Commell LV-671CM6 User manual

LV-671Z

Mini-ITX Motherboard

User’s Manual

Edition: 1.12

2005/3/24

LV-671Z User’s Manual

2

LV-671Z User’s Manual

3

LV-671Z User’s Manual

4

Copyright

©

reserved. The information in this document is subject to change without prior notice to

make improvements to the products.

This document contains proprietary information and protected by copyright. No part of this

document may be reproduced, copied, or translated in any form or any means without prior

written permission of the manufacturer.

All trademarks and/or registered trademarks contains in this document are property of their

respective owners.

Disclaimer

The company shall not be liable for any incidental or consequential damages resulting from

the performance or use of this product.

The company does not issue a warranty of any kind, express or implied, including without

limitation implied warranties of merchantability or fitness for a particular purpose.

The company has the right to revise the manual or include changes in the specifications of

the product described within it at any time without notice and without obligation to notify any

person of such revision or changes.

Trademark

All trademarks are the property of their respective holders.

Any questions please visit our website at

http://www.commell.com.tw.

LV-671Z User’s Manual

5

Packing List

Please check the package before you use this product

Hardware:

LV-671Z Mini-ITX motherboard x 1

Cable Kit:

40-pin ATA100 IDE Cable x 1

26-pin Slim Type Floppy Cable x 1

4-pin to 4-pin Power Cable x 1

CD Content

Driver

User’s Manual

LV-671Z User’s Manual Index

6

Index

Chapter 1 <Introduction>.....................................................................................9

1.1 <Product Overview>.................................................................................9

1.2 <Product Specification> .........................................................................10

1.3 <Component Placement> ......................................................................13

1.4 <Block Diagram>....................................................................................14

Chapter 2 <Hardware Setup>.............................................................................15

2.1 <Connector Location>............................................................................15

2.2 <Jumper Reference> .............................................................................16

2.3 <Connector Reference>.........................................................................17

2.3.1 <Internal Connector>..................................................................17

2.3.2 <External I/O connector> ...........................................................17

2.4 <System Setup>.....................................................................................18

2.4.1 <Memory Installation>................................................................18

2.5 <CMOS Setup>......................................................................................19

2.6 <IDE Interface>......................................................................................20

2.7 Compact Flash Interface........................................................................21

2.8 <Display Interface>................................................................................22

2.8.1 <Analog display interface>.........................................................22

2.8.2 <Digital display interface> ..........................................................22

2.9 <Audio Interface>...................................................................................26

2.10 <Ethernet Interface> ............................................................................28

2.11 <Power and Fan connector>................................................................29

2.12 <GPIO Interface>.................................................................................31

2.13 <Expansive Interface> .........................................................................32

2.14 <Switch and Indicator>.........................................................................33

Chapter 3 <System Setup> ................................................................................35

3.1 <Watchdog Timer Setting>.....................................................................35

3.2 <Audio Setting>......................................................................................36

3.3 <Display Device Setup>.........................................................................37

LV-671Z User’s Manual Index

7

Chapter 4 <BIOS Setup> ....................................................................................41

Appendix A <I/O Port Pin Assignment>............................................................43

A.1 <IDE Port>.............................................................................................43

A.2 <Floppy Port> ........................................................................................45

A.3 < USB Interface >..................................................................................45

A.4 <IrDA Port>............................................................................................46

A.5 < VGA Port >..........................................................................................46

A.6 < LAN Port >..........................................................................................46

A.7 < Serial Port >........................................................................................47

Appendix B <Flash BIOS>..................................................................................49

B.1 <Flash Tool> ..........................................................................................49

B.2 <Flash BIOS Procedure>.......................................................................49

Appendix C <System Resource> ......................................................................51

C.1 <I/O Address Map>................................................................................51

C.2 <Memory Address Map> .......................................................................53

C.3 <System IRQ and DMA Resource>.......................................................54

Contact Information............................................................................................56

LV-671Z User’s Manual

8

(This Page is Left for Blank)

LV-671Z User’s Manual Introduction

Chapter 1 <Introduction>

1.1 <Product Overview>

LV-671Z is an all-in-one industrial compact Pentium-M level motherboard based on

Mini-ITX form factor at 170 x 170 mm of dimension. Based on Intel 852GM and ICH4

chipset, LV-671Z offers the compact, embedded, value and high performance solution with

Intel Celeron M CPU, 400 MHz of FSB, 1GBytes DDR200/266 SDRAM, Intel 852GM

GMCH built-in Intel Extreme Graphics Technology, Intel PRO/1000+ LAN, Hi-Speed USB

2.0, 5.1 channel and S/P DIF 3D audio, 18/24-bit dual channel LVDS, GPIO and

embedded flash disk interfaces.

