LSC Lighting Systems (Aust) Pty Ltd. Page 1
monoPAK Single channel portable dimme
r
monoPAK Sin
g
le channel portable dimmermonoPAK Sin
g
le channel portable dimme
r
monoPAK Single channel portable dimmer
Introduction
IntroductionIntroduction
Introduction
The monoPAK has been designed incorporating many of the high quality components used
on LSC’s 12 channel dimmer family such as high rise time toroidal inductors; 40 Amp Triacs;
60mm-travel low profile fader with integral dust cover; safety HRC fuse holder and 10Amp
ceramic fuse; all enclosed in a solid 1.6mm folded metal housing.
The monoPAK comes complete with a 1.6 metre power input cable and a 0.3m long output
cable with socket. For overseas users, the plugs can be cut-off and fitted with the required
plug and socket combination.
Power input cable
1600mm long Load output cable
300mm long
Input supply fuse
10A HRC M205
t
y
pe
Power on
indicator
60mm Fader with
dust cover
MonoPAK Dimme
r
MonoPAK DimmerMonoPAK Dimme
r
MonoPAK Dimmer
Keyhole
mounting slot
Keyhole
mounting slot
LSC Lighting Systems (Aust) Pty Ltd. Page 2
monoPAK Single channel portable dimme
r
monoPAK Sin
g
le channel portable dimmermonoPAK Sin
g
le channel portable dimme
r
monoPAK Single channel portable dimmer
Using the monoPAK
Using the monoPAKUsing the monoPAK
Using the monoPAK
Before using the monoPAK on your selected load, it is important to confirm that the power
required by the load does not exceed the output power rating of the monoPAK dimmer
(2400Watts@240Volts AC), otherwise the dimmer could be damaged.
The monoPAK is a versatile single channel 10Amp dimmer suitable for followspots, stage
props, photography studios, film locations, retail outlets, trade exhibititons etc… The integral
cables allow the monoPAK to be installed in series between an AC power source and a
dimmable load. Adjusting the sliding fader varies power to the load.
The load should NOT be connected or removed while the monoPAK is supplying power to the
load. Always adjust the sliding fader to the minimum position (0 power level) before adding
or removing a load.
Technical Specifications
Technical SpecificationsTechnical Specifications
Technical Specifications
Maximum output load 2400Watts @ 240V input.
Input Voltage Range 200 – 250VAC @ 50/60Hz.
Input Protection 10 Amp HRC M205 Fuse.
Inductor Rise Time 250-300usec (peak to peak).
RF suppression Input and output filters to CE requirements.
CE and C Tick Approved Yes.
Dimensions (excluding cables) 255mmL x 94mmW x 73mmD
Weight 4.0kg (5.0kg packed).
Construction Zinc steel finished in textured black powdercoat.,
Rear silk screened polycarbonate front panel.
Mounting Specifications
Mounting Specifications Mounting Specifications
Mounting Specifications
(mm)
256.0
234.0
15.0
94.0
47.0
LSC Lighting Systems (Aust) Pty Ltd. Page 3
monoPAK Single channel portable dimme
r
monoPAK Sin
g
le channel portable dimmermonoPAK Sin
g
le channel portable dimme
r
monoPAK Single channel portable dimmer
L
i
g
h
t
i
n
g
S
y
s
t
e
m
s
LSC Lighting Systems (Aust) Pty Ltd
7 University Place
Clayton 3168
Victoria Australia
ABN 21 090 801 675
www.lsclighting.com.au
email : [email protected]
mPAKU01A.doc
14/12/01
Disclaimer
DisclaimerDisclaimer
Disclaimer
LSC Lighting Systems (Aust) Pty Ltd supplies the enclosed information in good faith. LSC Lighting Systems (Aust) Pty Ltd makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any implied warranties
of merchantability or fitness for any particular purpose. Our policy is one of continual improvement and we reserve the right to
change circuitry, specifications or mode of operation of circuitry without obligation to notify any person or entity of such
revisions or changes.
/
