Reliable 6000FS User manual

Brand: Reliable

Model: 6000FS

Type: User manual

8” STRAIGHT KNIFE INSTRUCTION MANUAL

6000FS

INSTRUCTION MANUAL

RELIABLE. RIGHT THERE WITH YOU.

At Reliable, we do what we love, and take pride in doing it right.

You want what’s best for the people, places and things that matter

in your life – from where you live to what you wear. So do we. From

the start, we approach every product with a craftsman’s attention

to detail and passion for making it right. Quality, functionality,

design and customer service play an equally important part in

delivering what’s right for you. The 6000FS is your best choice for

cuts that are up to 8” in height. It’s designed with a low center of

gravity for ease of handling and features the best power to weight

ratio in the industry.

For your safety and to fully enjoy the advantages of this product,

please take a few minutes to read all the important safeguards

and care instructions. Keep this manual handy and review the

product warranty for your reference.

IMPORTANT SAFETY REQUIREMENTS

Before operating the motor, be sure that the electrical supply voltage and current are

the same as stamped on the label. Fill the oil cup. Push in the turning knob and turn the

machine over a few revolutions by hand to see if the knife moves easily.

MACHINE CARE

1. Clean lint out of sharpener twice a week.

2. Remove cover over cam and clean out lint around screw mechanism in sharpener once

a week.

3. Remove knife and clean slides with slot cleaner once a day.

4. To prevent accumulation of lint, do not oil plate rollers.

5. If rollers stick, remove rollers from the plate and wash them with a cleaning solvent.

WARNING

This machine is equipped with a sharp

knife. Keep hands away from the knife area

at all times. When operating or handling the

machine, be sure to only use control levers

and handles. Do not operate sharpener

without the knife in the machine or the

sharpener will become damaged.

SHARPENING THE KNIFE

Take the machine out of the lay. Drop the

pressure foot lever, using the pressure

foot lever located next to the machine’s

operating handle. Press the release lever

downward slowly, with ﬁrm pressure to

engage the sharpening mechanism. If lever

locks, lift latch lever and restart.

To change the knife blade, press in the

turning knob and position the blade to its

lowest point. Insert the blade removal tool

and loosen the knife lock-bolt. Remove the

blade through the bottom of the knife slot.

Insert a new blade into the knife slot and

tighten the knife lock-bolt.

PART NO.

DE1

DE2

DE3

DE4

DE5

DE6

DE7

DE8

NO. REQ’D

DESCRIPTION

SHARPENER HOLD-DOWN NUT

FRONT-TO-REAR BEARING NUT

PLATE BOLD NUT

STANDARD-BEARING SCREW

FRONT-REAR-BEARING SCREW

SCREW

KNIFE

PART NO.

DE9

DE10

DE11

DE12

DE13

DE14

DE15

DE16

DE17

DE18

DE19

DE20

DE21

DE22

DE23

DE24

DE25

DE26

DE27

DE28

DE29

DE30

DE31

DE32

DE33

DE34

DE35

NO. REQ’D

DESCRIPTION

TERMINAL WIRE TUBING

STATOR WITH BAND

ROTOR AND SHAFT

CARRYING HANDLE

SCREW

TERMINAL WIRE TUBING

REAR BALL BEARING

TERMINAL

REAR BEARING HOUSE

TERMINAL BLOCK

ATTACHMENT PLUG

SCREW

CUTOUT SWITCH MOUNT

AUTOMATIC CUTOUT

AUTOMATIC CUTOUT SWITCH

SHAFT COVER FOR CUTOUT

SCREW

COVER FOR CUTOUT

ROTOR FAN

LEADING SPING WASHER

CLUTCH NUT

RETAINING RING

FAN COVER

SCREW

CLUTCH SPING

TURNING KNOB

PART NO.

DE36

DE37

DE38

DE39

DE40

DE41

DE42

NO. REQ’D

DESCRIPTION

SCREW

CAPACITOR COVER

CAPACITOR

COVER FOR CAPACITOR

SPRING FOR CAPACITOR

SHAFT LOCK NUT

PART NO.

DE43

DE44

DE45

DE46

DE47

DE48

DE49

DE50

DE51

DE52

DE53

DE54

DE55

DE56

DE57

DE58

DE59

DE60

DE61

DE62

DE63

DE64

DE65

DE66

DE67

DE68

DE69

DE70

DE71

DE72

DE73

DE74

DE75

DE76

DE77

DE78

DE79

DE80

DE81

DE82

DE83

DE84

DE85

DE86

DE87

DE88

DE89

DE90

NO. REQ’D

DESCRIPTION

FRONT BEARING HOUSING

BEARING

FRONT BALL BEARING RETAINER

SCREW

WASHER

NUT

CRANK

STUD, UPPER

STUD, LOWER MOUNTING

GUIDE ADJUSTMENT NUT

SHAFT FOR BALL BEARING

SEATED FOR BALL BEARING

LOCK NUT FOR SHAFT

CRANK BALL BEARING LOCK NUT

CONNECTING ROD

SCREW

H.GUIDE

CROSS HEAD

WRIST PIN

WRIST PIN FELT PAD

CONNECTING ROD WASHER

SCREW

GUIDE WASHER

SCREW

KNIFE LOCK WASHER

SCREW

HANDLE BRACKET

SCREW

SCREW FOR HANDLE BRACKET

OPERATING HANDLE LOCK NUT

OPERATING HANDLE

SWITCH

SWITCH BASE

SCREW

OILING DEVICE

OIL TUBE

EYELET

COVER OIL TUBE

LONG WICHKING

SCREW

CIRCLE

WINDOWS FOR OIL

OIL TUBE COVER

OIL HOLE COVER

PART NO.

