Page is loading ...
Get crafty.
Craft Desk/Table
Craft Collection | Model 5421417
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Teknik
www.teknikoffice.co.uk
Table of Contents Assembly Tools Required
Part Identifi cation
Hardware Identifi cation
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
5-20
21-24
25-28
29-30
31
Skip the power trip.
This time.
Short Screwdriver
Pae 2
Part Identifi cation
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identifi cation to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
E SHELF (2)
F BACK (1)
G LONG BASE MOLDING (2)
H SHORT BASE MOLDING (2)
I BRACE (2)
J RAIL EXTENSION (2)
K LEFT DRAWER SIDE (2)
L DRAWER BACK (2)
M RIGHT DRAWER SIDE (2)
N DRAWER BOTTOM (2)
O DRAWER FRONT (2)
P TOP (1)
A
B
C
P
E
E
F
G
G
H
H
I
I
J
J
K
K
L
L
M
M
N
N
O
O
Pae 3
Hardware Identifi cation
åScrews are shown actual size. You may receive extra hardware with your unit.
HIDDEN CAM - 47
3
CAM COVER CARD - 5
7
(EXTENSION SET SHOWN SEPARATED)
1EXTENSION RAIL - 4 2EXTENSION SLIDE - 4
WOOD DOWEL - 1
5KNOB - 2
6
RIGHT FILE GLIDE - 2
810 ELECTRICAL CORD - 1
SILVER 1/2" FLAT HEAD SCREW - 16
15
SILVER 13/16" PAN HEAD SCREW - 8
14
SILVER 1-3/16" FLAT HEAD SCREW - 8
11 SILVER 1-3/16" PAN HEAD SCREW - 6
12
LEFT FILE GLIDE - 2
9
CAM SCREW - 47
4
Pae 4
16 SILVER 1116" MACHINE SCREW 2 17 1116" PAN HEAD SCREW 8
METAL BRACKET - 4
18 WASHER - 2
19
Step 1
Arrow
3
F
C
B
A
M x 2
I x 2
K x 2
E x 2
Arrow
Arrow
3
Arrow
3
å Push forty-seven HIDDEN CAMS (3) into the ENDS (A
and B), UPRIGHT (C), SHELVES (E), BACK (F), BRACES (I),
LEFT DRAWER SIDES (K and M).
3
Arrow
3
Arrow
3
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
(47 used)
Pae 5
Step 2
4
å
Turn forty-fi ve CAM SCREWS (4) into the ENDS (A and B),
UPRIGHT (C), TOP (P), SHORT BASE MOLDINGS (H), and
DRAWER FRONTS (O).
å
NOTE: Two CAMS SCREWS will be used in step 11.
O x 2
H x 2
P
C
B
A
Pae 6
å Fasten the RAIL EXTENSIONS (J) to the LEFT END (B)
and UPRIGHT (C). Use eiht SILVER 13/16" FLAT HEAD
SCREWS (14).
å Fasten the LONG BASE MOLDINGS (G) to the LEFT
END (B) and UPRIGHT (C). Use six SILVER 1-3/16" PAN
HEAD SCREWS (12).
Step 3
C
B
SILVER 13/16" FLAT HEAD SCREW
(8 used for the EXTENSION RAILS)
14
J
J
Surface with more holes
Surface with more holes
G
G
Curved ede
SILVER 1-3/16" FLAT HEAD SCREW
(6 used for the BASE MOLDINGS)
12
Pae 7
Remember:
Rihty tihty.
Lefty loosey.
Step 4
å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as
shown in the upper diaram below. Be prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (1) to the LEFT END (B) and UPRIGHT (C).
Use eiht SILVER 1/2" FLAT HEAD SCREWS (15).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in
the enlared diaram. Then, slide the inner cartride of the EXTENSION
RAIL in to fi nd the other hole that lines up with the hole in the END and
UPRIGHT. Turn a SCREW into this hole.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
Open end
Open end
Open end
1
1
1
1
C
B
Pae 8
SILVER 1/2" FLAT HEAD SCREW
(8 used in this step)
15
Push up on the black lever and pull the SLIDE from the RAIL.
2
1
å Fasten the SHELVES (E) to the UPRIGHT (C). Tihten six
HIDDEN CAMS.
Step 5
1
2
Pae 9
Surface with HIDDEN CAMS
C
E
E
Surface with
HIDDEN CAMS
å Fasten the BRACES (I) to the UPRIGHT (C). Tihten four
HIDDEN CAMS.
Step 6
1
2
I
I
Surface with HIDDEN CAMS
Pae 10
C
Finished ede
Finished ede
Step 7
1
2
Pae 11
E
E
I
I
B
Short
Screwdriver
å You will need a short screwdriver in this step.
å Fasten the LEFT END (B) to the SHELVES (E) and
BRACES (I). Tihten ten HIDDEN CAMS.
å Fasten the SHORT BASE MOLDINGS (H) to the UPRIGHT (C)
and LEFT END (B). Tihten four HIDDEN CAMS.
Step 8
1
2
B
C
H
H
Flat ede
Flat ede
Pae 12
Side Step: Make
nachos. (Optional, but
recommended.)
Step 9
1
2
Pae 13
F
A
Notch
Surface with
HIDDEN CAMS
These edes must be even.
