2. Home
  3. Home security & automation
  4. Motion detectors
  5. Heath Zenith
  6. 9600LED series

Heath Zenith 9600LED series User manual

  • Hello! I am an AI chatbot trained to assist you with the Heath Zenith 9600LED series User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Dated receipt required for warranty replacement.
FEATURES
• Automaticallycomesonwhenmotionisdetected.
• Automaticallyturnslightoff.
• Photocell keeps the light off during daylight
hours.
REQUIREMENTS
• Thelightcontrolrequires120voltsAC.
• If you want to use Manual Override mode, the
controlmustbewiredthroughaswitch.
NOTICE:Nottobeusedonlightdimmerortimer-
controlledcircuits.
• Some electrical codes require installation by a
qualified electrician.
• This light xture has been tested/certied us-
ing Lights of America LED Lamp Model No.
2025LEDE12.
UNPACKING
Besuretoremoveallcontentsfrompackagingand
verifyallitemsarepresentbeforeassemblingthislight
xture.Thispackageincludesthefollowingitems:
• Lantern
• ThreeLEDLamps
(LightsofAmericaModel:2025LEDE12)
• Universalmountingbracket(X-Bar)
• Mountinghardware
• Wirenuts
• Owner’sManual
©2008 598-1338-03
Motion Sensing
Diecast Metal Lantern
Model: 9600LED Series
INSTALLATION
Forbestperformance,mountthextureabout6feet
(1.8m)abovetheground.
1. Removetwodecorativenuts.
2. RemoveX-Bar.
3. TightenmountingscrewsonX-Barngertight.
4. AttachX-Bartojunctionbox.
JunctionBox
X-Bar
DecorativeNut
LanternBase
LanternMounting
Screw
X-Bar
BracketMounting
Screw
Note:Werecommendhavinganassistanthelphold
thelanternassemblyduringthewiringprocess.
2
598-1338-03
WIRING
One Motion Light
Two Motion Lights
Recommended Grounding Method
Useagreenground“pigtail”(notprovided)and
twistoneendtogetherwiththebarexturewire
andtheboxgroundwire.Securewithawirecon-
nector.Securetheotherendofthe“pigtail”with
theGNDscrewontheX-bar.
CAUTION: DO NOT connect the RED wire
unless you want to control other lights from
the motion sensor (see Optional Wiring).
Black to black
White to white
Note:Allwiringshouldberuninaccordancewiththe
NationalElectricalCodethroughconduitoranother
acceptablemeans.Contact a qualified electrician
if there is any question as to the suitability of
the system.
WARNING: Turn power off at circuit breaker
or fuse.
Ifyouhavemetaljunctionbox,youmaynotneedthe
green“pigtail”.Ifyouareunsureaboutthegrounding
method,consultyourlocalbuildingcode.
Connectthexturewirestothewiresinthejunction
box.Twistthewirestogetherandsecurewithwire
connectors.
Black
White
Greenor
Bare
Light
Fixture
Black
White
Greenor
Bare
Light
Fixture
Light
Fixture
3
598-1338-03
Black
White
Greenor
Bare
Light
Fixture
Light
Fixture
(Standard)
Master Slave
Black
White
Greenor
Bare
Light
Fixture
Light
Fixture
Red
Red
OPTIONAL WIRING
Thisxtureisprovidedwithasensorratedfor360Watts.Sincethextureisonlyrated180Watts,180Watts
ofadditionallightingmaybecontrolledbythissensor.
Whendeterminingwhataxtureisratedfor,donotsimplylookattheratingonthelampinthexture.Look
atthemarkingwhichspeciesthemaximumlampwattageforwhichthextureissuitable.
Onceyouhaveselectedthexturestobeconnectedanddeterminedtheirmaximumratings,addtheserat-
ingsup.Forinstance,ifyouhave3xturesrated180Watts,100Watts,and75Wattsrespectively,youhave
atotalloadof355Watts.
Wiring Diagram 1 – When wiring to control a standard light fixture:Stripthemotionsensor’sredwire
andconnecttothestandardlight’sblackwire.Connectallwhitewirestogether.Totalxtureratingsmustnot
exceed360Watts(3.0A).
Wiring Diagram 2 – When wiring to control another motion sensing light fixture (Master / Slave): Strip
theredwireinbothlightxtures.Connecttheredwireofthecontrolling(master)xturetotheredandblack
wiresofthecontrolled(slave)xture.Connectallwhitewirestogether.Totalxtureratingsmustnotexceed
360Watts(3.0A).