DE91

DE92

DE93

DE94

DE95

DE96

DE97

DE98

DE99

DE100

DE101

DE102

DE103

DE104

DE105

NO. REQ’D

DESCRIPTION

STANDARD

KNIFE SLIDE

THROAT PLATES

TAPER PIN

SCREW

PLATE WING

PLATE

RUBBER ROLLER ALL SET

ROLLER SHELL

RUBBER MOUNTED ROLLER

CLAMP SCREW FOR ROLLER

HINGE PIN

PLATE WING SPRING

LOCK WASHER #8

PART NO.

DE106

DE107

DE108

DE109

DE110

DE111

DE112

DE113

DE114

DE115

DE116

DE117

DE118

DE119

DE120

DE121

DE122

DE123

DE124

DE125

DE126

DE127

DE128

DE129

DE130

DE131

DE132

DE133

DE134

DE135

DE136

DE137

DE138

DE139

DE140

DE141

DE142

DE143

DE144

DE145

DE146

DE147

DE148

DE149

DE150

NO. REQ’D

DESCRIPTION

CAP OF TUBE

STOP NUT FOR SCREW SHAFT

NUT FOR SCREW SHAFT

THRUST WASHER FOR NUTS

THRUST BALL BEARING

L.H. NUT FOR SCREW SHAFT

R.H. NUT FOR SCREW SHAFT

SCREW SHAFT

COLLAR FOR FXTENSIOM

RELEASE LEVER WITH CAM

SHARPENER HOUSING (WITH BUSHINGS AND TUBES)

SPRING WASHER FOR RELEASE LEVER

RELEASE LEVER WITH CAM

CAM

SCREW

SET SCREW FOR CAM

SCREW FOR RELEASE LEVER

LATCH FOR CAM

SPRING FOR LATCH

SCREW FOR LATCH

BEARING FOR CAM SHAFT

SHAFT FOR CAM

CAM SPRING

CAM SHAFT SPRING SCREW

PRESSURE FOOT LEVER

SPRING FOR PRESSURE FOOT LEVER

PRESSURE FOOT LEVER SCREW

SPACER FOR KNIFE GUARD LOCK BRACKET

KNIFE GUARD LOCK BRACKET COMPLETE

LOCK FOR PRESSURE FOOT

SPRING FOR KNIFE GUARD LOCK

NUT FOR PRESSURE FOOT LOCK

KNIFE GUARD LOCK BRACKET ONLY

SCREW FOR KNIFE GUARD LOCK

SCREW

PRESSURE FOOT LOCK BRACKET COMPLETE

COVER OVER CAM

SCREW

SCREW FOR PRESSURE FOOT SHOE

PRESSURE FOOT SHOE

SCREW

LIFT HANDLE FOR KNIFE GUARD ROD

KNIFE GUARD ROD

PART NO.

DE151

DE152

DE153

DE154

DE155

DE156

DE157

DE158

DE159 DE160

DE161

DE162

DE163

DE164

DE165

DE166

DE167

DE168

DE169

DE170

DE171

DE172

DE173

DE174

DE175

DE176

DE177

DE178

DE179

DE180

DE181

DE182

DE183

DE184

DE185

DE186

DE187

DE188

DE189

DE190

DE191

DE192

DE193

DE194

DE195

NO. REQ’D

DESCRIPTION

R.H. FOLLOWER NUT

L.H. FOLLOWER NUT

SQUARE SHAFT

TUPE FOR SQUARE SHAFT

TUNE FOR SCREW SHAFT

SHARPENER HOUSING

FELT PAD FOR OIL RETAINER-IDLER GEAR

OIL READER-IDLER GEAR

SCREW

SHAFT FOR GRANK

IDLER GEAR

GEAR AND SHAFT

BELL GRANK

BALL BEARING FOR GRANK

SPACER FOR BELL BEARINGS

RETAINING RING FOR BELL CRANK

DRIVE PULLEY WITH DRIVER

BEARING FOR BELL GRANK

WASHER FOR SHAFT

RETAINING RING FOR SHAFT

PIN FOR BELL GRANK

BEARING FOR DRIVE SHAFT

THRUST WASHER 15

SPIRAL GEAR 15

BEARING FOR DRIVE SHAFT

KEY

DRIVER FOR SHAFT WITH GEAR

LOCK NUT FOR SHAFT

PIN FOR SHARPENER HOUSING

SPRING FOR BELL GRANK

BEARING FOR GEARS 20

SPUR GEAR 20

THRUST WASHER FOR BOTTOM PLATE

PUSH ROD

ROLL FOR PUSH ROD

BEARING FOR SCREW SHAFT

BOTTOM PLATE

OIL PAD AND HOLDER

SPREADER PIN

SCREW

RIVET

H. OIL PAD

PART NO.

