Design Ideas 3419334 User manual

MeshWorks

®

shelving

Parts List

Mesh Shelf

(A) x4

Grid

(B)

Top Pole Section

(C) x4

Bottom Pole Section

(D) x4

Threaded Insert

(F) x4

Plastic Cap

(H) x4

Leveling Foot

(E) x4

Shelf Clip

(G) 18 clips (36 pieces)

Utility Grid Hook

(I) x5

! Do not throw away packaging materials until assembly is complete.

! To clean, wipe with a soft, dry cloth. Spot clean with a damp cloth if needed.

Scan here to watch the

instructional video.

Step 1

Bottom pole section (D)

does not have groove.

Bottom pole section (D)

Leveling Foot (E)

Attach all 4 top pole sections (C) to all 4 bottom pole sections (D) using the threaded inserts (F). Screw a leveling foot (E) into the

bottom of each pole.

Pole (C & D)

Assembly

Step 2

Once poles are assembled, select the groove (spaced in 1” increments) where you’d like your lowest shelf to rest.

Position the two halves of your shelf clip (G) so that the beveled edge is facing the top. Snap the clip together around the

pole and adjust until you feel it locate the groove. Once clips are snapped into place at equal heights on each of the 4

poles, slide a shelf (A) down from the top to rest on the clips. Gently tap with a rubber mallet if needed to secure shelf.

Repeat these steps with two more shelves.

Shelf Clip (G) Assembly

If having difficulties getting the shelf

into place, use a rubber mallet. Use

only a rubber mallet to avoid damage.

The designs, images, artwork, product descriptions and data shown in this document are protected by U.S. and foreign patent, copyright, trade dress and contract law and may not be copied, imitated,

duplicated or used in any manner other than as herein proposed. Design Ideas oers these materials to viewer solely for the purpose of allowing viewer to reference assembly or care instructions for the

depicted products purchased from Design Ideas. By viewing them, viewer agrees to this restriction and not to any other use of same whatsoever. Any other use or further distribution of the shown designs,

images, artwork, text and/or data by viewer or further recipients of same is strictly forbidden. Design Ideas, Ltd. will enforce its intellectual property rights in this material to the fullest extent of the law.

G

A

G

B

Step 3

Once the shelves are in place, attach shelf clips (G) at equal heights on the back poles where you'd like your grid to hang.

Slide the grid down from the top of the back two poles. Tap gently from the top with a rubber mallet to secure, if needed.

Step 4

Install clips and top shelf following the steps listed in Step 2.

The designs, images, artwork, product descriptions and data shown in this document are protected by U.S. and foreign patent, copyright, trade dress and contract law and may not be copied, imitated,

duplicated or used in any manner other than as herein proposed. Design Ideas oers these materials to viewer solely for the purpose of allowing viewer to reference assembly or care instructions for the

depicted products purchased from Design Ideas. By viewing them, viewer agrees to this restriction and not to any other use of same whatsoever. Any other use or further distribution of the shown designs,

images, artwork, text and/or data by viewer or further recipients of same is strictly forbidden. Design Ideas, Ltd. will enforce its intellectual property rights in this material to the fullest extent of the law.

G

A

Step 5

With the unit fully assembled, press a plastic cap (H) into the hole in the top of each pole. To level your assembled unit,

adjust the feet by twisting to the desired height.

Step 6

To add a Utility Grid Hook (I), hold the hook so that the widest part is at the bottom. Hook the short arm under the bottom wire

where you'd like the hook to rest (1.), then tilt the hook towards the grid over a top wire (2.) and pull downward to secure (3.).

The designs, images, artwork, product descriptions and data shown in this document are protected by U.S. and foreign patent, copyright, trade dress and contract law and may not be copied, imitated,

duplicated or used in any manner other than as herein proposed. Design Ideas oers these materials to viewer solely for the purpose of allowing viewer to reference assembly or care instructions for the

depicted products purchased from Design Ideas. By viewing them, viewer agrees to this restriction and not to any other use of same whatsoever. Any other use or further distribution of the shown designs,

images, artwork, text and/or data by viewer or further recipients of same is strictly forbidden. Design Ideas, Ltd. will enforce its intellectual property rights in this material to the fullest extent of the law.

1. 2. 3.

Design Ideas 3419334 User manual

Design Ideas 3419334 User manual

Related papers

Other documents