Wiring Diagram 3 – When wiring so either motion light turns on the both motion lights (Master / Master):
Striptheredwireinbothlightxtures.Connecttheredwireofonexturetotheredwireofthesecondxture.
Note:Inmostinstallations,anadditionalwire(samegageasexistinghousewire)willhavetobeinstalledin
thehousetoconnectthetwoxturesasmaster/master.Connectallwhitewirestogetherandallblackwires
together.Totalxtureratingsmustnotexceed360Watts(3.0A).
Wiring Diagram 1 Wiring Diagram 2
Wiring Diagram 3
Master
Black
White
Red
Green
or Bare
Master
Light
Fixture
Light
Fixture
4
598-1338-03
FINAL ASSEMBLY
1. Pushthewiresintothejunctionbox.Makesure
noneofthewiresgetpinched.
2.
Slidethextureassemblyontothemountingscrews.
Tightendecorativenutsremovedinstep1ofInstal-
lationsectionsecurelyagainstxturebase.
JunctionBox
MountingScrew
DecorativeNut
3. Caulkaroundxturebasewithsiliconeweather
sealant.
4. InstallthethreeLEDLamps(LightsofAmerica
Model No. 2025LEDE12 included). Note:This
xture’sE12candelabrabaseuseseitherLED
Lamps(1.5Wmaximumeach) or tungsten in-
candescentType“B”bulbs(60Wattmaximum
each).
5. Insertthreadedrodofnialthroughtopcover.Slide
starwasherontorodandthreadthenutontothe
rod.Tightensecurely.
6. Place top cover onto xture and attach using
thetwodecorativenuts(included).Handtighten
only.
TopCover
DecorativeNut
3LightBulbs
(60Watt
Maximumeach)
Fixture
Assembly
Finial
StarWasher
Nut
5
598-1338-03
TESTING AND ADJUSTMENTS
1. Turn on the circuit breaker and light switch.
Note:Sensorhasa1
1
/
2
minute warm up period
beforeitwilldetectmotion.Whenrstturnedon
wait1
1
/
2
minutes.
2. Set:
ON-TIMEswitchtoTEST
SENSITIVITYdialtoMidway
3.
Walkthroughthecoverageareanotingwhereyou
arewhenthelightsturnon.InTESTmode,light
willstayonfor5secondsaftersensingmotionand
thenturnoff.
4. AdjusttheSENSITIVITYtoincreaseordecrease
therangeasneeded.Toomuchsensitivitymay
causefalsetriggeringduetoheatsourcesinthe
coveragearea(seeAdjustment of Coverage Area
or Troubleshootingsection).
5. SettheamountofON-TIMEyouwantthelightto
stayonaftermotionisdetected(5or10minutes)
or...
SettheON-TIMEtotheDUSK-to-DAWNsetting
ifyouwantthelighttostayonallnight,every
night.Thephotocellwillturnthelightoffduring
theday.
Maximum Range Maximum
Coverage Angle*
(Top View)
TEST 5
10
DUSK
MINUTES TO DAWN
– +
SEN
30ft.
(9.1m)
6ft.
(1.8m)
180°
Photocell
Least Sensitive Most Sensitive
The sensor is less sensitive to motion directly
towards it and more sensitive to motion across
coveragearea.
Sensor
Motion Motion
6
598-1338-03
Note: Whenrstturnedonwaitabout1
1
/
2
minutes
forthecircuitrytocalibrate.
*resetstoSecuritymodeatdawn.
OPERATION
Mode: On-Time Works: Day Night
Test
5Seconds x x
Security
5or10Minutes x
Automatic
Override
Dusk-to-Dawn x
Manual
Override
UntilDawn* x
MANUAL MODE
AUTO
TEST
ON-TIME Switch at 5 or 10
minutes
...backon.
1SecondOFF
then...
ManualOverridemodecanonly
be activated at night when the
ON-TIMEswitchissetto the5
or10minuteposition.
Flipthelightswitchoffforonesec-
ondthenbackontochangefrom
SECURITY mode to MANUAL
OVERRIDEmode.
To return to SECURITY mode,
either:
•turnthelightoffforoneminute
thenturniton,or...
•daylightwillautomaticallyreset
thelighttoSECURITYmode.