å Fasten the BACK (F) to the RIGHT END (A). Tihten two
HIDDEN CAMS.
å Stand your unit upriht.
å Turn two CAM SCREWS (4) into the UPRIGHT (C).
å Fasten the BACK (F) to the UPRIGHT (C). Tihten two
HIDDEN CAMS.
Step 10
1
2
F
Surface with
HIDDEN CAMS
4
C
Pae 14
Step 11
Pae 15
å Turn and remove the lare nut from the female end of
the ELECTRICAL CORD (10) as shown to the riht.
å Next thread the male end of the cord throuh the hole in
the RIGHT END (A) as shown below.
å Lastly, turn the lare nut back onto the female end of the
ELECTRICAL CORD (10) as shown below.
å Insert the WOOD DOWEL (5) into the hole in the ede of
the RIGHT END (A).
å Fasten the TOP (P) to the RIGHT END (A), BACK (F),
UPRIGHT (C) and LEFT END (B). Tihten ten HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWEL in the RIGHT END inserts
into the TOP.
A
10
10
Male end of ELECTRIC CORD
Female end of ELECTRIC CORD
12
B
C
F
5
lare nut
P
Step 12
1
2
å
Fasten one each of the DRAWER SIDE (K and M) to a
DRAWER FRONT (O). Tihten four HIDDEN CAMS.
å Slide the DRAWER BOTTOM (N) into the rooves
in the DRAWER
SIDES (K and M) a
nd DRAWER FRONT (O).
Be sure the
DRAWER
BOTTOM inserts
into the DRAWER
BACK roove.
K
K
K
M
M
M
N
N
L
21
O
O
O
Unfi nished surface
Groove
BLACK 1-3/16" FLAT HEAD SCREW
(8 used in this step)
11
å Fasten a DRAWER BACK (L) to the DRAWER SIDES (K and M). Use four BLACK 1-3/16" FLAT HEAD SCREWS (11).
å NOTE: Be sure the DRAWER BOTTOM (N) inserts into the roove of the DRAWER BACK (L).
å Repeat this step for the other drawer.
Pae 16
3
Step 13
Pae 17
å Fasten two EXTENSION SLIDES (2) to the DRAWER SIDES (K and M). Use four SILVER 1/2"FLAT HEAD SCREWS (15).
å Push a LEFT FILE GLIDE (9) onto the top ede of a LEFT DRAWER SIDE (K) and a RIGHT FILE GLIDE (8) onto the top
ede of the RIGHT DRAWER SIDE (M).
å Fasten a KNOB (6) to the DRAWER FRONT (O). Use a SILVER 11/16" MACHINE SCREW (16).
å Repeat this step for the other drawer.
å You have the option to fasten the 421414 Hutch or 421416 Oranizer Hutch to your unit. If you purchased the 421414
Hutch, o to the next step. If you purchased the 421416 Oranizer Hutch, o to Step 15 now. To complete the Craft
Table assembly without Hutch attachment, o to Step 16 now.
K
M
2
2
Use hole #3
K
M
8
9
6
O
SILVER 1/2" FLAT HEAD SCREW
(8 used for the EXTENSION SLIDES)
15
SILVER 11/16" MACHINE SCREW
(2 used in this step)
16
Step 14
Pae 18
å With someone's help, carefully set the 421414 Hutch on to
the TOP (P).
å Fasten four METAL BRACKETS (18) to the holes on the
underside of the TOP (P). Use four 11/16” PAN HEAD
SCREWS (17).
å Fasten the METAL BRACKETS on the TOP (P)
to the 421414 Hutch. Use two WASHERS (19) and four
11/16” PAN HEAD SCREWS (17).
å Go to Step 16 now to complete the Craft Table assembly.
421414 Hutch
19
18
18
19
P
11/16" PAN HEAD SCREW
(8 used in this step)
17
(4 used)
18
Step 15
Pae 19
å With someone's help, carefully set the 421416 Oranizer
Hutch on to the TOP (P).
å Fasten four METAL BRACKETS (18) to the holes on the
underside of the TOP (P). Use four 11/16” PAN HEAD
SCREWS (17).
å Fasten the METAL BRACKETS on the TOP (P)
to the 421416 Oranizer Hutch. Use two WASHERS (19) and
four 11/16” PAN HEAD SCREWS (17).
å Go to the next step to complete the Craft Table assembly.
421416 Oranizer Hutch
11/16" PAN HEAD SCREW
(8 used in this step)
17
18
(4 used)
18
19
P
19
18
Step 16
å Peel a CAM COVER from the CAM COVER CARD (7) and
stick one onto each visible HIDDEN CAM.
å To insert the drawers into your unit, line up the
EXTENSION SLIDES on the drawers with the EXTENSION
RAILS on the unit and push the drawers into the unit until
they are fully inserted. The drawers will push in hard until
it is all the way in, then it will slide in and out easier.
å NOTE: Please read the back paes of the instruction
booklet for important safety information.
å This completes assembly. Clean with your favorite
furniture polish or a damp cloth. Wipe dry.
To cover HIDDEN CAMS
7
Pae 20
60 lbs.
25 lbs.
25 lbs.
35 lbs.
35 lbs.
/
