Heath Zenith 9700LeD User manual

Dated receipt required for warranty replacement.

FEATURES

• Automaticallycomesonwhenmotionisdetected.

• Automaticallyturnslightoff.

• Photocell keeps the light off during daylight

hours.

• LEDindicatesmotionwassensed(dayornight).

REQUIREMENTS

• Thelightcontrolrequires120voltsAC.

• If you want to use Manual Override mode, the

controlmustbewiredthroughaswitch.

NOTICE:Nottobeusedonlightdimmerortimer-

controlledcircuits.

• Some electrical codes require installation by a

qualiﬁed electrician.

• Thisproductisintendedforusewiththeenclosed

gasketandwithajunctionboxmarkedforusein

wetlocations.

• Thislightxturehasbeentested/certiedusing

Lights of America LED Lamp Model Numbers

2003LEDP38-65K, 2002LEDR30-65K, and

2002LEDP30-65K.

UNPACKING

Besuretoremoveallcontentsfrompackagingand

verifyallitemsarepresentbeforeassemblingthislight

xture.Thispackageincludesthefollowingitems:

• SecurityLight

• TwoLEDPAR38lamps

 (LightsofAmericaModel:2003LEDP38-65K)

• Twodecorativelampshells

• MountingStrap

• PlasticHanger

• RubberPlug

• Mountinghardware

• Wirenuts

• Owner’sManual

©2008 598-1360-00

Motion Sensor

Light Control

Model: 9700LED Series

INSTALLATION

Foreasyinstallation,selectanexistinglightwitha

wallswitchforreplacement.

Forbestperformance,mountthextureabout8ft.

(2.4m)abovetheground.NOTE:Ifxtureismounted

higherthan8ft.(2.4m),aimingthesensordownwill

reducecoveragedistance.

For eave mount only:

1. Swingthesensorheadtowardstheclampscrew

joint.

For under eave installation, the sensor head must

be rotatedasshowninthenexttwostepsforproper

operationandtoavoidtheriskofelectricalshock.

Controls

Eave Mount

Wall Mount

ClampScrew

2. Thenrotatethesensorheadclockwise180°so

thecontrolsfacedown.

Ifthesensorpopsoutoftheballjoint,loosenthe

clampscrewandpushthesensorbackintotheball

joint.Tightentheclampscrewwhendone.

2

598-1360-00

WIRING THE LIGHT CONTROL

WARNING: Turn power off at circuit breaker

or fuse.

MOUNT THE LIGHT CONTROL

1. Alignthelightcontrolcoverplateandcoverplate

gasket.Securewiththemountingbolt.

2. Alignthethreeslotsinthedecorativeshellwith

thelampholderpins.Pushtheshellinandthen

twistclockwisetolock.Repeatforothershell.

LockNut

Toavoidwaterdamageandelectricalshock,

keeplampholders30°belowhorizontal.

5. Adjustthelampholdersbylooseningthelock

nutsbutdonotrotatethelampholdersmorethan

180°fromthefactorysetting.Whenscrewingin

theoodlamps,donotovertighten.

Keeplampsat

least1"(25mm)

fromthesensor.

Donotallowthe

lampstoblock

thelens.

Lens

3. Pushtherubberplugrmlyintoplace.

4. Ifa wetlocation junctionbox wasnot used,

caulk the wall plate mounting surface with

siliconeweathersealant.

ShellSlot

1. Removetheexistinglightxture.

2. Installthemountingstrapasshownusingtwo

screwsthattyourjunctionbox.

3. Theplastichangercanbeusedtoholdthexture

whilewiring.Thesmallendoftheplastichanger

canbethreadedthroughtheholeinthecenter

ofthecoverplate.Thesmallendthengoesinto

oneoftheslotsonthemountingstrap.

4. Routethelightcontrol’swiresthroughthelarge

gasketholes.

5. Twistthejunctionboxwiresandxturewiresto-

getherasshown.Securewithwireconnectors.

White to WhiteBlack to Black

Junction box ground wire to green ground screw

on ﬁxture.

Gasket

Mounting

Strap

MountingBolt

RubberPlug

3

598-1360-00

TESTING AND ADJUSTMENTS

1. Turn on the circuit breaker and light switch.

MotionMotion

NOTE: If xture ismountedhigher than 8ft. (2.4

m),aimingthesensordownwill reduce coverage

distance.

The detector is less sensitive to motion directly

towardsit.

Maximum Range Maximum

Coverage Angle

RANGE

1051TEST

ON-TIME

Bottom of Sensor

Avoid aiming the control at:

•Objectsthatchangetemperaturerapidly,suchas

heating vents and air conditioners.Theseheat

sourcescouldcausefalsetriggering.

•Areaswherepets or trafﬁcmaytriggerthecon-

trol.

•Nearby large, light-colored objects reecting

lightmaytriggertheshut-offfeature.Donotpoint

otherlightsatthesensor.

70ft.

(21m)

8ft.

(2.4m)

180°

MIN MAX

Least Sensitive Most Sensitive

Sensor

3. Loosen the clamp screw

inthesensorballjointand

gentlyrotatethesensor.

4. Walkthroughthecoverage

areanotingwhereyouare

whenthelightsturnon(also,

the LED will ash several

times when motion is de-

tected). Move the sensor

headup,down,orsideways

to change the coverage

area. Keep the sensor at

least 1" (2.5 cm) away from

the lamps.

5. AdjusttheRANGEasneed-

ed.RANGEsettoohighmay

increasefalsetriggering.

6. Secure the sensor head

by tightening the clamp

screw. Donot overtighten

thescrew.

7. Set the amount of TIME you want the lights

tostayonaftermotionisdetected(1,5,or10

minutes).

WARNING: Risk of ﬁre. Do not aim the

lamps at a combustible surface within 3 ft.

