Assembly Instructions: 3602-M1L (Duncan)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Carefully remove all of the contents from the carton. See the
important notes above. Shut off the power at the circuit breaker
andcompletelyremovetheoldxturefromthewall,including
theoldmountingstrap.
Fromthepartsbagremovethemountingstrapassembly.One
endofnipple(F)shouldbeattachedtomountingstrap(A)with
washerandhexnuts(C,D)inplace.Theotherendshouldhave
canopy loop (H) attached.
Attachmountingstrap(A)tothejunctionboxusingmounting
screws(B)andascrewdriver.Tightensecurely.Unscrewcanopy
loop collar (I) from canopy loop (H). Pass canopy (G) over the
mountedcanopylooptotesttheheight.Approximatelyhalf
ofthecanopyloop’sexteriorthreadsshouldbeexposed,and
thecanopyloopcollarshouldtsnuglyontothecanopyloop.
Removecanopy(G)andadjusttheheightofnipple(F)and
canopyloop(H)untilthedesiredheightisreached.
ASSEMBLING THE FIXTURE
Bymeasuring,determinethecorrectlengthofchainneededfor
properhangingheight.Ifnecessary,useapairofplierstoopen
andremoveanyexcesschain.Attachoneofchainconnectors
(K)tochain(J).Passthexturewiresthroughtoploop(L).Pull
thewiresuntiltaut.Feedthexturewiresupthroughthechain
(everythreelinksorso),pullingthewiresuntiltaut.Usethefree
chain connector (K) to attach chain (J) to canopy loop (H). Slide
canopy loop collar (H) and canopy (G) down onto the chain/
wires. Pull the wires until taut. Trim the wires to the desired
lengthplus8to10inches.
CONNECTING THE WIRES
Haveanassistantsupportthextureweightwhilecompleting
thewiring.Cutawayexcesswire.Threadthexturewires
throughcanopyloop(H)andcanopy(G).Attachthexture’s
wirestothepowersupplywiresfromthejunctionbox.Connect
blacktoblack(orsmooth);whitetowhite(orribbed);ground
toground(greenorcopper).Twisttheendsofthewirepairs
together,thentwistonawireconnector.Makesurealltwistsare
inthesamedirection.Ifthereisnogroundwire(greenorcopper)
fromthejunctionbox,locategroundscrew(E)onmounting
strap(A)andwrapthexturegroundwirearoundthegreen
groundscrew(E).Useascrewdrivertosecuregroundscrew(E)
ontothemountingbracket.Tuckallwiresneatlyintothejunction
box.
FINISHING THE INSTALLATION
Pushcanopy(G)uptotheceilingandslidecanopyloopcollar(I)
upbeneaththecanopy.Tightlythreadcanopyloopcollar(I)onto
canopy loop (H) to secure canopy (G) in place.
Slide shade (N) over socket (M) and secure in place with socket
washer(O)andsocketring(P).
Installlightbulb(notincluded)inaccordancewiththexture’s
specications.Donotexceedthemaximumrecommended
wattage.
Your installation is now complete. Turn on the power and test
thexture.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, contact
the place of purchase to arrange
for replacement parts.
B
A
C
D
E
G
F
H
I
J
K
L
M
N
O