AWSENS SL5662-BZ User manual

Brand
AWSENS
Model
SL5662-BZ
Category
Motion detectors
Type
User manual
© 2012 HeathCo LLC
TEST
Features
• Turnsonlightingwhenmotionisdetected.
• Automaticallyturnslightingoff.
• Photocellkeepsthelightingoffduringdaylighthours.
• LEDindicatesmotionwassensed(dayornight).
TEST 1 5 10
ON-TIME
Put the ON-TIME switch on the
bottomofthesensorintheTEST
position.
OPERATION
*resetstoAutoModeatdawn.
ON-TIME
TEST 1 5 10
...backon.
1Second
OFF then...
PuttheON-TIMEswitchinthe1,5,
or10minuteposition.
Manual mode only works at night
becausedaylightreturnsthesensor
toAUTO.
Flipthelightswitchoffforonesecond
thenbackontotogglebetweenAUTO
andMANUALMODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 10
position.
Note:Whenrstturnedonwaitabout1
1
/
2
minutesfor
thecircuitrytocalibrate.
Thispackageincludes:
LightControl
Requirements
• Thelightcontrolrequires120-voltsAC.
• IfyouwanttouseManualMode,thecontrolmustbe
wiredthroughaswitch.
• Some codes require installation by a
qualified electrician.
• Thisproductisintendedforusewiththeenclosed
gasketandwithajunctionboxmarkedforuseinwet
locations.
Mode: On-Time Works: Day Night
Test
5Seconds x x
Auto
1,5,or10Minutes x
Manual
ToDawn* x
AUTO
MANUAL MODE
PlasticHanger
RubberPlug
Gasket
4Screws
(2sizesincluded)
MountingStrap
MountingBolt
2Wire
Connectors
Motion Activated Security Light
Model SL5462
2
204026-01
INSTALLATION
Foreasyinstallation,selectanexistinglightwithawall
switchforreplacement.
Forbestperformance,mountthextureabout8ft.(2.4m)
abovetheground.
NOTE:
Ifxtureismountedhigherthan
8ft.(2.4m),aimingthesensordownwillreducecoverage
distance.
Foreavemountonly:
❒Swingthesensorheadtowardstheclampscrew
joint.
If thesensorpops out oftheball joint, loosenthe
clampscrewandpushthesensorbackintotheball
joint.Tightentheclampscrewwhendone.
❒Thenrotatethesensorheadclockwise180°sothe
controlsfacedown.
Controls
Wall Mount Eave Mount
For under eave installation, the sensor head must
be rotatedasshowninthenexttwostepsforproper
operationandtoavoidtheriskofelectricalshock.
Controls
Controls
ClampScrew
Move ON-TIME Switch to
1, 5, or 10 minutes
Mode Switching Summary
Flip light switch off
for one second then
back on*
MANUAL MODE
AUTO
TEST
* Ifyougetconfusedwhileswitchingmodes,turnthe
poweroffforoneminute,thenbackon.Afterthecali-
brationtimethecontrolwillbeintheAUTOmode.
3
204026-01
1. Removetheexistinglightxture.
2. Installthemountingstrapasshownusingtwoscrews
thattyourjunctionbox.
3. Theplastichangercanbeusedtoholdthexture
whilewiring.Thesmallendoftheplastichanger
canbethreadedthroughtheholeinthecenterof
thecoverplate.Thesmallendthengoesintoone
oftheslotsonthemountingstrap.
4. Route the light control’s wires through the large
gasketholes.
5. Twistthejunctionboxwiresandxturewirestogether
asshown.Securewithwireconnectors.
Wire the Light Control
WARNING: Turn power off at circuit breaker
or fuse.
4
204026-01
180°
70ft.
(21m)
8ft.
(2.4m)
Maximum Range Maximum
Coverage Angle
NOTE:Ifxtureismountedhigherthan8ft.(2.4m),aim-
ingthesensordownwillreducecoveragedistance.
Thedetectorislesssensitivetomotiondirectlytowardsit.
3. Loosentheclampscrewinthe
sensor ball joint and gently
rotatethesensor.
4. Walk through the coverage
area noting where you are
whenthelightsturnon(also,
theLEDwillashseveraltimes
whenmotionisdetected).Move
thesensorheadup,down,or
sidewaystochangethecover-
agearea.Keep the sensor at
least 1" (25 mm) away from
the bulbs.
5. AdjusttheRANGEasneeded.
RANGE set too high may
increasefalsetriggering.
