2. Kichler Lighting
  3. 44170BK

Kichler Lighting 44170BK User manual

  • Hello! I am an AI chatbot trained to assist you with the Kichler Lighting 44170BK User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
IS-44170-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
4) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, then thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector aer following the above steps. Never connect
ground wire to black or white power supply wires.
5) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
6) Push xture to wall carefully passing threaded pipe with
holes in canopy[H]. Make sure all wires are inside canopy
and do not get pinched between wall and canopy of
xture.
7) Thread lockup knob[I] onto mounng pipe and ghten to
secure xture to wall.
8) Install the recommended bulb (not supplied).
9) Lower the metal frame[F] down over the bulb to the
main body and secure into place using two (2) screws[G]
as shown.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
1) Take threaded pipe[A] from parts bag and screw in screw
on the hexnut[C] as shown.
2) Screw threaded pipe into mounng strap[B]. Mounng
strap must be posioned with extruded thread faced into
outlet box[E]. Threaded pipe must protrude out the back
of mounng strap.
3) Connect mounng strap[B] to outlet box using the strap
mounng screws[D].
Installaon Instrucons (connued)
[A] Threaded
Pipe
[B] Mounting
Strap
[C] Hexnut
[D] Strap
Mounting
Screws
[E] Outlet Box
[F] Metal Frame
[G] Screws
[H] Canopy
[I] Lockup Knob
E
D
B
A
C
F
G
H
I
Page is loading ...
IS-44170-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
4) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, then thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector aer following the above steps. Never connect
ground wire to black or white power supply wires.
5) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
6) Push xture to wall carefully passing threaded pipe with
holes in canopy[H]. Make sure all wires are inside canopy
and do not get pinched between wall and canopy of
xture.
7) Thread lockup knob[I] onto mounng pipe and ghten to
secure xture to wall.
8) Install the recommended bulb (not supplied).
9) Lower the metal frame[F] down over the bulb to the
main body and secure into place using two (2) screws[G]
as shown.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
1) Take threaded pipe[A] from parts bag and screw in screw
on the hexnut[C] as shown.
2) Screw threaded pipe into mounng strap[B]. Mounng
strap must be posioned with extruded thread faced into
outlet box[E]. Threaded pipe must protrude out the back
of mounng strap.
3) Connect mounng strap[B] to outlet box using the strap
mounng screws[D].
Installaon Instrucons (connued)
[A] Threaded
Pipe
[B] Mounting
Strap
[C] Hexnut
[D] Strap
Mounting
Screws
[E] Outlet Box
[F] Metal Frame
[G] Screws
[H] Canopy
[I] Lockup Knob
E
D
B
A
C
F
G
H
I
Page is loading ...
/