Design Ideas 3419342 User manual

MeshWorks

®

shelving

Parts List

Mesh Shelf

(A) x3

Top Pole Section

(B) x4

Bottom Pole Section

(C) x4

Threaded Insert

(D) x4

Leveling Foot

(J) x6

Shelf Clip

(E) 14 clips (28 pieces)

Hook Rack

(F)

Clothing Rod Hook

(I) x2

Plastic Cap

(K) x4

! Do not throw away packaging materials until assembly is complete.

! To clean, wipe with a soft, dry cloth. Spot clean with a damp cloth if needed.

Scan here to watch the

instructional video.

Clothing Rod

(H)

Step 1

Bottom pole section (C)

does not have groove.

Bottom pole section (C)

Leveling Foot (J)

Attach all 4 top pole sections (B) to all 4 bottom pole sections (C) using the threaded inserts (D). Screw a leveling foot (J) into the

bottom of each pole.

Pole (B & C)

Assembly

Step 2

Once poles are assembled, select the groove (spaced in 1” increments) where you’d like your lowest shelf to rest.

Position the two halves of your shelf clip (E) so that the beveled edge is facing the top. Snap the clip together around the

pole and adjust until you feel it locate the groove. Once clips are snapped into place at equal heights on each of the 4

poles, slide a shelf down from the top to rest on the clips. Gently tap with a rubber mallet if needed to secure shelf.

Repeat with additional clips to add a second shelf.

Shelf Clip (E) Assembly

If having difficulties getting the shelf

into place, use a rubber mallet. Use

only a rubber mallet to avoid damage.

The designs, images, artwork, product descriptions and data shown in this document are protected by U.S. and foreign patent, copyright, trade dress and contract law and may not be copied, imitated,

duplicated or used in any manner other than as herein proposed. Design Ideas oers these materials to viewer solely for the purpose of allowing viewer to reference assembly or care instructions for the

depicted products purchased from Design Ideas. By viewing them, viewer agrees to this restriction and not to any other use of same whatsoever. Any other use or further distribution of the shown designs,

images, artwork, text and/or data by viewer or further recipients of same is strictly forbidden. Design Ideas, Ltd. will enforce its intellectual property rights in this material to the fullest extent of the law.

A

Shelf Clip (E) Assembly

If having difficulties getting the rack

into place, use a rubber mallet. Use

only a rubber mallet to avoid damage.

The designs, images, artwork, product descriptions and data shown in this document are protected by U.S. and foreign patent, copyright, trade dress and contract law and may not be copied, imitated,

duplicated or used in any manner other than as herein proposed. Design Ideas oers these materials to viewer solely for the purpose of allowing viewer to reference assembly or care instructions for the

depicted products purchased from Design Ideas. By viewing them, viewer agrees to this restriction and not to any other use of same whatsoever. Any other use or further distribution of the shown designs,

images, artwork, text and/or data by viewer or further recipients of same is strictly forbidden. Design Ideas, Ltd. will enforce its intellectual property rights in this material to the fullest extent of the law.

E

Step 3

Once you have 2 shelves in place, select the height at which you would like the hook rack (F) to rest. Position the two

halves of your shelf clip (E) so that the beveled edge is facing the top. Snap the clip together around the pole and adjust

until you feel it locate the groove. Once clips are snapped into place at equal heights on the front and back pole, slide

the hook rack down from the top to rest on the clips. Gently tap with a rubber mallet if needed to secure the hook rack.

Step 4

Once poles are assembled, select the groove (spaced in 1” increments) where you’d like your top shelf to rest. Position

the two halves of your shelf clip (E) so that the beveled edge is facing the top. Snap the clip together around the pole and

adjust until you feel it locate the groove. Once clips are snapped into place at equal heights on each of the 4 poles, slide

a shelf down from the top to rest on the clips. Gently tap with a rubber mallet if needed to secure shelf.

Shelf Clip (E) Assembly

If having difficulties getting the shelf

into place, use a rubber mallet. Use

only a rubber mallet to avoid damage.

E

A

E

Step 6

With the unit fully assembled, press a plastic cap (F) into the hole in the top of each pole. To level your assembled unit,

adjust the feet by twisting to the desired height.

The designs, images, artwork, product descriptions and data shown in this document are protected by U.S. and foreign patent, copyright, trade dress and contract law and may not be copied, imitated,

duplicated or used in any manner other than as herein proposed. Design Ideas oers these materials to viewer solely for the purpose of allowing viewer to reference assembly or care instructions for the

depicted products purchased from Design Ideas. By viewing them, viewer agrees to this restriction and not to any other use of same whatsoever. Any other use or further distribution of the shown designs,

images, artwork, text and/or data by viewer or further recipients of same is strictly forbidden. Design Ideas, Ltd. will enforce its intellectual property rights in this material to the fullest extent of the law.

Step 5

Place a hook on each side of the shelf. Using a leveling foot (J), attach clothing rod (H) to the clothing rod hooks (I) until the

assembled clothing rod sits firmly in place.

Hook the clothing rod

hook onto the side of the

shelf.

Line up the end of the

clothing rod with the hole

in the hook.

Secure the two together

by screwing a leveling

foot (J) through the hook