(1 m).

Clamp

Screw

Ball Joint

Aim Sensor

Down for Short

Coverage

Aim Sensor

Higher for Long

Coverage

Note:Sensorhasa1

1

/

2

minute warm up period

beforeitwilldetectmotion.Whenrstturnedon

wait1

1

/

2

minutes.

2. TurntheRANGEcontroltothemediumposition

(halfwaybetweenMINandMAX)andtheON-

TIMEcontroltotheTESTposition.

4

598-1360-00

Note: Whenrstturnedonwaitabout1

1

/

2

minutes

forthecircuitrytocalibrate.

*resetstoSecuritymodeatdawn.

OPERATION

Mode: On-Time Works: Day Night

Test

5Seconds x x

Security

1,5or10Minutes x

Manual

Override

Until Dawn* x

MANUAL MODE

AUTO

TEST

ON-TIME Switch at 1, 5, or

10 minutes

...backon.

1SecondOFF

then...

ManualOverridemodecanonly

be activated at night when the

ON-TIMEswitchissettothe1,

5,or10minuteposition.

Flipthelightswitchoffforonesec-

ondthenbackontochangefrom

SECURITY mode to MANUAL

OVERRIDEmode.

To return to SECURITY mode,

either:

•turnthelightoffforoneminute

thenturniton,or...

•daylightwillautomaticallyreset

thelighttoSECURITYmode.

MODE SWITCHING SUMMARY

Flip light switch off

for one second then

back on*

*Ifyougetconfusedwhileswitchingmodes,turn

thepoweroffforoneminute,thenbackon.Afterthe

calibrationtimethecontrolwillbeintheSECURITY

mode.

MANUAL OVERRIDE MODE

SECURITY

MODE

SPECIFICATIONS

Range ...........................Upto70ft.(21m)[varieswith

surroundingtemperature].

SensingAngle .............. Upto180°

ElectricalLoad ..............Upto 300WattMaximum

Incandescent [Up to 150

Wattmaximumeachlamp

holder]or10WattMaximum

LED(Upto5WattMaximum

eachlampholder).

BulbType ...................... Up to150Watt Maximum

PA R 3 8  Tu n g s t e n

Incandescentor5WattLED

model2003LEDP38-65K.

PowerRequirements .... 120VAC,60Hz

OperatingModes ..........TEST, SECURITY, and

MANUALOVERRIDE

ON-Timer ......................1,5,10minutes

TestTimer ..................... 5Seconds

Manual

OverrideTimer .............. Until Dawn

Range ...........................Adjustable

5

598-1360-00

TROUBLESHOOTING GUIDE

SYMPTOM POSSIBLE CAUSE SOLUTION

Lights will not come

on.

1. Lightswitchisturnedoff.

2. Lampislooseorburnedout.

3. Fuseisblownorcircuitbreakeristurned

off.

4. Daylightturn-offisineffect.

5. Incorrect circuit wiring, if this is a new

installation.

6. Sensorisnotaimedtowarddesiredcover-

agearea.

1. Turnlightswitchon.

2. Checklampandreplaceifburnedout.

3. Replacefuseorturncircuitbreakeron.

4. Recheckafterdark.

5. Verifywiringiscorrect.

6. Re-aimsensortocoverdesiredarea.

Lights come on in

daylight.

1. Lightcontrolmaybeinstalledinarelatively

darklocation.

2. LightcontrolisinTEST.

1. Thextureisoperatingnormallyunderthese

conditions.

2. Setcontrolswitchto1,5,or10minutes.

Lightscomeonforno

apparentreason.

1. Lightcontrolmaybesensingsmallanimals

orautomobiletrafc.

2. Rangeissettoohigh.

1. ReduceRange.Re-aimsensor.

2. ReduceRange.

Lightsstayon

continuously.

1. Thesensormaybepickingupaheatsource

like an air vent, dryer vent, or brightly

painted,heat-reectivesurface.

2. SensorisinManualOverridemode.

1. ReduceRange.Re-aimsensor.

2. Setcontrolswitchto1,5,or10minutes.

 Followmanualoverrideinstructionstoreset.

Lights ash on and

off.

1. Heatorlightfromthelampsmaybeturning

thelightcontrolonandoff.

2. Heat being reected from other objects

maybeaffectingthesensor.

3. SensorisintheTestmode.

4. Light may be leaking through the ood

lampreectors

1. Repositionthelampsawayfromthesensor.

2. ReduceRange.Re-aimsensor.

3. WhileinTESTmode,lightonlystaysonfor5

seconds.

4. Makesure the metal lamp protectors are in-

stalled.

6

598-1360-00

TWO YEAR LIMITED WARRANTY

Productwillbefreeofdefectduetoworkmanshipforaperiodoftwo(2)years.Ifproductfailswithinthe

statedlife,returndefectiveproducttoretailerofLightsofAmerica.

Warrantytermsandconditionsofretailerapply.

Warrantyandguaranteevoidifproductismisused.

Ifreplacementproductisnotavailableatretailstore,pleasereturnproductintheoriginalpackage,along

withacopyofthedatedsalesreceipt,descriptionoftheproblem,andyournameandreturnaddressto

themanufacturerattheaddresslistedbelow:

LightsofAmerica

611ReyesDrive

Walnut,CA91789

Attn:ConsumerAffairsDept.

Distributedby:

611ReyesDrive

Walnut,California91789

Tel:(800)321-8100/(909)594-7883

Fax:(909)594-6758

Website:www.lightsofamerica.com

Page is loading ...

19

598-1360-00

Notes / Notas __________

______________________

20

598-1360-00

Notes / Notas __________

______________________

Heath Zenith 9700LeD User manual

Heath Zenith 9700LeD User manual

in other languages

Related papers

Other documents