Design Ideas 3419329 User manual

MeshWorks

®

shelving

Parts List

Mesh Shelf

(A) x3

Mesh Half Shelf

(B)

Top Pole Section

(C) x2

Bottom Pole Section

(D) x2

Short Front Poles-35 3/8” long

(E) x2

Threaded Insert

(G) x2

Hook Rack

(F)

Leveling Foot

(J) x4

Shelf Clip

(H) 16 clips (32 pieces)

Wood Top

(K)

Plastic Cap

(I) x4

Scan here to watch the

instructional video.

! Do not throw away packaging materials

until assembly is complete.

! To clean, wipe with a soft, dry cloth.

Spot clean with a damp cloth if needed

Step 2

Once poles are assembled, select the groove (spaced in 1” increments) where you’d like your lowest shelf to rest. Position the two

halves of your shelf clip (H) so that the beveled edge is facing the top. Snap the clip together around the pole and adjust until you

feel it locate the groove. Once clips are snapped into place at equal heights on each of the 4 poles, slide a shelf down from the top

to rest on the clips. Gently tap with a rubber mallet if needed to secure shelf. Repeat with additional clips and shelves, working to

add a second and third shelf.

Step 1

Bottom pole section (D)

does not have groove.

Bottom pole section (D)

Leveling Foot (J)

Attach the 2 top pole sections (C) to the 2 bottom pole sections (D) using the threaded inserts (G). Screw a leveling foot (J) into the

bottom of each assembled pole and into the bottom of each shorter front pole (E).

Pole (C & D)

Assembly

The designs, images, artwork, product descriptions and data shown in this document are protected by U.S. and foreign patent, copyright, trade dress and contract law and may not be copied, imitated,

duplicated or used in any manner other than as herein proposed. Design Ideas oers these materials to viewer solely for the purpose of allowing viewer to reference assembly or care instructions for the

depicted products purchased from Design Ideas. By viewing them, viewer agrees to this restriction and not to any other use of same whatsoever. Any other use or further distribution of the shown designs,

images, artwork, text and/or data by viewer or further recipients of same is strictly forbidden. Design Ideas, Ltd. will enforce its intellectual property rights in this material to the fullest extent of the law.

H

A

Shelf Clip (H) Assembly

If having difficulties getting the shelf

into place, use a rubber mallet. Use

only a rubber mallet to avoid damage.

Step 4

With the hook rack in place, you can add your half shelf to the top of your rack. Position the two halves of shelf clip (E) so

that the beveled edge is facing the top. Snap the clip together around the pole and adjust until you feel it locate the

groove. Once clips are snapped into place at equal heights at the top of your two back poles, slide your half shelf down

from the top to rest on the clips. Gently tap with a rubber mallet if needed to secure shelf.

H

B

Shelf Clip (H) Assembly

If having difficulties getting the shelf

into place, use a rubber mallet. Use

only a rubber mallet to avoid damage.

Step 3

Once the shelves are in place, select the groove (spaced in 1” increments) where you’d like the hook rack (F) to rest. Position the

two halves of your shelf clip (H) so that the beveled edge is facing the top. Snap the clip together around the pole and adjust until

you feel it locate the groove. Once clips are snapped into place at equal heights on each of the 2 back poles, slide the hook rack

down from the top to rest on the clips. Gently tap with a rubber mallet if needed to secure rack.

The designs, images, artwork, product descriptions and data shown in this document are protected by U.S. and foreign patent, copyright, trade dress and contract law and may not be copied, imitated,

duplicated or used in any manner other than as herein proposed. Design Ideas oers these materials to viewer solely for the purpose of allowing viewer to reference assembly or care instructions for the

depicted products purchased from Design Ideas. By viewing them, viewer agrees to this restriction and not to any other use of same whatsoever. Any other use or further distribution of the shown designs,

images, artwork, text and/or data by viewer or further recipients of same is strictly forbidden. Design Ideas, Ltd. will enforce its intellectual property rights in this material to the fullest extent of the law.

H

F

Shelf Clip (H) Assembly

If having difficulties getting the rack

into place, use a rubber mallet. Use

only a rubber mallet to avoid damage.

Step 5

To add the wood top (K), simply rest it on top of the shelf. To clean, you may wipe with a clean, damp cloth.

Step 6

With the unit fully assembled, press a plastic cap (I) into the hole in the top of each pole. To level your assembled unit,

adjust the feet by twisting to the desired height.

The designs, images, artwork, product descriptions and data shown in this document are protected by U.S. and foreign patent, copyright, trade dress and contract law and may not be copied, imitated,

duplicated or used in any manner other than as herein proposed. Design Ideas oers these materials to viewer solely for the purpose of allowing viewer to reference assembly or care instructions for the

depicted products purchased from Design Ideas. By viewing them, viewer agrees to this restriction and not to any other use of same whatsoever. Any other use or further distribution of the shown designs,

images, artwork, text and/or data by viewer or further recipients of same is strictly forbidden. Design Ideas, Ltd. will enforce its intellectual property rights in this material to the fullest extent of the law.

Design Ideas 3419329 User manual

Design Ideas 3419329 User manual

Related papers

Other documents