MODE SWITCHING SUMMARY
Flip light switch off
for one second then
back on*
*Ifyougetconfusedwhileswitchingmodes,turn
thepoweroffforoneminute,thenbackon.Afterthe
calibrationtimethecontrolwillbeintheSECURITY
mode.
MANUAL OVERRIDE MODE
ADJUSTMENT OF COVERAGE AREA
Thesensoronthislightxturedetects“motion”bythe
movementofheatacrossthecoveragearea.However,
followingareexamplesofobjectsthatalsoproduce
heatandcancausethesensortotrigger:
•PoolsofWater •AirConditioners
•DryerVents •Animals
•HeatingVents •AutomobileTrafc
Ifyoususpectthataheatsourceofthistypeistrig-
geringthesensor,reducethesensitivity.
SPECIFICATIONS
Range ...........................Upto30ft.(9.1m)[varies
withsurroundingtempera-
ture].
SensingAngle .............. 180°
ElectricalLoad ..............Up to 180WattMaximum
Tungsten Incandescent
or 5 Watt Maximum LED
(Lights of America model
2025LEDE12).
BulbType ......................E12 Candelabra Base,
Type“B”,60WattMaximum
Tungsten Incandescent or
LEDmodel2025LEDE12
1.5Watt.
SensorCapacity ...........360Watt(3.0A)Maximum
TungstenIncandescent
PowerRequirements .... 120VAC,60Hz
OperatingModes ..........TEST, SECURITY, AUTO-
MATIC OVERRIDE and
MANUALOVERRIDE
ON-Timer ......................5or10minutes
TestTimer .....................5Seconds
Automatic
OverrideTimer ..............Dusk-to-Dawn
Manual
OverrideTimer ..............UntilDawn
SECURITY
MODE
7
598-1338-03
TROUBLESHOOTING GUIDE
SYMPTOM POSSIBLE CAUSE SOLUTION
Lights will not come
on.
1. Lightswitchisturnedoff.
2. Lampislooseorburnedout.
3. Fuseisblownorcircuitbreakeristurned
off.
4. Daylightturn-offisineffect.
5. Incorrect circuit wiring, if this is a new
installation.
1. Turnlightswitchon.
2. Checklampandreplaceifburnedout.
3. Replacefuseorturncircuitbreakeron.
4. Recheckafterdark.
5. Verifywiringiscorrect.
Lights come on in
daylight.
1. Lightcontrolmaybeinstalledinarelatively
darklocation.
2. LightcontrolisinTEST.
1. Thextureisoperatingnormallyunderthese
conditions.
2. Setcontrolswitchto5or10minutesorDusk-to-
Dawn.
Lightscomeonforno
apparentreason.
Lightcontrolmaybesensingsmallanimalsor
automobiletrafc.
Reducesensitivity.
Lightsstayoncontinu-
ously.
1. Thesensormaybepickingupaheatsource
like an air vent, dryer vent, or brightly
painted,heat-reectivesurface.
2. SensorisinAutomaticOverrideorManual
Overridemode.
1. Reducesensitivity.
2. Setcontrolswitchto5or10minutes.
Lights ash on and
off.
1. Heat being reected from other objects
maybeaffectingthesensor.
2. SensorisintheTestmode.
1. Reducesensitivity.
2. WhileinTESTmode,lightonlystaysonfor5
seconds.
Lightdoesnotstayon
inManualmode.
Nearbylarge,light-coloredobjectsreecting
lightmaytriggertheshut-offfeature.
Donotpointotherlightsatthesensor.
8
598-1338-03
TWO YEAR LIMITED WARRANTY
Productwillbefreeofdefectduetoworkmanshipforaperiodoftwo(2)years.Ifproductfailswithinthe
statedlife,returndefectiveproducttoretailerofLightsofAmerica.
Warrantytermsandconditionsofretailerapply.
Warrantyandguaranteevoidifproductismisused.
Ifreplacementproductisnotavailableatretailstore,pleasereturnproductintheoriginalpackage,along
withacopyofthedatedsalesreceipt,descriptionoftheproblem,andyournameandreturnaddressto
themanufacturerattheaddresslistedbelow:
LightsofAmerica
611ReyesDrive
Walnut,CA91789
Attn:ConsumerAffairsDept.
Distributedby:
611ReyesDrive
Walnut,California91789
Tel:(800)321-8100/(909)594-7883
Fax:(909)594-6758
Website:www.lightsofamerica.com
/