Low Power Consumption Solution

Based on Intel 852GM chipset and Intel Celeron M processor, the board requires

lower power consumption than Pentium 4 –M processors. The embedded Intel Celeron M

of ultra low voltage provides the ability for fanless system.

Dual Display Architecture

Intel 852GM supports independent display interface; users can apply two display

devices for dual display clone or extended desktop display. With this feature, system

integrator can use this board for Kiosk, ATM, or industrial control machines.

5.1 Channel AC97 Audio

LV-671Z integrates a REALTEK 5.1 channel AC97 codec; users can enjoy the live

surround sound through 5.1 channel speakers. LV-671Z also has an S/PDIF jack for digital

sound outputting.

Hi-Speed USB 2.0 Interface

Intel ICH4 built-in Hi-Speed USB 2.0 controller let LV-671Z offer up to 480Mbps of

transferring rate.

Card Bus and Embedded Flash Disk

The LV-671Z support PCMCIA Type I/II enable you can simply use the wireless LAN

module or other extended devices, the Compact Flash interface and IDE1 with DOM

support can let you port any embedded system onboard.

Mini-PCI and Mini-AGP interface

With Mini-PCI interface, users can add a wireless LAN module or video capture

module for powerful communication solutions. With Mini-AGP interface, users can apply

the additional video output module such as HDTV or DVI.

Product Overview 9

LV-671Z User’s Manual Introduction

1.2 <Product Specification>

General Specification

Form Factor Mini-ITX motherboard at 170 x 170 mm (L x W)

CPU Embedded Intel Celeron M 600MHz

Package: mBGA 479

FSB: 400MHz

Memory 1GBytes DDR200/266 SDRAM on one 184-pin DIMM socket

Unbuffered, non-ECC supported

Chipset Intel 82852GM GMCH and 82801DB ICH4

BIOS Phoenix-Award v6.00PG 4Mb PnP flash BIOS

Green Function Power saving mode includes doze, standby and suspend modes.

