Anova LBRMING Installation guide

Anova
Brand
Anova
Model
LBRMING
Type
Installation guide

This manual is also suitable for

Anova LBRMING is a traditional bike rack designed for outdoor use. It is made of reinforced concrete and is rated at a 3,000 psi minimum. The bike rack is designed to be installed below the frost line to prevent shifting. It has a 10" depth and a 5" diameter. The bike rack is easy to install and comes with all the necessary hardware. It is a great way to keep your bikes organized and secure.

Anova LBRMING is a traditional bike rack designed for outdoor use. It is made of reinforced concrete and is rated at a 3,000 psi minimum. The bike rack is designed to be installed below the frost line to prevent shifting. It has a 10" depth and a 5" diameter. The bike rack is easy to install and comes with all the necessary hardware. It is a great way to keep your bikes organized and secure.

anovafurnishings.com
888.535.5005 tel
Installation Instructions
Traditional (LBR) ING Bike Racks
TOOLS NEEDED:
Step-by-Step Installation Sequence
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the bike rack.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
Optional: Digging Iron
Shovel
Level
Tamper
Installation Instructions
Step-by-Step Installation Sequence
06/11/2019 Copyright 2019 ANOVA® Manufactured in the U.S.
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
1.
5. Check the concrete manufacturer's specications to see how long the
concrete needs to dry before attempting the use of the installation.
2.
3.
4.
Using a shovel place approximately six inches of gravel into the hole then
tamp it down with a tamper. Repeat this step one more time so there is a total
of 6" of gravel.
NOTE: When digging the hole it is recommended that it has a slight angle and
increases in size the farther down it goes. This helps prevent frost upheaval.
Mix the concrete in a wheel barrel to the manufacturer's specications.
NOTE: We recommend seeking out a local contractor for the best option on
how to pour the concrete. Image 4 shows an example of how the concrete
could be poured.
Pour the concrete based on your local recommendation.
Dig out the holes or a slot for the posts using a shovel and a digging iron. The
holes or slot should be 10" in depth (Double check spec sheet, found online)
and should be a minimum of 5" in diameter. The depth of the hole or slot
should be below the frost line to prevent shiing.
1 2
CAUTION: Call your local utility companies to mark where there are any
cables or pipelines before digging any holes.
Frost Line
4
Frost Line
NOTE: Make sure that concrete is poured below frost line
NOTE: Distances between posts vary depending on models , double check
spec sheets (Found online) to nd the distances needed when digging holes
or slots for posts.
Traditional (LBR) ING Bike Racks
  • Page 1 1
  • Page 2 2

Anova LBRMING Installation guide

Anova
Brand
Anova
Model
LBRMING
Type
Installation guide
This manual is also suitable for

Anova LBRMING is a traditional bike rack designed for outdoor use. It is made of reinforced concrete and is rated at a 3,000 psi minimum. The bike rack is designed to be installed below the frost line to prevent shifting. It has a 10" depth and a 5" diameter. The bike rack is easy to install and comes with all the necessary hardware. It is a great way to keep your bikes organized and secure.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents