IS-52274-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
4) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, then thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector aer following the above steps. Never connect
ground wire to black or white power supply wires.
5) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
6) Push xture to wall carefully passing threaded pipe
through hole in canopy[F]. NOTE: Fixture can be
mounted with glass in the up or down posion. Make
sure all wires are inside canopy and do not get pinched
between wall and canopy of xture.
7) Thread lockup knob[G], lockwasher[K], and hexnut[J]
onto mounng pipe and ghten to secure xture to wall.
8) Carefully place the glass[I] over the socket to the xture.
Slip the smaller opening over the socket and t the glass
against the socket.
9) Thread the socket ring[H] onto the socket. Tighten
socket ring to secure glass in place. (DO NOT over
ghten.)
10) Install the recommended bulb (not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
CLEANING:
Always be certain that electric current is turned o before
cleaning.
• Only a so damp cloth should be used. Harsh cleaning
products may damage the nish.
Installaon Instrucons
1) Take threaded pipe[A] from parts bag and screw on the
hexnut[C] as shown.
2) Screw threaded pipe into mounng strap[B]. Mounng
strap must be posioned with extruded thread faced into
outlet box[E]. Threaded pipe must protrude out the back
of mounng strap.
3) Connect mounng strap[B] to outlet box using the strap
mounng screws[D].
Installaon Instrucons (connued)
[A] Threaded
Pipe
[B] Mounting
Strap
[C] Hexnut
[D] Strap
Mounting
Screws
[E] Outlet Box
[F] Canopy
[G] Lockup Knob
[H] Socket Ring
[I] Glass
[J] Hexnut
[K] Lockwasher
E
D
B
A
C
G
I
H
J
K
F
Page is loading ...
Page is loading ...
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Kichler Lighting 45892NI User manual
-
Kichler Lighting 44170BK User manual
-
Kichler Lighting 52231BK User manual
-
Kichler Lighting 49986DBK User manual
-
Kichler Lighting 52275NI User manual
-
Kichler Lighting 44022NBR User manual
-
Kichler Lighting 52029BK User manual
-
Kichler Lighting 52009BK User manual
-
Kichler Lighting 49879BK User manual
-
Kichler Lighting 52224FXG User manual