ACPI version 1.0 and APM version 1.2 compliant

Watchdog Timer System reset programmable watchdog timer with 1 ~ 255

sec./min. of timeout value

Real Time Clock Intel ICH4 built-in RTC with lithium battery

Enhanced IDE PCI enhanced IDE interface supports dual channels and up to 4

ATAPI devices at UltraATA/100

One 40-pin and one 44-pin IDE port

DiskOnModule (DOM) embedded flash disk up to 1GBytes

Multi-I/O Port

Chipset Intel 82801DB ICH4 (USB) and Winbond W83627HF-AW LPC

Super I/O controller

Serial Port Two external RS-232 serial port with 16C550 compatible UART

and 16 bytes FIFO

USB Port Six Hi-Speed USB 2.0 ports with 480 Mbps of transfer rate

Two external and four internal USB ports

Parallel Port One external bi-direction parallel port with SPP/ECP/EPP mode

Floppy Port One slim-type FDD port supports up to two FDD

IrDA Port One IrDA compliant Infrared interface supports SIR

K/B & Mouse External PS/2 keyboard and mouse ports on rear I/O panel

GPIO One 20-pin Digital I/O connector with 15-bit programmable I/O

interface

Card Bus

PCMCIA One PCMCIA Type I/II slot

Product Specification 10

LV-671Z User’s Manual Introduction

VGA Display Interface

Chipset Intel 852GM GMCH built-in Intel Extreme Graphics Technology

With 133MHz VGA core and 256-bit 3D engine

Frame Buffer Intel DVMT (Dynamic Video Memory Technology) 2.0 up to

64Mbytes shared with system*

Display Type CRT and LCD monitors for analog display

24-bit single/dual channel LCD panel for digital display

Connector External DB15 female connector on rear I/O panel

Internal 40-pin LVDS connector

*Under Windows 98/ME/2000/XP/Server2003 or Linux kernel 2.4 later

Ethernet Interface

Chipset Intel PRO/1000+ LAN interface with Intel 82540EM

Type 10Base-T / 100Base-TX/1000Base-T,

auto-switching Fast Ethernet

Full duplex, IEEE802.3U compliant

Connector External RJ45 connector with LED on rear I/O panel

Audio Interface

Chipset Intel ICH4 with REALTEK ALC655 AC97 3D audio codec

Interface 5.1 channel 3D audio with front (R/L), rear (R/L), center and bass

Optical Fiber digital audio encoding signal output

Connector Optional external three phone jack for 5.1 channel audio onboard

External Amplified Speaker output jack on rear panel

External SPDIF connector on rear panel

Internal 10-pin header for line-in/-out, MIC-out, 4-pin header for

CD-in

Solid State Disk Interface

Flash Type Compact Flash Type-I/II for Compact Flash Card or IBM Micro Drive

Capacity Up to 1GB flash memory

Expansion Interface

Slim PCI Slot One slim type PCI slot supports up to 2 bus master PCI

32-bit, 33MHz

Mini-PCI One Mini-PCI socket with 32-bit, 33MHz for LV-671ZMP series

Mini-AGP One Mini-AGP socket with DVO bus for LV-671ZMA series

Product Specification 11

LV-671Z User’s Manual Introduction

Power and Environment

Power

Requirement

One external 19V/12V (auto switching) DC Adapter connector on

rear panel

4-pin onboard 12V P4 4-pin power connector

(Two power resources selectable for each)

Input Voltage

Range

11V ~ 13V for 12V power supply

16V ~ 20V for 19V power supply

Input Current 12V/60W (with one 5.25” CDROM and 3.5” HDD)

19V/60W (with one 5.25” CDROM and 3.5” HDD)

Dimension 170 (L) x 170 (H) mm, Mini-ITX form factor

Temperature Operating within 0 ~ 60

o

C (32 ~ 140

o

F)

Storage within -20 ~ 85

o

C (-4 ~ 185

o

F)

Ordering Code

LV-671ZMA Embedded Mini-ITX Intel Celeron M processor Motherboard

with Intel Extreme VGA, LAN, 5.1-CH/SPDIF Audio,

Hi-Speed USB 2.0, mini-AGP socket and LVDS interface.

LV-671ZMP Embedded Mini-ITX Intel Celeron M processor Motherboard

with Intel Extreme VGA, LAN, 5.1-CH/SPDIF Audio,

Hi-Speed USB 2.0, mini-PCI socket and LVDS interface.

LV-671ZNSMA Same as LV-671ZMA but without PCMCIA & Compact Flash

LV-671ZNSMP Same as LV-671ZMP but without PCMCIA & Compact Flash

For further product information please visit the website at http://www.commell.com.tw

Product Specification 12

LV-671Z User’s Manual Introduction

1.3 <Component Placement>

1 x 184-pin DDR266 DIMM up to 1GB

Intel 852GM

(Northbridge)

Intel ICH4

(Southbridge)

Embedded

Intel Celeron M

600MHz

Onboard DC

to DC inverter

Intel 82540EM

Gigabit LAN

REALTEK

ALC655 5.1CH

A

udio Codec

Component Placement 13

LV-671Z User’s Manual Introduction

1.4 <Block Diagram>

400MHz FSB

852GM

CRT

DVO B/C

Mini-AGP

ICH4

ATAPI Devices

USB Devices

480Mb/s

UltraATA100

USB2.0

Audio

AC97 Codec

Compact Flash

IrDA

PS/2

COM Port

Parallel

Port

Floppy

LPC

33MHz

PCI Bus

PCMCIA

Mini-PCI

Slim PCI

Gigabit Ethernet

Controller

DDR200/266

1 x 184-pin

DIMM

Up to 1GB

LVDS

LCD

Embedded Intel Celeron M 600MHz CPU

Block Diagram 14

LV-671Z User’s Manual Hardware Setup

Chapter 2 <Hardware Setup>

This chapter contains the information for installation of hardware. The install procedure

includes jumper settings, CPU and memory installation, fan, I/O and panel connections.