6. Secure the sensor head by
tightening the clamp screw.
Donotovertightenthescrew.
7. SettheamountofON-TIMEyouwantthelightsto
stayonaftermotionisdetected(1,5,or10minutes).
NOTE: It is recommended to use the10minute
ON-TIMEsettingwhenusingCFLbulbs.
Bottom of Sensor
Avoid aiming the control at:
•Objects that change temperature rapidly, such as
heating vents and air conditioners.These heat
sourcescouldcausefalsetriggering.
•Areaswherepets or trafficmaytriggerthecontrol.
•Nearby large, light-colored objectsreectinglight
maytriggertheshut-offfeature.Donotpointother
lightsatthesensor.
Clamp
Screw
Ball
Joint
Aim Sensor
Down for Short
Coverage
Aim Sensor
Higher for Long
Coverage
Least Sensitive Most Sensitive
WARNING: Risk of fire. Do not aim the bulbs
at a combustible surface within 3 ft. (1 m).
TEST AND ADJUSTMENT
1. Turn on the circuit breaker and light switch.
NOTE: Sensor has a 1
1
/
2
minute warm up period
beforeitwilldetectmotion.Whenrstturned
on,wait1
1
/
2
minutes.
2. Turn the RANGE controltothe medium position
(halfwaybetweenMINandMAX)andtheON-TIME
controltotheTESTposition.
Motion Motion
Sensor
RANGE
1051TEST
ON-TIME
MIN MAX
IMPORTANT:DonotleaveON-TIMEswitchinthe
TESTposition.ThefrequentON/OFFcyclingofthe
bulbwillreduceitslife.
5
204026-01
SYMPTOM POSSIBLE CAUSE SOLUTION
Lights will not come
on.
1. Lightswitchisturnedoff.
2. Floodlampislooseorburnedout.
3. Fuseisblownorcircuitbreakeristurnedoff.
4. Daylightturn-offisineffect.
5. Incorrectcircuitwiring,ifthisisanewinstallation.
6. Lightcontrolaimedinwrongdirection.
1. Turnlightswitchon.
2. Checkoodlampandreplaceifburnedout.
3. Replacefuseorturncircuitbreakeron.
4. Recheckafterdark.
5. Verifywiringiscorrect.
6. Re-aimlightcontroltocoverdesiredarea.
Lightscomeoninday-
light.
1. Light control may beinstalled in a relatively dark
location.
2. LightcontrolisinTEST.
1. Thextureisoperatingnormallyunderthesecondi-
tions.
2. Setcontrolswitchto1,5,or10minutes.
Lights come on for no
apparentreason.
1. Lightcontrolmaybesensingsmallanimalsorauto-
mobiletrafc.
2. Rangeissettoohigh.
1. Re-aimlightcontrol.
2. Reducerange.
Lightsturnofftoolatein
Dusk-to-Dawnsetting.
Lightcontrolmaybeinstalledinarelativelydarkloca-
tion.
Relocatelightcontrol,oruse3houror6hoursetting.
Lightsstayoncontinu-
ously.
1. Aoodlampispositionedtooclosetothelightcontrol
orpointedatnearbyobjectsthatcauseheattotrigger
thelightcontrol.
2. Thelightcontrolmaybepickingupaheatsource
likeanairvent,dryervent,orbrightlypainted,heat-
reectivesurface.
3. Lightcontrolisinmanualmode.
1. Repositiontheoodlampawayfromthelightcontrol
ornearbyobjects.
2. Reducerange.
3. SwitchlightcontroltoAUTO.
Lightsashonandoff. 1. Heatorlightfromtheoodlampsmaybeturningthe
lightcontrolonandoff.
2. Heatbeingreectedfromotherobjectsmaybeturn-
ingthelightcontrolonandoff.
3. LightcontrolisintheTESTmodeandwarmingup.
4. Lightmaybeleakingthroughtheoodlampreec-
tors.
1. Repositiontheoodlampawayfromthelightcon-
trol.
2. Repositionlightcontrol.
3. Flashingisnormalundertheseconditions.
4. ReplacetheoodlampswithnewhighqualityPAR
38lamps.(Makesurethemetallampprotectorsare
installed).
Lightsashonce,then
stay off in manual
mode.
Lightcontrolisdetectingitsownlights. Reposition ood lampsto keep area belowthe light
controlrelativelydark.
SPECIFICATIONS
TROUBLESHOOTING GUIDE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

AWSENS SL5662-BZ User manual

Brand
AWSENS
Model
SL5662-BZ
Category
Motion detectors
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents