12 FT × 12 FT
STEEL BEAM GAZEBO
MODEL #TPGAZ2009
1
A
D
R2
J2
C
C1
E
B
D
R1
S2
S1
P1
L
K
F
G
PACKAGE CONTENTS
J1
M
N
O
Q
P
DESCRIPTION
PART PART
A
B
C
C1
D
E
F
G
1
4
4
8
4
4
4
4
4
1
1
4
4
80
1
1
1
4
4
4
4
PART PART
DESCRIPTION DESCRIPTION
QUANTITY QUANTITY
J1
J2
L
M
N
O
P
P1
Q
R1
R2
S1
S2
Decoration Ball
Small Center Connector
Large Center Connector
Hook
Small Top Bar
Long Top Bar
Connector
Short Top Bar
Left Long Bar
Right Long Bar
Mosquito Net Pipe
Post
Base Plate
Cover
Connector
Hang Ring
Corner Connector
Large Roof
Small Roof
Mosquito Net
Sidewall
2
M6 × 15 mm
Qty. 48
M6 × 32 mm
Qty. 8
M6 × 15 mm
Qty. 4
Wrench
Wrench
Qty. 2
M6 × 15 mm
Qty. 8
T U
V
W
Y ZX II
Stake
Qty. 16
Qty. 1
HARDWARE CONTENTS (shown actual size)
allenandroth.com
3
U
X
Wrench
KEEP ALL FLAME AND HEAT AWAY FROM THIS TENT FABRIC.
A
M
O
O
N
U
N
U
Please read and understand this entire manual before attempting to assemble or install the product.
Two to four people are need for assembly.
Maximum load for the roof hook: 50 lbs.
SAFETY INFORMATION
WARNING:
CAUTION
PREPARTION
INSTALLATION INSTRUCTIONS
Hardware Used
This tent meets the flammability requirements of CPAI-84. The fabric may burn if left in continuous
contact with any flame source. The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.
Do not leave outside during high winds, heavy rains or snow. If high winds, heavy rains or snow
occurs, remove canopy and mosquito net, clear snow load from roof tube, and check for damage
before continued use.
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble
the product.
Estimated Assembly Time: 2-3 hours
Tools Required for Assembly (not included): Ladder
Tools Required for Assembly ( included): Wrench
1. Insert the post plate cover (O) into the post (M). Fix
the base plate (N) underneath the post (M). Insert two
M6*15 mm bolts (U), supporting the post (M) and
secure to the base plate (N) using the wrench (X), but
do not overtighten.
Slide the post plate cover (O) down into place.
Repeat this step for remaining supporting posts (M)
the base plate (N) and the post plate cuvers (O).
M6 x 15 mm Bolt
allenandroth.com
1
4
INSTALLATION INSTRUCTIONS
Hardware Used
2. Insert the right long bar (J2) into the left long bar
(J1). Secure together using M6*15 mm bolt (T).
Repeat the procedure for the other right long bar
(J2) and the left long bar (J1).
Tighten securely with the wrench (X).
allenandroth.com
2
2
J2
J2
J1
J1
M6 × 15 mm
T
X
Wrench
T
T
M6
×
15mm Bolt
U
F
X Wrench
Hardware Used
3. Secure the crossbar (J1/J2)assemblies to the
post (M) using M6*15 mm bolts (U).
Tighten securely with the wrench (X)
Note: Ensure the crossbar assemblies are
installed in the correct positions.The side with
curtain/netting hooks of the crossbar should
keep toward inside.
3
M
M
M
M
M
J1
J1
J2
J2
J2
J2
J2
J2
J1
J1
J1
M
U
U
5
INSTALLATION INSTRUCTIONS
allenandroth.com
4
P
U
U
L
L
Q
W
L
U
U
L
J1
J2
J2
J1
P
P
P
P
Q
Q
Q
Q
L
L
L
L
L
J1
J1
J2
J2
J1
J1
M6
×
15mm BoltU
M6
×
15mm Bolt
W
X Wrench
Y Wrench
Hardware Used
J2
J2
L L
L
4. Fix the corner connector (Q ) and
the post (M) together by the screw
M6*15mm (W).
Fix the mosquito net pipe (L) and
connector (P) to the bars (J1/J2) by
the screw M6*15mm (U).
Tighten securely with the wrench (X).
4
F
5. Insert each connector (F) into each
long top bar (E).
F
A
E
5
6. Screw the hook (C1) into the large
center connector (C) and twist
counterclockwise to tighten.
C
C1
6
M6
×
32mm Bolt
V
X Wrench
Hardware Used
6
INSTALLATION INSTRUCTIONS
allenandroth.com
G
E
G
H
E
E
E
F
V
Q
Q
Q
Q
Q
C
F
F
F
E
E
E
E
J1
J1
J2
J2
J2
J2
J1
J1
4
7
7.Insert the long top bar (E) into the
large center connector (C), connect
the connector pipe (F) with the long
top bar (E), then fix the connector
pipe (F) and the corner connector
(Q) together by the screw
M6*32mm (V).
Tighten securely with the wrench(X).
M6
×
32mm Bolt
V
X Wrench
Hardware Used
V
F
E
J1
P
J1
J2
J2
J2
J2
J2
J1
J1
J1
H
G
E
G
E
E
E
E
E
F
F
C
E
G
G
P
P
P
G
P
G
G
G
P
4
8
8.
Insert the short top bar (G) into the
large center connector (C), then fix
the short top bar (G) with the
connector (P) with the
screw M6*32mm(V).
V
Tighten securely with the wrench(X).
INSTALLATION INST RUCTIONS
7
allenandroth.com
7
allenandroth.com
9. Insert each small top bar (D) into the small
center connector (B). Attach the small roof
(R2) on the small top bar (D), then secure
with the decoration ball (A).
B
D
D
O
R2
A
B
R2
O
O
R2
D
9
10
O
O
R1
F
G
R1
10.
Put the large roof (R1) on the top bar shaft.
8
INSTALLATION INSTRUCTIONS
allenandroth.com
E
D
11
11.
Connect the small top bar (D) with the
large top bar (E).
1
2
12.
Hang the mosquito net (S1) onto inside
of the mosquito net pole, hang the
sidewall (S2) onto outside of the
mosquito net pole, as shown.
S2
S1
4
12
Z
X
Hardware Used
9
INSTALLATION INSTRUCTIONS
allenandroth.com
13. Move the cover (O) upward, fix the base
plate (N) by the stake (Z), then move the
cover (O) down.
Stake
O
N
Z
M
4
13
/
