Abit USB-20V Quick Installation Manual

Abit
Brand
Abit
Model
USB-20V
Category
Interface cards/adapters
Type
Quick Installation Manual

Abit USB-20V: This USB 2.0 High-Speed PCI Host Card is compliant with Universal Serial Bus (USB) Specification Revision 2.0 and 1.1 and with PCI specification revision 2.2. It provides 4 external downstream Type-A USB ports, supporting all USB speeds and allowing data transfer speeds of up to 480 Mb/sec. The card also supports Plug & Play specification and comes with an Installation CD containing USB 2.0 drivers for Windows 98SE, Windows Me, Windows 2000, and Windows XP. With this card, you can connect up to 127 USB devices, including standard USB 1.1 or high-speed USB 2.

Abit USB-20V: This USB 2.0 High-Speed PCI Host Card is compliant with Universal Serial Bus (USB) Specification Revision 2.0 and 1.1 and with PCI specification revision 2.2. It provides 4 external downstream Type-A USB ports, supporting all USB speeds and allowing data transfer speeds of up to 480 Mb/sec. The card also supports Plug & Play specification and comes with an Installation CD containing USB 2.0 drivers for Windows 98SE, Windows Me, Windows 2000, and Windows XP. With this card, you can connect up to 127 USB devices, including standard USB 1.1 or high-speed USB 2.

USB-20V
Quick
Installation
Guide
Thank you for purchasing ABIT USB-20V USB2.0 High-Speed PCI Host Card. The purpose
of this guide is give you a quick introduction to installing this card properly.
USB-20V Specifications
Features:
Compliant with Universal Serial Bus (USB) Specification Revision 2.0 and 1.1
Compliant with PCI specification revision 2.2
High-Speed 480 Mb/sec data transfer speed
Provides 4 external downstream Type-A USB ports, supports all USB speeds
Supports Plug & Play specification
Links up to 127 Devices
Installation CD with USB 2.0 drivers for Windows
®
98SE, Windows
®
Me,
Windows
®
2000, and Windows
®
XP
Hardware Specification:
USB Host Controller
VIA VT6202 USB 2.0 Host Controller
Bus-System
32-bit PCI 2.2 standard
I/O Interface
4 external Type-A USB ports
Operating Systems Supported:
• Windows
®
98SE
• Windows
®
ME
• Windows
®
2000
• Windows
®
XP
USB-20V PCI Card Layout Diagram
4×External Ports
PCI Interface
4200-0269-02 Ver. 1.01
Installing the USB-20V PCI Host Card:
N
N
o
o
t
t
e
e
:
:
• Make sure to unplug the system power supply when adding or removing PCI
host cards as well as other system components. Failure to do so may cause
severe damage to both the motherboard and PCI host cards.
• Always observe static electricity precautions.
This section describes how to plug an PCI host card into your system’s riser card if you
have one or into any of the system's PCI slots. When plugged into the motherboard, it
allows you to expand the capabilities of the system.
To install an USB-20V PCI Host card, follow the steps below:
1. Remove the computer chassis cover.
2. Insert a flat blade screwdriver into a hole of the slot cover you wish to remove.
3. Move the screwdriver up and down until the slot cover breaks away from the chassis.
Then lift the slot cover out of the chassis.
4. When you handle the card, be careful not to touch any components on the circuit
board or the gold-edged connector.
5. Hold the card along the top corners and guide it into the slot. When the USB-20V
card reaches the slot on the motherboard, push the card in firmly to insert it fully.
6. Secure the end of the card to the computer with retaining screw.
7. Replace the system cover.
Connecting USB Devices
You can connect standard USB 1.1 or high-speed USB 2.0 devices to the USB Type-A
connectors of the USB2.0 PCI Host card, such as Mouse, Camera, Printer, Speakers, CD-RW,
MO, External HDD, Scanner, Keyboard…etc.
USB-20V
  • Page 1 1
  • Page 2 2

Abit USB-20V Quick Installation Manual

Abit
Brand
Abit
Model
USB-20V
Category
Interface cards/adapters
Type
Quick Installation Manual

Abit USB-20V: This USB 2.0 High-Speed PCI Host Card is compliant with Universal Serial Bus (USB) Specification Revision 2.0 and 1.1 and with PCI specification revision 2.2. It provides 4 external downstream Type-A USB ports, supporting all USB speeds and allowing data transfer speeds of up to 480 Mb/sec. The card also supports Plug & Play specification and comes with an Installation CD containing USB 2.0 drivers for Windows 98SE, Windows Me, Windows 2000, and Windows XP. With this card, you can connect up to 127 USB devices, including standard USB 1.1 or high-speed USB 2.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents