depending on your model cut the overlay door panel to the
dimensions shown in Figures 13 to 20. Also see Table "D"
for the height dimension and door styles. The window cut
out is for glass door models only. If your appliance has a
lock also drill the lock hole in the panel, see Figure 22.
Overlay panel to
be centered on
width of door.
15
Step 2: Remove the door gasket
With the door laying on a at surface and starting at a
corner of the door remove the magnetic door gasket from
the interior side of the door, see Figure 12. Set the gasket
aside on a at surface.
There are 10 holes in the gasket retainer extrusions, (3 on
each side and 2 at the top and bottom which are used to
fasten the panel to the front of the door. The screws are
provided in the literature pack along with the door lock,
which is provided on certain models.
Figure 11
Press and hold down this
tab on the wire connec-
tor and pull the connector
apart.
Figure 12
Figure 12a
Overlay panel
ush with top
of door.
Holes in
gasket
retainer.
Magnetic Gasket
remove starting at a
corner, grasp and pull
away from the door.
OVERLAY DOOR PANEL INSTALLATION
Step 3: Cut and drill the overlay panel
Depending on your model cut the overlay door panel to the
dimensions shown in Figures 13 to 20. Also see Table "D"
for the height dimension and door styles. The window cut
out is for glass door models only. If your appliance has a
lock also drill the lock hole in the panel, see Figure 22.
Overlay panel to
be centered on
width of door.
19
Step 5: Assemble lock parts
Two (2) lock extensions are provided with the lock. Use
the longer extension for
3
4" thick overlay panels and the
shorter one for
5
8" thick overlay panels. Assemble the lock
extension, cam stop washer, spring washer, and set screw
to the lock as shown in Figure 21 and 23.
Install this lock assembly into the lock hole in the overlay
panel and secure with the retaining nut on the back side
with a 15 mm socket and ratchet. Make sure the key slot in
the front of the lock is vertical.
OVERLAY DOOR PANEL INSTALLATION
17
32"
(13.7 mm)
3
1
/2"
(89 mm)
1
2" (13 mm) diameter drill
through door panel, from
other side (see detail
above)
13
16" (20.5 mm)
counter bore,
7
16" (11 mm)
deep.
Hinge side of door
Counter bore
lock hole
on back side.
Step 6: Install lock cam
Attach the lock cam to the back of the lock assembly with
the phillips head screw provided. Orient the lock cam verti-
cally when installing on the lock.
SECTION A-A
SCALE 1 : 1
LOCK
NUT
BRASS EXTENSION
CAM
PHILLIPS SCREW
13/16 COUNTER
BORE 7/16 DEEP
1/2 HOLE
3/4 INCH
WOOD PANEL
SPRING WASHER
INNER
DOOR
Figure 21
Figure 22a
#10 x 1/2"
screw
Figure 22
17
Figure 18
Left Hand Hinged Door
24" (61 cm) wide appliance
!
CAUTION
OVERLAY DOOR PANEL INSTALLATION
Weight of overlay door panel must not
exceed 15 pounds (6.8 kg) for a solid
door model or 10 pounds (4.5 kg) for a
glass door model.
