Rosewill RISE ATX Full Tower User manual

User’s Manual

1

User ManualRISE

CASE

Contents

Disassemble Chart P.2

P.3

Accessory Box

Installation Guide

Product Overview

Appendix A/B

Opening Chassis

P.4

P.10

A. Liquid Cooler Reference Guide

P.11

B. How to remove the POP out dust filter ( front & top)

P.12

Installing Power Supply

P.4

Installing Motherboard

P.5

P.7Installing External 5.25" Device

P.7Installing External 3.5" Device

P.7~P.9Installing 3.5”/2.5” HDD/SSD

Closing Chassis

P.9

Fan Power Board

P.6

Installing Add On Card

Right side panel

Top dust filter

Top panel

2x 2.5” HDD/SSD trays

5.25” to 3.5” adapter

2

User ManualRISE

CASE

Disassemble Chart

USB3.0 CONNECTOR

USB2.0 CONNECTOR HD AUDIO CONNECTOR

AC97 CONNECTOR

( Please refer to your motherboard’s user’s manual to connect.)

Rear 140mm fan

Left side panel

PSU dust filter

Expansion

slot cover

Front 3x 120mm fans

Front dust filter

2.5”/3.5” HDD trays

2.5”/3.5” HDD/SSD mount

(RISE GLOW ONLY)

Front panel

3

User ManualRISE

CASE

Accessory Box

Figure

Part’s Name

Qty

Function

Screw-A

21

Motherboard/

3.5” HDD

Screw-B

(Rise Glow only)

16

3.5” HDD

Screw-C

8

PSU

Screw-D

2.5” HDD/ ODD

28

Nut Setter

1

Standoff

Installation

Cable Tie

3

Cables/Wires

4

1.

2.

User ManualRISE

CASE

Unscrew to remove left and right panels.

Place the power supply from the left side into

the chassis and secure with screws.

NOTICE :

-If your power supply is equipped with single

fan (120mm, 135mm or 140mm), please have

the fan face to the bottom.

-Please remember to clean the PSU dust

filter regularly or insufficient air intake may

fail your power supply permanently.

**Unscrew to remove the cover to install the

secondary PSU if necessary.

5

3.

User ManualRISE

CASE

-Place the motherboard onto stand-offs and secure with screws.

Micro-ATX

ATX

E-ATX

Motherboard Compatibility

6

4.

User ManualRISE

CASE

-Unscrew to remove expansion slot cover.

-Secure with thumb screw.

C

A

-Install the add-on card into its position.

B

7

5.

6.

User ManualRISE

CASE

- Pull from the bottom to remove the front panel.

- Confirm which bay(s) you want to install device(s),

and then remove the drive bay cover.

- Reinstall the front panel

back into position.

- Put the external 3.5” device

onto the 5.25” to 3.5”

adapter then secure with

screws

- Insert external 5.25” & 3.5”

devices into position then

secure with screws.

*Screw A

8

7.

User ManualRISE

CASE

- Unscrew the screws to remove the

HDD/SSD mount.

*Screw B

- Reinstall the HDD/SSD mount into

position.

- Unscrew the screws to

remove the HDD/SSD

mount cover.

- Screw the 3.5”/2.5”

HDD/SSD onto the

mount, and reinstall the

cover back to the mount.

(RISE GLOW ONLY)

9

8.

9.

User ManualRISE

CASE

- Put the 2.5” HDD/SSD onto the trays

and secure with screws.

- Place the 2.5 HDD trays into position

and secure with screws.

*Screw B

Get power from your power supply

- Connect power supply’s molex 4-pin

connector to this connector.

Deliver power to your fan

- Connect fan’s 3-pin connector to this connector.

10

User ManualRISE

CASE

10.

Make sure all necessary cables and wires

are connected, then reinstall side panels

and secure with screws.

11

User ManualRISE

CASE

Appendix A : Liquid Cooler Reference Guide

Please remove both top and

front panels and install the

liquid cooler into position.

Note : Please refer to the water cooler’s installation manual for proper installation.

REAR FRONT

TOP

120

140

120

140

240

280

120 | 140

240 | 280

360

12

User ManualRISE

CASE

Push down on the highlighted spots simultaneously

to unlatch the dust filter for removal.

A click sound can be heard.

Push down on the highlighted spots simultaneously

to latch in the dust filter when maintenance is complete.

A click sound can be heard.

By default, the pop out dust filter doors are locked

down by one thumb screws to prevent damage in

transportation. The thumb screws will first need to be

removed before the dust filter doors can be easily

popped in and out. Should you prefer to disable the

pop out feature, simply leave the thumb screw in

place.

Remove the Front and then the Top panel of the case.

Locate the thumb screw and twist counterclockwise to

remove.

RISE Glow_V4

Technical Support Information

[email protected] 1-800-575-9885

----------------------------------------------------------------------------------

Thank you for purchasing a quality Rosewill product.

Please register your product at www.rosewill.com

for complete warranty information and support for your product.

Rosewill RISE ATX Full Tower User manual

This manual is also suitable for

Rosewill RISE ATX Full Tower User manual

Related papers

Other documents