2.1 <Connector Location>

CN_BPWR CN_INV DIMM IDE1 CN_LVDS IDE2 CN_USB1 CN_USB2

MINI_AGP

MINIPCI

CN_IR

CPUFAN

CN 12V

CN_SPWR

JFRNT

SYSFAN

CN_DIO

PCI

FDD

CN_WOL

CN_AUDIO

CDIN

CN_2ND_IO CN_LAN2

DC_IN PS/2 Printer LAN COM2/1

VGA SPEAKER SP/DIF Dual_USB PCMCIA

Connector Location 15

LV-671Z User’s Manual Hardware Setup

2.2 <Jumper Reference>

Jumper Function

JRTC COMS Operate / Clear Setting

JLAN LAN1 Enable/Disable

JVLCD LCD Panel Voltage Setting

JCFSEL Compact Flash Address Setting

JDOM IDE1 5V Voltage Enable/Disable

JDOM JCFSEL JVLCD

JRTC

JLAN

Jumper Reference 16

LV-671Z User’s Manual Hardware Setup

2.3 <Connector Reference>

2.3.1 <Internal Connector>

Connector Function Remark

DIMM 184-pin DIMM Socket Standard

IDE1 40-pin Primary IDE Port Standard

IDE2 44-pin Secondary IDE Port Standard

FDD 26-pin slim type FDD Port Standard

CN_USB1 10-pin 3

rd

/ 4

th

Hi-Speed USB 2.0 Port Standard

CN_USB2 10-pin 5

th

/ 6

th

Hi-Speed USB 2.0 Port Standard

CN_IR 5-pin SIR IrDA Port Standard

CN_12V 4-pin AT Power Connector Standard

CN_BPWR 4-pin 5V&12V output connector Standard

CN_SPWR 4-pin 5V&12V output connector Standard

JFRNT 14-pin Switch and Indicator Connector Standard

CPUFAN 3-pin +12V CPU Fan Connector Standard

SYSFAN 3-pin +12V System Fan Connector Standard

CN_AUDIO 10-pin Audio Port Standard

CDIN 4-pin CD-in Interface Standard

CN_WOL 3-pin Wake-On-LAN Interface Standard

CN_LVDS 40-pin LVDS connector Standard

CN_INV 5-pin LCD Inverter Power Connector Standard

CN_DIO 20-pin programmable I/O connector Standard

CN_LAN2 Additional Ethernet Controller Interface Standard

CN_2ND_IO Additional I/O module interface Standard

CF Compact Flash Card Interface Standard

PCMCIA PCMCIA Card bus interface Standard

2.3.2 <External I/O connector>

Connector Function Remark

DC_IN 4-pin 12V/19V auto-switching input Standard

PS2 PS/2 type keyboard and mouse port Standard

Printer DB26 parallel port Standard

VGA DB15 VGA port Standard

SPEAKER Amplified speaker out Standard

SPDIF Digital audio output Standard

LAN RJ45 LAN port Standard

DUAL_USB USB connectors Standard

COM1/2 RS232 DB9 serial port Standard

PCMCIA Car bus slot Standard

Connector Reference 17

LV-671Z User’s Manual Hardware Setup

2.4 <System Setup>

2.4.1 <Memory Installation>

The board supports one 184-pin DDR200/266 (PC1600/PC2100) SDRAM up to 1GB of

capacity, and supports non-ECC, unbuffered memory modules.

DIMM

104-pin 80-pin

Please check the pin number to match the socket side well

before installing memory module.

Memory Installation 18

LV-671Z User’s Manual Hardware Setup

2.5 <CMOS Setup>

The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to

inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its

default values.

Jumper: JRTC

Type: Onboard 3-pin Header

JRTC Mode

1-2 Clear CMOS

2-3 Normal Operation

Default setting

1

3

JRTC

CMOS Setup 19

LV-671Z User’s Manual Hardware Setup

2.6 <IDE Interface>

The board supports two IDE interface up to 4 ATAPI devices, base on Intel ICH4, the IDE

interface supports ATA66/100 ATAPI drives. The IDE1 supports +5V on pin-20 for DOM

(Disk on Module), the jumper JDOM can let you select enable/disable this support.

Jumper: JDOM

Type: onboard 3-pin header

JDOM Mode

ON IDE1 pin-20 5V power supply enable

OFF No 5V power supply on IDE1 pin-20

Default setting

39

1

JDOM

IDE1 (40-pin pitch=2.54)

40

2

1

43

IDE2 (44-pin pitch=2.00)

2

44

IDE Interface 20

Page is loading ...

Commell LV-671CM6 User manual

Commell LV-671CM6 User manual

Related papers

Other documents