Figure 20
Right Hand Hinged Door
24" (61 cm) wide appliance
23
3
4"
(60.3 cm)
1" (2.5 cm) diameter
x
1
4" (6 mm) deep
4 places
4
7
8"
(12.4 cm)
3
27
32"
(9.8 cm)
1
3
16"
(3 cm)
14"
(35.6 cm)
1
4" (6 mm)
radius is
permissible
3
1
8"
(7.9 cm)
1
3
4"
(4.4 cm)
3
1
8"
(7.9 cm)
3
1
8"
(7.9 cm)
"A"
(See Table D)
2"
(5.1 cm)
3
11
16"
(9.4 cm)
4
1
8"
(10.5 cm)
1
1
2"
(3.8 cm)
typical
1
4"
(6 mm)
Deep
1
11
16"
(4.3 cm)
Hinge side of door
Top of door
Clearance for hinge
at top and bottom
Clearance for hinge
at top and bottom
Clearance for
screw head,
4 places
Figure 17
Left Hand Hinged Door
24" (61 cm) wide appliance
23
3
4"
(60.3 cm)
1" (2.5 cm) diameter
x
1
4" (6 mm) deep
4 places
4
7
8"
(12.4 cm)
3
27
32"
(9.8 cm)
1
3
16"
(3 cm)
14"
(35.6 cm)
1
4" (6 mm)
radius is
permissible
3
1
8"
(7.9 cm)
3
1
8"
(7.9 cm)
3
1
8"
(7.9 cm)
1
3
4"
(4.4 cm)
"A"
(See Table D)
2"
(5.1 cm)
3
11
16"
(9.4 cm)
4
1
8"
(10.5 cm)
1
1
2"
(3.8 cm)
typical
1
4"
(6 mm)
Deep
1
11
16"
(4.3 cm)
Hinge side of door
Top of door
Clearance for
screw head,
4 places
Figure 19
Right Hand Hinged Door
24" (61 cm) wide appliance
This side
facing interior
This side
facing interior
1
5
32"
(2.9 cm)
1
5
32"
(2.9 cm)
17
Figure 18
Left Hand Hinged Door
24" (61 cm) wide appliance
!
CAUTION
OVERLAY DOOR PANEL INSTALLATION
Weight of overlay door panel must not
exceed 15 pounds (6.8 kg) for a solid
door model or 10 pounds (4.5 kg) for a
glass door model.
Figure 20
Right Hand Hinged Door
24" (61 cm) wide appliance
23
3
4"
(60.3 cm)
1" (2.5 cm) diameter
x
1
4" (6 mm) deep
4 places
4
7
8"
(12.4 cm)
3
27
32"
(9.8 cm)
1
3
16"
(3 cm)
14"
(35.6 cm)
1
4" (6 mm)
radius is
permissible
3
1
8"
(7.9 cm)
1
3
4"
(4.4 cm)
3
1
8"
(7.9 cm)
3
1
8"
(7.9 cm)
"A"
(See Table D)
2"
(5.1 cm)
3
11
16"
(9.4 cm)
4
1
8"
(10.5 cm)
1
1
2"
(3.8 cm)
typical
1
4"
(6 mm)
Deep
1
11
16"
(4.3 cm)
Hinge side of door
Top of door
Clearance for hinge
at top and bottom
Clearance for hinge
at top and bottom
Clearance for
screw head,
4 places
Figure 17
Left Hand Hinged Door
24" (61 cm) wide appliance
23
3
4"
(60.3 cm)
1" (2.5 cm) diameter
x
1
4" (6 mm) deep
4 places
4
7
8"
(12.4 cm)
3
27
32"
(9.8 cm)
1
3
16"
(3 cm)
14"
(35.6 cm)
1
4" (6 mm)
radius is
permissible
3
1
8"
(7.9 cm)
3
1
8"
(7.9 cm)
3
1
8"
(7.9 cm)
1
3
4"
(4.4 cm)
"A"
(See Table D)
2"
(5.1 cm)
3
11
16"
(9.4 cm)
4
1
8"
(10.5 cm)
1
1
2"
(3.8 cm)
typical
1
4"
(6 mm)
Deep
1
11
16"
(4.3 cm)
Hinge side of door
Top of door
Clearance for
screw head,
4 places
Figure 19
Right Hand Hinged Door
24" (61 cm) wide appliance
This side
facing interior
This side
facing interior
1
5
32"
(2.9 cm)
1
5
32"
(2.9 cm)
  • Page 1 1
  • Page 2 2
  • Page 3 3

Marvel MA24RAS2LB Spec sheet

Category
Fridges
Type
Spec sheet
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI