LED Flood Light User Guide
English
LED Flood Light User Guide
Thank you for ordering from Ustellar. Set-up is easy and takes only a few
minutes by following the instructions.
1 Please check if the light and the parts are intact before installation.
2 Make sure to cut o power before installation.
3 Please do not place this light in corrosive conditions.
4 If there is any damage to the cord, please cut o the power and stop
using it immediately.
5 Please do not retrofit the light within the warranty period.
6 To ensure the light works properly, please use the voltage indicated
on the packing.
Warning
1. Parameters
Model
Waage
Color Temperature
Max Luminous Flux
Input Voltage
Frequency
Waterproof Rating
Bean Angle
Controlled By
Baery for Controller
Life Expectancy
Working Temperature
UT88868
100W
5000K
10000lm
AC120V
50/60Hz
IP66
120°
IR Remote Controller
CR2025
50000Hr
-20-40
1
English
2
20cm/7.9in
D2D Sensor
& IR Receiver
IR Remote Controller
TIMER
BRIGHTNESS
D2D
80%
ON OFF
6H
10%
8H
2H 4H
100%
50%
English
3
English
Remove the plastic sheet from the boom of the remote
controller so as to activate the controller.
4
The light source of this luminaire is not replaceable, when the light
source reaches its end of life the whole luminaire shall be replaced.
TIMER
BRIGHTNESS
D2D
80%
ON OFF
6H
10%
8H
2H 4H
100%
50%
English
5.Remote Controller
5
Manual Mode
D2D Mode
Manual Mode:
Control the flood light constantly ON or OFF.
D2D Mode:
Dusk to Dawn mode, the light will turn on at night, and automatically
turn o in the morning.
TIMER
In D2D mode, turn on for 2/4/6/8 hours, then turn o, cycle daily.
BRIGHTNESS
Set the brightness level to 10%/50%/80%/100%.
Press 'D2D' buon will enter the D2D mode.
Press 'ON' or 'OFF' buon will exit the D2D mode.
Press '2H', '4H', '6H' or '8H' buon will enter the timer.
Press 'ON', 'OFF' or 'D2D' buon will exit the timer.
MODE1
TIMER
BRIGHTNESS
MODE3
D2D
80%
ON OFF
6H
10%
8H
2H 4H
100%
50%
English
The light source of this luminaire is not replaceable, when the light
source reaches its end of life the whole luminaire shall be replaced.
SUITABLE FOR WET LOCATIONS
SUITABLE FOR OPERATION IN AMBIENT NOT EXCEEDING 40°C
6
1. The remote controller has memory function, which means that it
can start at your last choice on mode and seings.
2. The flood light is controlled by the IR remote controller. To make
it work perfectly, please point the remote controller to the light and
make sure there is no obstacle between the light and the remote
controller for beer signal response.
3. After a period of usage, the remote controller might run out of
baery and become insensitive or the control distance may be
shortened. If the remote controller is not working, please try to
replace its baery as per instructions shown below. If the remote
controller still fails to work after replacing new baery, please
contact the seller for help.
Note:
English
www.ustellar.com support@ustellar.com
Contact Us
Have some issue? No worries! Please reach us via these channels.
Our customer services team is more than happy to help.
Manufacturer: Shenzhen Ustellar Technology Ltd.
(shen zhen shi you shi tuo ke ji you xian gong si )
Address: 308A, 3/F, Building A, Youth Entrepreneur Hub, Jianshe East
Road, Qinghua Community, Longhua Street, Longhua District,
Shenzhen, CHINA 518000
7
Manual Version: UT88125W-DW-US / V1.0
Step 1: Scan the QR code
Step 2: Click E-manual PDF file
Step 3: Read file online or download
/
