2. Golden Lighting
  3. 3071-1P GG

Golden Lighting 3071-1P GG Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Golden Lighting 3071-1P GG Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Assembly Instructions: 3071-1P (Athena)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important
notes above. Shut off the power at the circuit breaker and
completelyremovetheoldxturefromtheceiling,includingthe
oldmountingstrap.
Fromthepartsbagremovethemountingstrapassembly.One
endofnipple(F)shouldbeattachedtomountingstrap(A)with
hexnutandwasher(C&D)inplace.Theotherendshould
havecanopyloop(H)attached.Attachmountingstrap(A)to
thejunctionboxusingmountingscrews(B)andascrewdriver.
Tightensecurely.Unscrewcanopyloopcollar(I)fromcanopy
loop (H). Pass canopy (G) over the mounted canopy loop to
testtheheight.Approximatelyhalfofthecanopyloop’sexterior
threadsshouldbeexposed,andthecanopyloopcollarshould
tsnuglyontothecanopyloop.Removecanopy(G)andadjust
theheightofnipple(F)andcanopyloop(H)untilthedesired
heightisreached.Removecanopy(G)andcanopyloop(H).
ASSEMBLING THE FIXTURE
Bymeasuring,determinethecorrectnumberofchainlinks
neededforproperhangingheight.Ifnecessary,useapairof
plierstoopenandremoveanyexcesschain(J).Attachone
chainconnector(K)toeachendofchain(J).Twistthesidelock
to secure in place. Use one of chain connectors (K) to attach
chain(J)totoploop(L)andclosethechainconnector.Feed
thexture’swiresupthroughthechain(everythreelinksorso),
pullingthewiresuntiltaut.Usethefreechainconnector(K)to
attachchain(J)tocanopyloop(H).Untwistcanopyloopcollar
(I) to allow canopy (G) to be added to the chain. Feed the wires
upthroughthechain.Allowcanopy(G)todropdownontothe
chain/wire.
CONNECTING THE WIRES
Haveanassistantsupportthexture’sweightwhilecompleting
thewiring.Cutawayanyexcesswireaddingatleast8to10
inchesofwiretothedesiredlength.Threadthexture’swires
throughcanopyloop(H)andnipple(F).Attachthexture’swires
tothepowersupplywiresfromthejunctionbox.Connectblack
toblack(orsmooth);whitetowhite(orribbed);groundtoground
(greenorcopper).Twisttheendsofthewirepairstogether,then
twist on a wire connector. Make sure all twists are in the same
direction.Ifthereisnogroundwire(greenorcopper)fromthe
junctionbox,locategroundscrew(E)onmountingstrap(A)and
wrapthexture’sgroundwirearoundthegreengroundscrew
(E).Useascrewdrivertosecuregroundscrew(E)ontothe
mountingbracket.Tuckallwiresneatlyintothejunctionbox.
FINISHING THE INSTALLATION
Pushcanopy(G)uptotheceilingandslidecanopyloopcollar(I)
upbeneaththecanopy.Tightlythreadcanopyloopcollar(I)onto
canopy loop (H) to secure canopy (G) in place.
Installalightbulbinaccordancewiththexture’sspecications.
Donotexceedthemaximumrecommendedwattage.
Your installation is now complete. Turn on the power and test
thexture.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, contact
the place of purchase to arrange
for replacement parts.
L
M
I
G
K
J
K
B
A
E
F
C
D
H
N
/