DE196

DE197

DE198

DE199

DE200

DE201

DE202

DE203

DE204

DE205

DE206

DE207

DE208

DE209

DE210

DE211

DE212

DE213

DE214

DE215

DE216

DE217

DE218

DE219

DE220

DE221

DE222

DE223

DE224

DE225

DE226

DE227

DE228

DE229

DE230

DE231

DE232

DE233

DE234

DE235

DE236

NO. REQ’D

DESCRIPTION

L.H. SHAFT EXTENTION 8

R.H. SHAFT EXTENSION

ADJUSTING SCREW

SCREW

GEAR COVER

SCREW

GUIDE BACK OF SHANDARD

SPRING FOR ARM

CLAMING ARM FOR SHOE

SCREW FOR CLAMPERING ARM

SCREW

STABILIZER

NUT FOR SHARPENER SHOE SCREW

SCREW #4-36X3/16 FILLISTER HEAD

INTERMEDIATE GEAR

LOWER GEAR BRACKET WITH COVER

WEAR PLATE

SPING FOR PULLEYSLIDE

R.H. SLIDE WITH PULLEY

SLIDE WITH PULLEY

GEAR ON SCREW SHAFT 24

GREASE PLUG

BEARING FOR SCREW SHAFT

BEARING FOR INTERMEDIATE GEAR

BEARING FOR SHAFT EXTENSION

FRONT PULLEY TOR BELT

ROLL PIN

NEOPRENE BAND FOR PULLEY

R.H. PRE-SET SHARPENER SHOE (ONLY)

L.H. PRE-SET SHARPENER SHOE (ONLY)

WASHER

R.H. PRE-SET SHARPENER SHOE

L.H. PRE-SET SHARPENER SHOE

BUSING FOR SHARPENER SHOE

R.H. SHARPENER SHOE SPRING

L.H. SHARPENER SHOE SPRING

SCREW FOR SHARPENER SHOE

SHON SCREW

JAM NUT

BELT

Reliable Corporation (“Reliable”) warrants to original purchaser of its products that

every product sold by Reliable (a “Reliable Product”) is free from defects in material

and workmanship for a period of one year from the date of purchase if properly used

and maintained. Subject to the conditions and limitations set forth below, Reliable will

either repair or replace any part of a Reliable Product that proves defective by reason

of improper workmanship or materials. If the defective Reliable Product is no longer

available and cannot be repaired effectively or replaced with an identical model, Reliable

shall replace the defective Reliable Product with a current Reliable Product of equal or

greater value. Repaired parts or replacement products will be provided by Reliable on an

exchange basis, and will be either new or refurbished to be functionally equivalent to new.

If Reliable is unable to repair or replace a Reliable Product, it will refund the current value

of that Reliable Product at the time the warranty claim is made.

This limited warranty does not cover any damage to a Reliable Product that results from

improper installation, accident, abuse, misuse, natural disaster, insufﬁcient or excessive

electrical supply, abnormal mechanical or envsteamermental conditions, wear and tear

resulting from normal use of the product, or any unauthorized disassembly, repair, or

modiﬁcation. This limited warranty does not extend to any indirect, consequential or

incidental damages that may be suffered by a user or from the use of a Reliable Product,

including without limitation, any liability for third party claims for damage, and is limited

to the amount paid by the original purchaser Reliable Product with respect to which this

limited warranty protection applies. This limited warranty does not apply with respect to

products that have been altered or which are missing serial numbers or for products not

purchased directly from Reliable or a dealer authorized by us to sell Reliable Products.

This limited warranty is the only warranty that applies to any Reliable Product, supersedes

any and all terms that may be contained in any other document or purchase order and

may not be altered or amended except expressly in writing by Reliable.

To obtain a repair or replacement under the terms of this warranty, please contact our

customer service group at 1-800-268-1649 or at support@reliablecorporation.com.

You will be required to submit an original receipt via fax or e-mail. The receipt must reﬂect

that you are the original purchaser, the product was bought directly from

us or from an authorized Reliable dealer and that the warranty claim is being made within

the warranty period. You will be issued a return authorization number (RA#) and asked to

ship the defective product together with proof of purchase and RA#, prepaid insured to

the following address:

Reliable Corporation, 5-100 Wingold Avenue, Toronto, ON M6B 4K7. Freight collect

shipments will be refused. The risk of loss or damage in transit will be borne by

the customer. Once Reliable receives the defective product, it will initiate the repair or

replacement process.

If you have any questions regarding this warranty, you may write to:

Reliable Corporation

100 Wingold Avenue, Unit 5

Toronto, Ontario

Canada M6B 4K7

www.reliablecorporation.com

RELIABLE PRODUCTS WARRANTY

1 800 268 1649

www.reliablecorporation.com

Reliable 6000FS User manual

Reliable 6000FS User manual

Reliable 6000FS User manual

Related papers

Other documents